2009 Peugeot 206 P Dag ignition

FAMILIARISATION EXTERIOR
Automatic switching on of the lights
This equipment switches on the side
lights and dipped headlamps when the
light is poor or when the windscreen
wipers are operating continuously,
when the lights stalk is in the "AUTO"
position.

 49
"Follow me home" lighting
This function, linked with the automatic
switching on of the lights or activated
manually, allows you to leave the front
lights on after switching off the ignition.

 48 Braking assistance systems
(ABS, EBFD and EBA)
These systems are linked and comple-
ment each other to assist you to brake
safely and effectively in emergency
situations.

 53

FAMILIARISATION
MONITOR THOROUGHLY

1. When the ignition is on, the orange
and red warning lights come on.

2. When the engine is running, these
warning lights should switch off.
If warning lights remain on, refer to the
page concerned.
Warning lights

 16
Instrument panel

A. When the ignition is on, the fuel
gauge needle should rise.

B. When the engine is running, the
associated low level warning light
should switch off.
If the levels are not correct, top up as
required.

 15 Controls

A. Passenger air bag disarming.

 58

B. Heated seats control.

 33

C. Deactivation of the ESP/ASR.

 54

D. Central locking/unlocking.

 44

FAMILIARISATION DRIVE SAFELY

1. Stop position.

2. Accessories position.

3. Ignition position.

4. Starting position.
Start

 40 Cruise control "CRUISE"

1. Cruise control mode Selection/Off.

2. Decreasing of the programmed value.

3. Increasing of the programmed value.

4. Cruise control Off/Resume.

1. Speed limiter mode Selection/Off.

2. Decreasing of the programmed value.

3. Increasing of the programmed value.

4. Speed limiter On/Off.
Speed limiter "LIMIT"

 64

 66
Adjustments must be made with the en-
gine running.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on the manual gearbox.

15
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS
Panel which groups together the vehicle operation dials and indicator lights.

4. Speedometer.
Indicates the current speed of the moving vehicle (km/h).

5. Display.

6. Display zero reset button.
Resets the selected function to zero (trip distance recorder or service
indicator).

7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instrument panel.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Fuel gauge.
Indicates the quantity of fuel remaining in the tank.

3. Cooling temperature.
Indicates the temperature of the engine coolant (°Celsius).
A. Cruise control.
Speed limiter.
(km/h)

B. Trip distance recorder.
(km)

C. Service indicator.
(km) then,
Distance recorder.
(km)
These three functions are displayed in succession when the ignition is
switched on.
For further information, refer to the sec-
tion which corresponds to the function
and to the display associated with it.
Display

!
16
The indicator/warning light comes
on continuously or fl ashes.
Some indicator/warning lights may
light in two different ways. Only by
relating the type of lighting to the
vehicle operating status can it be
ascertained whether the situation
is normal or whether a fault has oc-
curred.
Indicator and warning lights
Visual indicators which inform the driver
when a system comes into operation
(operation or deactivation indicator
lights) or of the occurrence of a fault
(warning light).
Associated warnings
The lighting of certain indicator/warning
lights may be accompanied by an audible
signal and a message on the multifunc-
tion display. Operation indicator lights
The lighting of one of the following indi-
cator lights confi rms that the correspond-
ing system has come into operation.

Left-hand direction indicator.

Handbrake applied.

Right-hand direction indicator.

Main beam headlamps.

Dipped headlamps.

Diesel engine pre-heating.
Wait until this switches off
before operating the starter.
Front fog lamps.

Rear fog lamps.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle ignition is
switched on.
When the engine is started, these warn-
ing lights should switch off.
If they remain on, before moving off,
consult the text relating to the warning
light concerned.

18
Engine autodiagnostics system.
The lighting of this warning light
indicates the occurrence of a
fault in the engine management
system.
Flashing of this warning light indicates
the occurrence of a fault in the emission
control system.
Engine oil pressure.
The lighting of this warning light
indicates the occurrence of a
fault in the engine lubrication
circuit. It is imperative that the vehicle is
stopped as soon as it is safe to do so. Battery charge.
The lighting of this warning light
indicates the occurrence of a
fault in the battery charging cir-
cuit (dirty or loose terminals, slack or
cut alternator belt, ...).
Braking.
The lighting of this warning light
indicates the occurrence of a fault
in one of the braking systems:
- signifi cant drop in the level in the circuit,
- electronic brake force distribution (EBFD) faulty (if lit at the same time
as the ABS warning light).
It is imperative that the vehicle is stopped as soon as it is safe to do so.
If the vehicle is moving, check that the
handbrake has been released fully.
Low fuel level.
The lighting of this warning light
indicates that there is enough
fuel left to drive approximately
30 miles (50 km).
The capacity of the fuel tank is approxi-
mately 50 litres. Maximum coolant
temperature.
The lighting of this warning light
indicates an excessively high
temperature in the cooling system. It is
imperative that the vehicle is stopped
as soon as it is safe to do so.
Door open.
A door, the boot or the bonnet
is still open:
Seat belt not fastened/
unfastened. The lighting of this warning light
indicates that the driver has not
fastened his seat belt or has
unfastened it.
- if the speed is below 6 mph (10 km/h),
this warning light comes on continu-
ously,
-
if the speed is above 6 mph (10 km/h),
this warning light comes on continuously,
accompanied by an audible signal.

Dynamic stability control
(ESP/ASR).
This warning light comes on for
a few seconds each time the
ignition is switched on.
When the engine is running and the
vehicle is moving, it comes on if the sys-
tem is activated.
It comes on continuously accompanied
by a message on the multifunction dis-
play when the system is deactivated.
If the warning light remains on when
the engine is running and the vehicle is
moving, contact a PEUGEOT dealer.

20
Maintenance indicator
System which informs the driver when
the next service is due, in accord-
ance with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service. More than 620 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example: 4 800 miles/km remain be-
fore the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances. Less than 620 miles (1 000 km)
remain before the next service is due

Example: 560 miles (900 km) remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains on to indicate that a service
must be carried out soon.

ii
ii
21
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into
account.
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner dis-
appears.
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes
its normal operation. The spanner
remains lit .