2009 PEUGEOT 207 change time

30
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life. Lighting rheostat
System for manual adjustment of the
brightness of the instruments and controls
in relation to the exterior brightness. CLOCK
Integrated system which displays the time with independent setting of the hours and minutes.
The total and trip distances are displayed for
thirty seconds when the ignition is switched
off, when the driver's door is opened and
when the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the button
until zeros appear. Activation
When the lights are on:

 press the button to change the
brightness of the instruments and
controls,

 when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,


when the lighting reaches the level of
brightness required, release the button.
Deactivation
When the vehicle lighting is off, or in
day mode on vehicles fi tted with day-
time running lamps, pressing the button
does not have any effect. Setting
 Press the corresponding button briefl y to obtain slow scrolling.
or
Continue to press the correspondingbutton to obtain rapid scrolling.
Button 1 : setting of the hours.
Button 2 : setting of the minutes.

33
MONOCHROME SCREEN A
(WITH PC SOUND)
Controls
Displays on the screen
This displays the following information:
- the time,
- the date,
- the ambient temperature * (this fl ashes if there is a risk of ice),
- the status of the openings (doors, boot, ...),
- the audio sources (radio, CD, ...),
- the trip computer (refer to the end of the section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Boot open") may ap-
pear temporarily. These can be cleared
by pressing the "ESC" button. General menu

 Press the "MENU" button to gain
access to the general menu , then
press the "  " or "  " buttons to
scroll through the various menus:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- language,
- units.

 Press the "OK" button to select the
menu required.
From the audio equipment control panel,
you can:

 press the "MENU" button to gain
access to the general menu ,

 press the "  " or "  " buttons to scroll
through the items on the screen,

 press the "MODE" button to change
the permanent application (trip com-
puter, audio source, ...),

 press the "  " or "  " buttons to
change a setting value,

 press the "OK" button to confi rm,
or

 press the "ESC" button to abandon
the operation in progress. Radio-CD
With the audio equipment switched on,
once the "Radio-CD" menu has been
selected you can activate or deactivate
the functions linked with use of the ra-
dio (RDS, REG) or the CD (introscan,
shuffl e, CD repeat).
For more information on the "Radio-CD"
application, refer to the PC Sound part
of the "Audio and Telematics" section.
* With air conditioning only.

35
MONOCHROME SCREEN C
(WITH PC SOUND)
General menu
Displays on the screen
This displays the following information:
- the time,
- the date,
- the ambient temperature * (this fl ashes if there is a risk of ice),
- the status of the openings (doors, boot...),
- the audio sources (radio, CD...),
- the trip computer (refer to the end of the section).
Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Automatic headlamp
lighting activated") may appear tempo-
rarily. These can be cleared by pressing
the " ESC " button. Controls
From the audio equipment control panel,
you can:

 press the " MENU " button to gain ac-
cess to the general menu ,

 press the "  " or "  " buttons to scroll
through the items on the screen,

 press the " MODE " button to change
the permanent application (trip com-
puter, audio source...),

 press the "  " or "  " buttons to
change a setting value,

 press the " OK " button to confi rm,
or

 press the " ESC " button to abandon
the operation in progress. "Audio functions" menu
With the audio equipment switched on,
once this menu has been selected you
can activate or deactivate the functions
linked with use of the radio (RDS, REG,
RadioText) or the CD (introscan, shuf-
fl e, CD repeat).
For more information on the "Audio func-
tions" application, refer to the PC Sound
part of the "Audio and Telematics" section.
* With air conditioning only.
 Press the " MENU " button to gain
access to the general menu :
- audio functions,
- trip computer (refer to the end of the section),
- personalisation-confi guration,
- telephone (hands-free kit).

 Press the " 
" " " buttons to select
the menu required, then confi rm by
pressing the " OK " button.

!
37
Defi ne the vehicle parameters
Once this menu has been selected, you
can activate or deactivate the following
equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- "guide-me-home" lighting (refer to the "Visibility" section). Choice of language
Once this menu has been selected, you
can change the screen display language
(Deutsch, English, Espanol, Français,
Italiano, Nederlands, Portugues,
Portugues-Brasil, Türkçe * ).
"Telephone" menu
With the audio equipment switched on,
once this menu has been selected you
can confi gure your Bluetooth hands-
free kit (pairing), consult the various
telephone directories (calls log, serv-
ices...) and manage your communica-
tions (pick up, hang up, call waiting, se-
cret mode...).
For further details concerning the "Tel-
ephone" application, refer to the PC
Sound part of the "Audio and Telemat-
ics" section.
Example: setting of the duration of the
"guide-me-home" lighting
"Personalisation-Configuration"
menu
Once this menu has been selected, you
can gain access to the following func-
tions:
- defi ne the vehicle parameters,
- display confi guration,
- choice of language.
 Press the "  " or "  " buttons, then
the " OK " button to select the menu
required.

