2009 OPEL AGILA service

5-9Instruments and controls
X Driver’s seat belt
Will illuminate in red when ignition is
switched on if driver’s seat belt is not
engaged.
If vehicle speed exceeds 15 km/h
(9 mph) and driver’s seat belt is not
engaged, the control indicator will
flash for approx. 90 seconds along
with a warning chime and then
illuminate until driver’s seat belt is
fastened correctly.
Seat belts 3 3-5.
v Airbag systems, belt
tensioners
Will flash in red several times when
the ignition is switched on, then
extinguish.
If it does not flash when the ignition is
switched on, stays lit, illuminates or
flashes whilst driving, there is a fault
with the airbag systems or with the
belt tensioners. The systems might
not therefore be triggered in the event
of an accident. Seek the assistance
of a workshop immediately.
Belt tensioners 3 3-6, airbags 3 3-13.
p Charging system
Will illuminate in red when ignition is
switched on. Extinguishes after
engine is started.
If it stays lit after the ignition is
switched on or illuminates during
driving: stop vehicle and switch off
engine. The battery is not being
charged and the engine cooling may
be interrupted. The brake servo unit
may cease to be effective. Interrupt
your journey immediately.
Remove ignition key and check drive
belt condition and tensioning before
seeking the assistance of a
workshop.
s Service transmission 3
Will illuminate briefly in yellow when
the ignition is switched on.
If it flashes, there is a fault in the
automatic transmission. Seek the
assistance of a workshop
immediately.
Automatic transmission 39-3.
R Brake system
Will illuminate in red when ignition is
switched on. Extinguishes after
engine is started.
Illuminates when engine is running if
parking brake is applied and/or fluid
level for brake hydraulics is too low.
Further information 3 9-9,
brake fluid level 3 10-6.
u Anti-lock Brake System
(ABS)
Will illuminate briefly in yellow when
ignition is switched on.
At the same time, the system
performs a self-check. When the
control indicator extinguishes, the
system is ready for operation.
Caution
If it illuminates when the parking
brake is not applied: stop vehicle;
interrupt your journey immediately.
Seek the assistance of a workshop.

5-12 Instruments and controls
„Depress clutch,
„Move gearshift lever to neutral
(automatic transmission 3 to N),
„Switch off ignition.
Check engine oil level. If the oil level
is low, top up using the specified
engine oil 3 10-3, 11-6, 12-3.
If the oil level is normal, seek the
assistance of a workshop to have the
vehicle’s lubricating system checked.
I Engine oil life monitor 3
For engines with diesel particle filter.
Will flash in red when engine oil and
filter require changing.
Engine oil life monitor 3 3 5-14.o
Theft-deterrent
Will start flashing slowly in red after
the key is turned to positions LOCK or
ACC, or removed from the ignition
switch.
o Immobiliser
Control indicator o (or A for diesel
engines) illuminates when the ignition
is switched on, and extinguishes
when the engine is started.
If either control indicator flashes after
the ignition is switched on, there may
be a fault in the immobiliser system;
the engine cannot be started 3 2-7.
> Front fog lamps 3
Control indicator in button >, located
on the lower instrument panel,
illuminates when front fog lamps are
switched on 3 6-3.
r Rear fog lamp
Will illuminate in yellow when the rear
fog lamp is switched on 3 6-3.
P High beam
Will illuminate in blue when the high
beam is on and when headlamp flash
is operated 3 6-2.
q Headlamp range
adjustment 3
Will illuminate during driving to
indicate a fault that requires
immediate attention. Seek the
assistance of a workshop as soon as
possible.
Further information 3 6-1.
9 Door ajar 3
Will illuminate in red when a door or
the tailgate is open.
A Service vehicle soon
(for diesel engines) 3
Will illuminate briefly in yellow when
ignition is switched on.
If it flashes when the ignition is
switched on, there may be a fault in
the immobiliser system; the engine
cannot be started (3 “o Immobiliser“,
3 2-7).
9 Warning
When the engine is off,
considerably greater force will be
required for braking and steering.
Do not remove key until vehicle
has come to a standstill,
otherwise the steering column
lock could engage unexpectedly.

