2009 OPEL ANTARA wheel

Instruments, controls71
rPark pilot 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it stays illuminated wh ile driving, there is
a fault in the system - see page 142.
5DCS (Descent Control System)
Both control indicators illuminate when
ignition is switched on, then extinguish.
Green
; illuminates when DCS is ready for
operation. Flashes during driving when
DCS is in operation, after pressing the
DCS button.
Yellow
; flashes to indicate system is not
ready for conditions to operate.
Illuminates to indicate there is a fault in the
system.
If the yellow control indicator flashes or
illuminates during driving, friction material
needs to cool down: drive the vehicle
without braking as much as possible.
Further information - see page 138.
BAWD (All Wheel Drive)
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it flashes during driving, the AWD system
is temporarily disabled.
If it illuminates, there is a fault in the
system. Consult a workshop as soon as
possible.
Further information - see page 121.
7ESC Active & Warning
(Electronic Stability Control)
see page 136.
AESC Not Ready
see page 136.
JESC OFF
see page 136.
qAutomatic headlamp range
adjustment 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
Comes on during drivin g to indicate a fault
that requires immediate attention. Consult
a workshop as soon as possible.
Further information - see page 97.
WCoolant temperature
Illuminates in red when ignition is
switched on, then extinguishes.
If it illuminates when the engine is running
:
stop vehicle and switch off engine. Coolant
temperature is too high; danger of engine
damage. Check coolant level.
Further information - see page 195.
9 Warning
Allow engine to cool down before
removing coolant filler cap.

Instruments, controls74
aAnti-theft alarm system activation
without monitoring of passenger
compartment and vehicle tilt 3
see page 28.
IEngine oil pressure
Illuminates in red when ignition is switched
on. Extinguishes after engine is started.
Can illuminate intermit tently when idling
with hot engine; must extinguish when
engine speed is increased.
If
it illuminates during driving;
engine oil pressure may be dangerously
low, interrupting engine lubrication and
resulting in damage to the engine and/or
locking of the driving wheels:
z Move out of the flow of traffic as quickly
as possible without impeding other
vehicles,
z Depress clutch,
z Move gearshift lever to neutral
(automatic transmission to N),
z Switch off ignition. Check engine oil level before consulting
a workshop. If the oil level is low, top up
using the specified engine oil - see pages
192, 213, 217.
If the oil level is normal, have a workshop
check the vehicle’s lubricating system.
pAlternator
Illuminates in red when ignition is switched
on. Extinguishes after engine is started.
If
it illuminates during driving:
stop vehicle and switch off engine. The
battery is not being charged and the
engine cooling may be interrupted. The
brake servo unit may cease to be effective.
Interrupt your journey immediately.
Remove key and check drive belt condition
and tensioning before consulting a
workshop.
ZExhaust emissions
Illuminates in yellow when ignition is
switched on. Extinguishes after engine is
started. Can illuminate briefly when
driving; this is normal and does not
indicate a system fault.
If it illuminates when the engine is running
;
fault in emission control system.
The permitted emission limits may be
exceeded. Fuel economy and vehicle
driveability may be impaired.
The control indicator also illuminates if
there is a fault in the diesel particle filter 3.
Consult a workshop as soon as possible.
If it flashes when the engine is running
;
for a fault that can lead to destruction of
the catalytic converter, see page 134.
Consult a workshop as soon as possible.
0Winter program 3
Illuminates in yellow when Winter program
for the automatic transmission is enabled -
see page 117.
9 Warning
When the engine is off, considerably
greater force will be required for braking
and steering.
Do not remove key until vehicle has come
to a standstill, otherwise the steering
column lock could engage unexpectedly.

Instruments, controls78
In vehicles with graphical information
display 3 or colour information display 3,
a warning message appears on the display
as a warning for icy road surfaces. There is
no message below -5 °C. Board information display,
selecting functions
Functions and settings
of some equipment
can be accessed via the board information
display.
This is done via the menus and the buttons
on the Infotainment system or with the left
adjuster wheel on the steering wheel. The
relevant menu options are then shown on
the subsequent row of the display. Select menu items using the arrow buttons:
9 Warning
Caution: the road surface may already
be icy, even though the display indicates
a few degrees above 0 °C.
Slippery road
-2,5°C
OK
11:25}21.5°C
Range
257km
OK button Select marked item,
confirm command.

