2009 OPEL ANTARA ad blue

70 Instruments, controls
Instruments, controls
Control indicators ............................... 70
Instrument display .............................. 75
Information display ............................ 76
Display of current tyre pressure3.... 91
Check control 3.................................. 91
Warning buzzers................................. 92
Windscreen wipers .............................. 92
Control indicators
The control indicators described here are
not present in all vehicles. The description
applies to all instrument versions.
The colours of the control indicators mean:
uABS (Anti-lock Brake System)
see page 148.
gTrailer indicator 3
Illuminates in green when a trailer is
connected to the vehicle. Extinguishes
when the trailer is disconnected.
4Brake system
Illuminates in red when ignition is switched
on. Extinguishes after engine is started.
Illuminates when engine is running if
hand brake is applied and/or fluid level for
brake hydraulics is too low.
Further information - see page 145.
z
Red Danger, important reminder,
z Yellow Warning, information, fault,
z Green Confirmation of activation,
z Blue Confirmation of activation.
9 Warning
If it illuminates when the hand brake is
not applied: stop vehicle; interrupt your
journey immediately. Consult a
workshop.

Instruments, controls73
>
Front fog lamps
Illuminates in green when front fog lamps
are switched on - see page 96.
rFog tail lamp
Illuminates in yellow when the fog tail lamp
is switched on - see page 96.
PHeadlamp main beam
Illuminates in blue when main beam is on
and when headlamp flash is operated -
see pages 14, 95.
GLow windscreen washer fluid
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates: wi ndscreen washer fluid
level low, add washer fluid as soon as
possible - see page 199.
NWater in diesel fuel filter 3
Illuminates in yellow when water level in
diesel fuel filter exc eeds a specified level.
Residual water in the diesel fuel filter will
need to be drained - see page 194 . Consult
a workshop as soon as possible.
CChange engine oil 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
Illuminates to indica te that engine oil
needs changing within approx. 1000 km
(600 miles). Engine power may be
decreased.
Once the engine oil has been changed, the
engine oil life monitor needs to be reset -
see page 194.
NPreheating for diesel engines 3
Illuminated in yellow during preheating.
Preheating system switches on only if
outside temperature is low.
If it comes on during driving or if the engine
cannot be started, consult a workshop as
soon as possible.
Starting the engine - see page 19.
IDPF (Diesel particle filter) 3
Illuminates in yellow when diesel particle
filter requires cleaning.
As soon as the road and traffic situation
permits it, increase speed to more than
50 km/h (30 mph) for approx. 15 minutes.
The control indicator extinguishes as soon
as cleaning is complete.
Further information - see page 135.
mCruise control 3
see page 140.
SEngine oil level 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates during driving;
oil level low: top up oil to specified level -
see page 192.
2Power steering
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it does not illuminate when the ignition is
switched on, stay s illuminated or
illuminates during driving, there is a fault in
the system. Consult a workshop as soon as
possible.

Lighting95
Main beam, headlamp flash
To switch from dipped beam to main
beam, push lever forwards.
To switch back to dipped beam, pull lever
back towards steering wheel.
To activate the headlamp flash, pull lever
towards steering wheel. Main beam is
engaged for the duration of activation.
The blue control indicator P is illuminated
when main beam or headlamp flash is on.
Automatic dipped beam
activation 3
Light switch to AUTO; dipped beam comes
on automatically when the engine is
running, depending on outside light
conditions.
For reasons of safety, the light switch
should always remain in the AUTO
position.
To ensure automatic dipped beam
activation functions properly, do not cover
the light sensor on top of the instrument
panel.
Turn signal lamps
To activate, press lever up or down lightly.
When the steering wheel is turned back, the
lever automatically returns to its rest
position. This will not happen when making
a minor steering manoeuvre such as lane
changing.
Tap signal: briefly move lever to resistance
point. The turn signal then flashes three
times when changing lanes or the like.
Hold the lever if you want the turn signals
to flash for longer. When released, the lever
will spring back to rest position.
The volume of the turn signal lamps’
audible warning is dependent upon vehicle
speed.
Lever up = Right turn
Lever down = Left turn

Climate control106
Heating and ventilation system
Left-hand rotary knob: Air distributionCentral rotary knob: Temperature Right-hand rotary knob: Air flow
Four fan speeds:
The rate of air flow is determined by the
fan. The fan should therefore be switched
on during driving.
M
To head area via adjustable air vents
L To head area via adjustable air vents
and to footwell
K To footwell
J To windscreen, front door windows
and footwell
l To windscreen, front door windows
and head area via adjustable air
ventsTo red = Warm
To blue = Cold
x=Off
4 = Maximum air flow