 Press the "  " or "  " buttons, then
the " OK " button to select the "Guide-
me-home headlamps" line.

 Press the "  " or "  " buttons to set
the value required (15, 30 or 60 sec-
onds), then press the " OK " button to
confi rm.

 Press the "  " or "  " buttons, then
the " OK " button to select the " OK "
box and confi rm or press the " ESC "
button to cancel.
Display confi guration
Once this menu has been selected, you
can gain access to the following set-
tings:
- brightness-video setting,
- date and time setting,
- selection of the units.
For safety reasons, it is imperative
that confi guration of the multifunc-
tion screens by the driver is done
only when stationary.
* According to country.

i
!
40
Once the "Display confi guration" menu
has been selected, you gain access to
the following parameters:
- selection of the palette of colours available for the display,
- setting of the brightness and bril- liance of the display,
- setting of the date and time (12 or 24 hour mode, adjustment of the
minutes on GPS),
- selection of the units (temperature in °Celsius or °Fahrenheit; consump-
tion in l/100 km or mpg or km/l).
Display confi guration
"Video" menu
Sounds
Once the "Sounds" menu has been se-
lected, you gain access to the following
parameters:
- setting of the voice commands,
- setting of the voice synthesiser
(volume, male or female),
- activation of the auxiliary input AUX.
Choice of language
Once the "Choice of language" menu
has been selected, you gain access to
the following parameters:
- selection of the display language (Français, English, Italiano, Portugues,
Espanol, Deutsch, Nederlands,
Türkçe * ),
- selection of the information and voice commands language (Français,
English, Italiano, Portugues, Espanol,
Deutsch, Nederlands, Türkçe * ).
You can connect video equipment
(camcorder, digital camera, DVD play-
er, ...) to the three audio/video sockets,
located in the glove box.

Videos can only be displayed when
stationary.
Once this menu has been selected, you
can select:
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the display format, the brightness, the contrast
and the colours.


Press the "MODE" or "DARK" but-
ton to disconnect the displaying of the
video.

 Press the "SOURCE" button sev-
eral times in succession to select an
audio source other than that of the
video.
The PC Com must reinitialise and
re-start in order to change the voice
used by the voice synthesiser (male
or female) or the language used by
the system.
For safety reasons, it is imperative
that confi guration of the multifunc-
tion screens by the driver is done
only when stationary.
* According to country.

!
i
120
"Auto sequential" mode
In the automated mode, you can resume
control temporarily at any time using the
steering wheel controls.
The use of these controls permits man-
ual selection of the gears in situations
which require a more rapid change-down
than in the automated mode (arrival at
a roundabout, leaving a car park with a
steep gradient, overtaking...).
The gearbox engages the required gear if
the engine speed permits. AUTO remains
displayed on the instrument panel.
After a few minutes, the gearbox re-
sumes automatic control of the gears. "Snow" automated mode
In the automated mode, if the vehi-
cle detects poor grip, the gearbox will
change automatically to the "snow" au-
tomated mode.
Stopping the vehicle
Before switching off the engine, you can
change to position
N to be in neutral.
In this case, it is imperative that you ap-
ply the parking brake to immobilise the
vehicle.
Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised.

 Switch on the ignition. Operating fault
With the ignition on, if this warn-
ing lamp comes on and AUTO
fl ashes, accompanied by an au-
dible signal and a message on
the multifunction screen, this indicates
a gearbox malfunction.
Have it checked by a PEUGEOT dealer.
You must press the brake pedal
while starting the engine.
Never select neutral N while the
vehicle is moving.
Only engage reverse gear R when
the vehicle is immobilised, with
your foot on the brake pedal.
In all cases, it is imperative that you
apply the parking brake to immobi-
lise the vehicle.
If you press the accelerator pedal
beyond the point of resistance, the
gearbox selects the gear below to
permit sharper acceleration.