Instruments, controls79
To select using the left adjuster wheel on
the steering wheel:
If check control 3 issues a warning
message, the display is blocked from other
functions. Acknowledge the message by
pressing the OK button or the left adjuster
wheel. If there are several warning
messages, acknowledge them one at a
time. Board information display,
system settings
Press the
Settings button on the
Infotainment system. Menu item Audio or
System will appear.
Press the left arrow button to reach menu
item System and select. The first function
of the System menu is marked.
Some of the functions appear on the
display in an abbreviated form. The functions are displayed in the following
order:
z
Time synchronisation
z Time, setting hours
z Time, setting minutes
z Date, setting day
z Date, setting month
z Date, setting year
z Ignition logic
z Language selection
z Setting units of measure
Turn up Previous menu item.
Turn down Next menu item.
Press Select marked item,
confirm command.
11:25}21.5°C
System

Instruments, controls81
Setting units of measureYou can select which units of measure are
to be used.
Select the menu item for units of measure
from the Settings menu and make the
desired setting. Board information display,
trip computer
3
The trip computer provides information on
driving data, which is continually recorded
and evaluated electronically.
Access trip computer vehicle data by
pressing the BC button on the Infotainment
system or the left adjuster wheel on the
steering wheel.
Some of the functions appear on the
display in an abbreviated form.
Once a function has been selected, the
subsequent rows of the trip computer
function are displayed.
The functions are displayed in the following
order:
z Instantaneous consumption
z Average consumption
z Effective consumption
z Average speed
z Distance travelled
z Range
z Stop watch Instantaneous consumptionDisplay changes depending on speed;
11:25}21.5°C
Unit Europe-SI
Display in l/h below 13 km/h.
Display in l/100 km above 13 km/h.
11:25}21.5°C
Inst. Consumpt.
7.6
l/100km

Instruments, controls82
Average consumptionDisplay of average consumption.
The measurement can be restarted at any
time – see "Resetting trip computer
information".
Effective consumption
Displays amount of fuel consumed.
The measurement can be restarted at any
time – see "Resetting trip computer
information".
Average speed
Display of average speed.
The measurement can be restarted at any
time - see "Resetting trip computer
information".
Stoppages in the journey with the ignition
off are not included in the calculations.
Distance travelled
Displays number of kilometres (miles)
driven. The measurement can be restarted
at any time – see "Resetting trip computer
information".Range
Range is calculated fr
om current fuel tank
content and instantaneous consumption.
The display shows average values.
The vehicle updates the range
automatically after a brief delay when the
vehicle has been refuelled.
If the fuel in the tank will allow less than
50 km (30 miles) of travel, the warning
"Range" appears on the display.
If the fuel in the tank will allow less than
30 km (20 miles) of travel, the warning
"Refuel!" 3 appears on the display. Resetting trip computer information
The following trip computer information
can be reset (restart measurements):
z
Average consumption
z Effective consumption
z Average speed
z Distance travelled
Select the desired trip computer
information.
Reset by pressing the left adjuster wheel on
the steering wheel or the OK button on the
Infotainment system.
11:25}21.5°C
Range
257km

Instruments, controls83
Stop watchOperating using the arrow buttons:
To start, press left arrow button to select
menu item Start and press OK button to
start/stop.
To reset, press left arrow button to select
menu item Reset and press OK button.
Operating using the left adjuster wheel on
the steering wheel:
To start, select menu item Start and press
to start/stop.
To reset, select menu item Reset and press
to confirm command. Interruption of power supply
If the power supply has been interrupted or
if the battery voltage
has dropped too low,
the values stored in the trip computer will
be lost.
Graphical information display3 or
colour information display 3,
selecting functions
The functions and settings of some
equipment 3 can be accessed via the
graphical information display or the
colour information display.
Functions are selected and executed in the
menu on the display using the arrow
buttons 3, the multifunction knob 3 on the
Infotainment system or the left adjuster
wheel on the steering wheel.
11:25}21.5°C
Stop Watch
01:22:32
h
Range257km
Aver. Consump.
7.0Ltr./100km
Inst. Consumpt.
7.6Ltr./100km
19,5° 19:36

Instruments, controls84
To select using the arrow buttons:
Select menu items via menus and with
the buttons on the Infotainment system.
If check control3 issues a warning
message, the display is blocked from other
functions. Acknowledge the message by
pressing the right or left arrow button. If
there are several warning messages,
acknowledge them one at a time. To select using the multifunction knob:
To exit a menu, turn the multifunction knob
left or right to
Return or Main and select.
If check control 3 issues a warning
message, the display is blocked from other
functions. Acknowledge the message by
pressing the multifunction knob.
If there are several warning messages,
acknowledge them one at a time. To select using the le
ft adjuster wheel on
the steering wheel:
If check control 3 issues a warning
message, the display is blocked from other
functions. Acknowledge the message by
pressing the left adjuster wheel. If there are
several warning messages, acknowledge
them one at a time.
Turn Mark menu items or
commands, select functions.
Press Select marked item, confirm
command.Turn up Previous menu item.
Turn down Next menu item.
Press Select marked item,
confirm command.