2009 OPEL ANTARA Instrument

Instruments, controls71
rPark pilot 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it stays illuminated wh ile driving, there is
a fault in the system - see page 142.
5DCS (Descent Control System)
Both control indicators illuminate when
ignition is switched on, then extinguish.
Green
; illuminates when DCS is ready for
operation. Flashes during driving when
DCS is in operation, after pressing the
DCS button.
Yellow
; flashes to indicate system is not
ready for conditions to operate.
Illuminates to indicate there is a fault in the
system.
If the yellow control indicator flashes or
illuminates during driving, friction material
needs to cool down: drive the vehicle
without braking as much as possible.
Further information - see page 138.
BAWD (All Wheel Drive)
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it flashes during driving, the AWD system
is temporarily disabled.
If it illuminates, there is a fault in the
system. Consult a workshop as soon as
possible.
Further information - see page 121.
7ESC Active & Warning
(Electronic Stability Control)
see page 136.
AESC Not Ready
see page 136.
JESC OFF
see page 136.
qAutomatic headlamp range
adjustment 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
Comes on during drivin g to indicate a fault
that requires immediate attention. Consult
a workshop as soon as possible.
Further information - see page 97.
WCoolant temperature
Illuminates in red when ignition is
switched on, then extinguishes.
If it illuminates when the engine is running
:
stop vehicle and switch off engine. Coolant
temperature is too high; danger of engine
damage. Check coolant level.
Further information - see page 195.
9 Warning
Allow engine to cool down before
removing coolant filler cap.

Instruments, controls72
o
Electronic immobiliser
Illuminates in red when ignition is
switched on, then extinguishes.
If it remains illuminated after the ignition is
on, there is a fault in the immobiliser
system; the engine cannot be started -
see page 22.
9Door open
Illuminates in red when a door is open.
3Engine electronics,
transmission electronics 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates
during driving;
there may be a fault in the engine or
transmission electronics: interrupt your
journey and consult a workshop as soon as
possible.
Further information - see page 134.
vAirbag systems 3 , belt tensioners
see pages 44, 52.
1Tailgate open
Illuminates in red when ignition is
switched on, then extinguishes.
Illuminates when tailgate is open or not
securely latched.
Tailgate - see page 26.
XDriver’s seat belt reminder
Illuminates in red when ignition is
switched on, then extinguishes.
When the engine is runn ing, if driver’s seat
belt is not engaged, it will flash for approx.
90 seconds and then illuminate until
driver’s seat belt is fastened.
If vehicle speed exceeds approx. 22 km/h
(14 mph), control indicator will flash for
approx. 90 seconds along with a warning
chime and then remains illuminated until
driver’s seat belt is fastened.
Seat belts - see page 43.
OTurn signal lamps
The relevant control indicator flashes in
green when the turn signal is on.
Rapid flash; failure of a turn signal bulb or
the corresponding fuse or failure of a trailer
turn signal bulb 3. Both control indicators
flash when the hazard warning lamps are
active.
Further information - see pages 14, 95.
Bulb replacement - see page 185.
Fuses - see page 181.
YLow fuel level
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates during dr iving; fuel level low:
fill up fuel tank as soon as possible.
Never let the tank run dry.
Erratic fuel supply can cause catalytic
converter to overheat - see page 133.
Diesel engines: if the tank has been run dry,
bleed the fuel system as described on
page 171.
Refuelling - see page 132.
Fuel tank capacity - see page 225.

Instruments, controls73
>
Front fog lamps
Illuminates in green when front fog lamps
are switched on - see page 96.
rFog tail lamp
Illuminates in yellow when the fog tail lamp
is switched on - see page 96.
PHeadlamp main beam
Illuminates in blue when main beam is on
and when headlamp flash is operated -
see pages 14, 95.
GLow windscreen washer fluid
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates: wi ndscreen washer fluid
level low, add washer fluid as soon as
possible - see page 199.
NWater in diesel fuel filter 3
Illuminates in yellow when water level in
diesel fuel filter exc eeds a specified level.
Residual water in the diesel fuel filter will
need to be drained - see page 194 . Consult
a workshop as soon as possible.
CChange engine oil 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
Illuminates to indica te that engine oil
needs changing within approx. 1000 km
(600 miles). Engine power may be
decreased.
Once the engine oil has been changed, the
engine oil life monitor needs to be reset -
see page 194.
NPreheating for diesel engines 3
Illuminated in yellow during preheating.
Preheating system switches on only if
outside temperature is low.
If it comes on during driving or if the engine
cannot be started, consult a workshop as
soon as possible.
Starting the engine - see page 19.
IDPF (Diesel particle filter) 3
Illuminates in yellow when diesel particle
filter requires cleaning.
As soon as the road and traffic situation
permits it, increase speed to more than
50 km/h (30 mph) for approx. 15 minutes.
The control indicator extinguishes as soon
as cleaning is complete.
Further information - see page 135.
mCruise control 3
see page 140.
SEngine oil level 3
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it illuminates during driving;
oil level low: top up oil to specified level -
see page 192.
2Power steering
Illuminates in yellow when ignition is
switched on, then extinguishes.
If it does not illuminate when the ignition is
switched on, stay s illuminated or
illuminates during driving, there is a fault in
the system. Consult a workshop as soon as
possible.