5-13Instruments and controls
If it illuminates when the engine is
running; there may be a fault in the
engine electronics: interrupt your
journey and seek the assistance of a
workshop.
If regeneration of the diesel particle
filter is not successful or possible (3
5-13 “8 Diesel particle filter 3“), the
control indicator may illuminate and
the vehicle goes into limp home
mode: interrupt your journey and
seek the assistance of a workshop
immediately.
Further information 3 9-7.
Y Low fuel
If it illuminates during driving; fuel
level is low: fill up fuel tank as soon
as possible.
Never let the tank run dry!
Erratic fuel supply can cause catalytic
converter to overheat 3 9-8.
Diesel engines: The engine stops and
control indicator Z illuminates if the
fuel level is too low (3 5-11 “Z
Exhaust emissions”). If the tank has
been run dry, bleed the fuel system 3
10-7.Refuelling 3 9-12, fuel tank capacity
3 12-5.
8 Diesel particle filter 3
Will illuminate briefly in yellow when
the ignition is switched on.
If it illuminates during driving, the
diesel particle filter requires cleaning.
As soon as the road and traffic
situation permits it, increase speed to
more than 75 km/h (50 mph) for
approx. 30 minutes. The control
indicator extinguishes as soon as
cleaning is complete.
If regeneration of the diesel particle
filter is not successful or possible (3
5-12 “A Service vehicle soon 3“),
control indicator A may illuminate
and the vehicle goes into limp home
mode: interrupt your journey and
seek the assistance of a workshop
immediately.
Further information 3 9-7.
O Turn signal lamps
The appropriate control indicator will
flash in green when the turn signal is
on. Rapid flash; failure of a turn signal
bulb or the corresponding fuse.
Both control indicators flash when the
hazard warning lamps are active.
Turn signal lamps 3 6-2, bulb
replacement 3 10-7, fuses 3 10-11.
Warning chimes
While driving:
„when operating the turn signals.
„if driver’s seat belt is not engaged
and vehicle speed exceeds approx.
15 km/h (9 mph).
When the vehicle is parked and
driver’s door is opened:
„with exterior lamps switched on
(and ignition key removed).
„when the key is in the ignition
switch.
Seat belt warning chime 33-7.
Driving hints 3 9-1.

5-14 Instruments and controls
Service interval display 3
In the case of vehicles with fixed
engine oil change and service
intervals, InSP appears in the
odometer display if the ignition is
switched on when servicing is
overdue: have the next service
carried out within one week or
500 km (300 miles). Seek the
assistance of a workshop.
After the service is complete, have
the display reset by a workshop.
Engine oil life monitor 3
Indicates when the engine oil and oil
filter require changing. Based on
driving conditions, the interval at
which an oil change will be indicated
can vary considerably.
When the system has calculated that
oil life has been diminished, control
indicator
I flashes in the instrument
cluster when the engine is running.
Engine oil and oil filter need changing
immediately. Engine power may be decreased. For
the system to work properly, it must
be reset every time the engine oil and
oil filter are changed: seek the
assistance of a workshop.
Trip computer 3
The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.
To access trip computer vehicle data:
With the ignition switched on, press
the MODE button repeatedly 3 5-6
until instantaneous fuel consumption,
average fuel consumption (AVG.) or
fuel range (RANGE) appears in the
odometer display.

7-7Infotainment system
If less than 6 stations with strong
signals can be received, the number
of preset stations may be less than 6.
If no stations with strong signals can
be received, previously stored
stations are reset.
When automatic storing is complete,
the radio station stored under preset
station memory location 1 is
received.
To exit automatic storing while storing
is in progress, press the AST
button4 again. Previously stored
stations are not overwritten.
Recalling stored stations
To recall a station stored under one of
the preset station memory locations
1-6, tune to the desired waveband
and press the relevant preset station
button (1-6). The station
corresponding to the preset station
button is received.
If a station is not stored on the
selected preset station button (1-6),
“- - -” will appear in the display.RDS (Radio Data System)
RDS is a European service provided
by broadcasting companies, which
makes finding the required FM station
much easier and aids good reception.
RDS stations transmit information
which is automatically evaluated by
the RDS radio.
In some areas, other functions
associated with RDS are available,
e.g. TA (Traffic Announcement) and
REG (Regionalisation).
AF (Alternative Frequency)
An RDS program is transmitted on
several frequencies simultaneously.
With AF on, during the journey the
Infotainment system automatically
searches for the strongest receivable
frequency.
REG (Regionalisation)
Some RDS stations transmit different
regional programs over different
frequencies at certain times.
With REG on, when searching for the
frequency of a radio program with the
strongest reception using AF (Alternative Frequency), the
Infotainment system always remains
tuned to the selected regional
program.
With REG off, when searching for the
frequency of a radio program with the
strongest reception using AF
(Alternative Frequency), the
Infotainment system does not
consider regional programs.
Switching AF and REG on and off
Settings appears in the following
order when the AF button 7 is
pressed repeatedly:
„AF on/REG off,
„AF on/REG on,
„AF off, REG off.
With AF and/or REG active, “AF” and
“REG” appear in the display
respectively.PTY (Program Type)
Many RDS stations transmit a PTY
code that indicates the type of
program being broadcast