Climate control107
Ventilation
zTurn air recirculation mode 4 off.
z For maximum ventilation to head area:
set air distribution rotary knob to M.
z For ventilation to footwell:
set air distribution rotary knob to K.
z For simultaneous ventilation to head
area and footwell:
set air distribution rotary knob to L.
z Turn temperature rotary knob to blue
area for cooling.
z Set fan to desired speed.
z Open adjustable centre and side air
vents. Heating
The amount of heat is dependent on the
engine temperature and is thus not fully
attained until the engine is warm.
For rapid warming of the passenger’s
compartment:
z
Activate air recirculation mode 4.
z Set the air distribution rotary knob to
K or L .
z Turn temperature ro tary knob to red
area for warm air.
z Set fan to 4 .
z Open adjustable side air vents.
Do not use this setting for extended
periods, as gradual deterioration in air
quality and an increase in humidity may
cause windows to mist up. To obtain a temperat
ure for a "cool head
and warm feet" effect:
z Turn air recirculation mode 4 off.
z Set the air distribution rotary knob to L.
z Turn temperature rotary knob to the
middle.
z Set fan to desired speed.
z Open adjustable centre and side air
vents.
The comfort and general wellbeing of
vehicle occupants are to a large extent
dependent on a suitab le ventilation and
heating setting.

Climate control108
Heating the footwell
zSet air distribution rotary knob to K.
z Turn temperature rotary knob to red
area for warm air.
z Switch on fan. Window demisting and defrosting
To clear misted or icy
windows, e.g. due to
damp weather, damp clothing or low
outside temperatures:
z Set air distribution rotary knob to l.
z Turn temperature ro tary knob to red
area for warm air. z
Set fan to 4.
z Close centre air vents.
z Open adjustable side air vents and direct
them towards door windows.
z Switch on heated rear window Ü.
For simultaneous warming of the footwell,
set air distribution rotary knob to J.
Air conditioning n and air recirculation
4 are turned on automatically to
improve defrosting efficiency when
position J or l is selected.
To prevent windows from misting up, do
not set air distribution rotary knob to
position J or l in extremely humid
weather when temperature rotary knob is
set to blue area for cooling.
9 Warning
Failure to follow thes e instructions could
lead to misted or icy windows and
accidents stemming from impaired
visibility.

Climate control110
Cooling
Operational only with engine running and
with the fan switched on:
Control indicator in the button illuminates
when air conditioning is enabled and
extinguishes when the system is switched
off.
Cooling switches off automatically at low
outside temperatures.
Engine power and performance may be
affected when the system is on.
If the fan is switched off, the air
conditioning system will not operate. Once activated, the air conditioning
system is operated via the normal heating
and ventilation controls.
Even with air conditioning on, if
temperature rotary knob is set to warm, the
vehicle will still produce warm air in the
passenger compartment.
To improve efficiency of the air
conditioning, always close the windows,
to prevent chilled air from escaping.
Switching on the air conditioning will assist
in windscreen demisting. In very hot
temperatures, before starting the engine,
allow hot air to escape from the vehicle by
opening the windows and sun roof
3.
When the air conditioning system is
switched on, at least one of the adjustable
centre or side air vents must be open, so
that the evaporator does not ice up due to
lack of air movement.
Driving in stop-and-go traffic may reduce
the effectiveness of the air conditioning
system.
Using the air conditioning system when
driving up long hills or in heavy traffic
can cause engine overheating. If engine
coolant temperature warning control
indicator W illuminates in instrument
panel, turn off air co nditioning and allow
engine to idle for a few minutes (see
page 71). Normal cooling
z
Press button n
(to switch on air co nditioning system).
z Turn air recirculation mode 4 off.
z Set air distribution rotary knob to
position M or L.
z Turn temperature rotary knob to blue
area for cooling.
z Set fan to desired speed.
z Open air vents as required.
Press button
n=On
Press button n again = Off

Climate control111
Maximum cooling
Open windows and sun roof 3 briefly so
that warm air can escape rapidly.
z Press button n
(to switch on air co nditioning system).
z Activate air recirculation mode 4.
z Set air distribution rotary knob to M.
z Turn temperature rotary knob all the
way to blue area for cooling.
z Set fan to 4.
z Open all air vents.
Electronic Climate Control (ECC) 3
Provides the greatest amount of comfort in
the vehicle interior, regardless of the
weather, outside temperature or season.
To ensure a constant and comfortable
climate in the vehicle, the temperature of
the inflowing air, the air flow rate, air
distribution mode, air recirculation mode
and air conditioning are automatically
adapted based on the climate conditions
outside the vehicle and the current
temperature of the vehicle interior.
Temperature changes due to external
influences, such as direct sunlight, are
automatically compensated. When cooling (air conditioning
compressor) is active, air is cooled and
dehumidified.
The pollen filter removes dust, soot, pollen
and spores from the
inflowing outside air.