Instruments, controls74
aAnti-theft alarm system activation
without monitoring of passenger
compartment and vehicle tilt 3
see page 28.
IEngine oil pressure
Illuminates in red when ignition is switched
on. Extinguishes after engine is started.
Can illuminate intermit tently when idling
with hot engine; must extinguish when
engine speed is increased.
If
it illuminates during driving;
engine oil pressure may be dangerously
low, interrupting engine lubrication and
resulting in damage to the engine and/or
locking of the driving wheels:
z Move out of the flow of traffic as quickly
as possible without impeding other
vehicles,
z Depress clutch,
z Move gearshift lever to neutral
(automatic transmission to N),
z Switch off ignition. Check engine oil level before consulting
a workshop. If the oil level is low, top up
using the specified engine oil - see pages
192, 213, 217.
If the oil level is normal, have a workshop
check the vehicle’s lubricating system.
pAlternator
Illuminates in red when ignition is switched
on. Extinguishes after engine is started.
If
it illuminates during driving:
stop vehicle and switch off engine. The
battery is not being charged and the
engine cooling may be interrupted. The
brake servo unit may cease to be effective.
Interrupt your journey immediately.
Remove key and check drive belt condition
and tensioning before consulting a
workshop.
ZExhaust emissions
Illuminates in yellow when ignition is
switched on. Extinguishes after engine is
started. Can illuminate briefly when
driving; this is normal and does not
indicate a system fault.
If it illuminates when the engine is running
;
fault in emission control system.
The permitted emission limits may be
exceeded. Fuel economy and vehicle
driveability may be impaired.
The control indicator also illuminates if
there is a fault in the diesel particle filter 3.
Consult a workshop as soon as possible.
If it flashes when the engine is running
;
for a fault that can lead to destruction of
the catalytic converter, see page 134.
Consult a workshop as soon as possible.
0Winter program 3
Illuminates in yellow when Winter program
for the automatic transmission is enabled -
see page 117.
9 Warning
When the engine is off, considerably
greater force will be required for braking
and steering.
Do not remove key until vehicle has come
to a standstill, otherwise the steering
column lock could engage unexpectedly.

Instruments, controls75
Instrument display
Tachometer
Making use of the tachometer helps to
save fuel; it indicates the engine speed in
revolutions per minute (rpm).
Red warning zone on right; maximum
permissible engine speed exceeded,
danger to engine.
If possible, drive in each gear in the low
engine speed range (between approx.
2000 and 3000 rpm) and maintain an even
vehicle speed to maximise fuel efficiency. Speedometer
Indicates the vehicle speed.
Odometer
The odometer indicates how far the vehicle
has been driven.
Trip odometer
There are two independent trip odometers
which indicate how far the vehicle has been
driven since the last reset.
Press the trip odometer button once to
toggle between
Trip A and Trip B .
To reset a trip odometer, press and hold
the trip odometer button.

Instruments, controls76
Fuel gauge
Indicates fuel level when the ignition is on.
After adding fuel and restarting engine,
fuel gauge pointer slowly moves to show
new fuel level.
When fuel gauge indica tes that fuel supply
is low, control indicator
Y illuminates:
fill up fuel tank as soon as possible -
see page 132.
Never let the fuel tank become empty.
Diesel engines: if the tank has been run dry,
bleed the fuel system as described on
page 171.
Because of the amount of fuel remaining in
the tank, the amount of fuel required to fill
the tank may be less than the specified
tank capacity. Transmission display 3
Display of the selected gear or mode with
automatic transmission
3.
Information display
Board information display
Display of time, outside temperature and
date/Infotainment system (when it is on).
An F in the display in dicates a fault.
Have the cause of the fault remedied by a
workshop.
P Park position.
R Reverse gear.
N Neutral.
D Automatic mode.
1 to 5 Selected gear in manual
mode.
11:25}21.5°C
Range
RDS [TP]
257km

Instruments, controls77
Graphical information display3,
colour information display 3
Display of time, outs ide temperature, and
date/Infotainment system (when it is on).
The graphical information display presents
the information in monochrome. The colour
information display presents the
information in colour. The type of information and how it is
displayed depends on the equipment of
the vehicle and the settings of the trip
computer
3 and Infotainment system.
Some information appears on the display
in an abbreviated form.
Infotainment system – see Infotainment
system instruction manual.
An F in the display indicates a fault.
Have the cause of the fault remedied by a
workshop.Outside temperature
A fall in temperature is indicated
immediately and a rise in temperature
after a time delay.
If outside temperature drops to 3 °C,
the symbol : illuminates in the board
information display as a warning for
icy road surfaces. : remains illuminated
until outside temperature reaches at
least 5 °C.
Range257km
Aver. Consump.
7.0Ltr./100km
Inst. Consumpt.
7.6Ltr./100km
19,5° 19:36
:
11:25}-1.5°C
Range
RDS[TP]
257km

Instruments, controls78
In vehicles with graphical information
display 3 or colour information display 3,
a warning message appears on the display
as a warning for icy road surfaces. There is
no message below -5 °C. Board information display,
selecting functions
Functions and settings
of some equipment
can be accessed via the board information
display.
This is done via the menus and the buttons
on the Infotainment system or with the left
adjuster wheel on the steering wheel. The
relevant menu options are then shown on
the subsequent row of the display. Select menu items using the arrow buttons:
9 Warning
Caution: the road surface may already
be icy, even though the display indicates
a few degrees above 0 °C.
Slippery road
-2,5°C
OK
11:25}21.5°C
Range
257km
OK button Select marked item,
confirm command.