AUTO and  appear on the
instrument panel.

AUTO ,  and - appear on the
instrument panel.
 Select position N .

 Press the brake pedal.

 Wait approximately 30 seconds until

N or a gear appears on the instru-
ment panel.

 Release the brake pedal.
The gearbox is operational again.

!
!
i
122
Moving off

 Apply the parking brake.

 Select position P or N .

 Start the engine.
If this procedure is not followed, an au-
dible signal is heard, accompanied by a
message on the multifunction screen.

 With the engine running, press the
brake pedal.

 Release the parking brake.

 Select position R , D or M. ,

 Gradually release the brake pedal.
The vehicle moves off immediately.
If position N is engaged inadvert-
ently while driving, allow the engine
to return to idle then engage posi-
tion D to accelerate. The gearbox then operates in auto-
adaptive mode, without any intervention
on the part of the driver. It continuously
selects the most suitable gear accord-
ing to the style of driving, the profi le of
the road and the load in the vehicle.
For maximum acceleration without
touching the lever, press the accelera-
tor pedal down fully (kick down). The
gearbox changes down automatically
or maintains the gear selected until the
maximum engine speed is reached.
On braking, the gearbox changes down
automatically to provide effi cient engine
braking.
If you release the accelerator sharply,
the gearbox will not change to a higher
gear for safety reasons.
Automatic operation

 Select position D for automatic
changing of the four gears.

 appears on the instrument
panel.
Snow programme "
 "

 Press button "  ", after starting the
engine.
The gearbox adapts to driving on slip-
pery roads.
This programme improves starting and
drive when traction is poor.
S appears on the instrument
panel.
Sport programme "S"

 Press button "S" , after starting the
engine.
The gearbox automatically favours a
dynamic style of driving.
Never select position N while the
vehicle is moving.
Never select positions P or R unless
the vehicle is completely stationary.
When the engine is running at
idle, with the brakes released, if
position
R , D or M is selected, the
vehicle moves even without the ac-
celerator being pressed.
When the engine is running, never
leave children in the vehicle with-
out supervision.
When carrying out maintenance
with the engine running, apply
the parking brake and select posi-
tion P . Sport and snow programmes
These two special programmes supple-
ment the automatic operation in very
specifi c conditions of use.
Return to automatic operation

 At any time, press the button se-
lected again to quit the programme
engaged and return to auto-adaptive
mode.

!i
123
Stopping the vehicle
Before switching off the engine, you
can engage position P or N to place the
gearbox in neutral.
In both cases, apply the parking brake
to immobilise the vehicle. Operating fault
When the ignition is on, the light-
ing of this warning lamp, accom-
panied by an audible signal and
a message on the multifunction
screen, indicates a gearbox mal-
function.
In this case, the gearbox switches to
back-up mode and is locked in 3rd gear.
You may feel a substantial knock when
changing from P to R and from N to R .
This will not cause any damage to the
gearbox.
Do not exceed 60 mph (100 km/h), local
speed restrictions permitting.
Contact a PEUGEOT dealer as soon as
possible.
There is a risk of damage to the
gearbox:
- if you press the accelerator and brake pedals at the same time,
- if you force the movement of the gear lever from the P posi-
tion to another position when
the battery is fl at.
Manual operation

 Select position M for sequential
changing of the four gears.

 Push the lever towards the + sign to
change up a gear.

 Pull the lever towards the - sign to
change down a gear.

D disappears and the gears
engaged appear in succes-
sion on the instrument panel.
In the event of the engine la-
bouring or over-revving, the
gear selected fl ashes for a few sec-
onds, then the actual gear engaged is
displayed.
It is possible to change from position D
(automatic) to position M (manual) at
any time.
When the vehicle is stationary or mov-
ing very slowly, the gearbox selects
gear M1 automatically.
The sport and snow programmes do not
operate in manual mode. If the lever is not in position
P ,
when the driver's door is opened
or approximately 45 seconds after
the ignition is switched off, a mes-
sage appears in the multifunction
screen.

 Return the lever to position P ;
the message disappears.
It is only possible to change from one
gear to another if the vehicle speed and
engine speed permit; otherwise, the
gearbox will operate temporarily in au-
tomatic mode.
Invalid value during manual
operation
This symbol is displayed if a
gear is not engaged correctly
(selector between two posi-
tions).