7-8 Infotainment system
(e.g. News). The PTY code enables
selection of the station according to
program type.
Searching for stations by
program type
Press the PTY button 8 to select
PTY mode.
Turn the bVOLUME rotary knob f
to select the desired PTY (e.g. News,
Sports).
Press the hbutton j or
gbuttoni to begin search within
the selected PTY.
If no station within the selected PTY
code is received, “NOTHING”
appears in the display followed by
“PTY”. Select another PTY as
described above.
TA (Traffic Announcement)
Traffic stations are RDS stations
which transmit traffic information.
With TA on, the Infotainment system
searches for stations emitting TP
(Traffic Programs) and tunes into
such stations in preference to others.When TA is active and a Traffic
Program is currently being received,
CD/MP3 CD 3 playback is
interrupted for the traffic
announcement and is resumed when
the announcement ends.
Switching TA on and off
Press the TA button 9 to switch on
traffic announcements.
With TA active, “TA” appears in the
display. When a Traffic Program is
currently being received, “TP” also
appears in the display.
Press the TA button 9 again to
switch off traffic announcements.
To search for a TP station (TP SEEK)
while TA is active, press the
hbuttonj or gbutton i.
If TP data is not received within
approx. 20 seconds after TA is
switched on, TP SEEK automatically
takes place only once.
If no TP station is received,
“NOTHING” appears in the display.
PS (Program Service Name)
Display of program name instead of
station frequency.
EON (Enhanced Other
Networks)
With EON, you will hear traffic
reports, even if the set station does
not transmit its own traffic
information. When a traffic
announcement is made, the unit
switches to a traffic information
station linked to EON.
When EON is active, “EON” appears
in the display.

7-10 Infotainment system
Selecting next or previous MP3
folder3
If the MP3 CD consists of several
folders, the required folder can be
selected as follows:
Press the DISC/FLD + button c to
skip to the next folder.
Press the - DISC/FLD button d to
skip back to the previous folder.
Displaying MP3 text
MP3 text types appear in the
following order when the TEXT
buttona is pressed repeatedly:
„Elapsed time,
„Folder name,
„File name.
Press and hold the TEXT buttona
for approx. 2 seconds to enable
scrolling text.
Removing CDs
Press the f button 1.
The CD is ejected.
Maintenance and care
„Never insert foreign objects in the
CD slot.
„If “ERROR 1” appears in the
display, the disc cannot be read. If
a normal, undamaged disc is
inserted and the message remains,
seek the assistance of a workshop.
„If “ERROR 3” appears in the
display, the player has developed
an unidentified error. The inserted
disc may not eject. Seek the
assistance of a workshop.
„Do not use commercially available
CD protection sheets or discs
equipped with stabilisers, as they
may get trapped in the internal
mechanism.
„Do not use any abrasive chemicals,
cleaning solutions or strong
cleaners. Use only a soft cloth
moistened with soapy water.
„The system must only be serviced
by trained specialists. Faulty
installation or servicing may
invalidate the unit’s warranty.Mobile telephones and
radio equipment (CB) 3
Installation and operation
The Opel installation instructions and
the operating guidelines provided by
the telephone manufacturer must be
observed when fitting and operating a
mobile telephone.
Failure to do so could invalidate the
vehicle’s operating permit
(EU Directive 95/54/EG).
Requirements to ensure trouble-free
operation:
„Professionally installed exterior
antenna, to obtain the maximum
range possible
„Maximum transmission power
10 Watts.
„Installation of the telephone in a
suitable spot (front centre console).
Obtain advice on predetermined
installation locations for the external
antenna and equipment holder and
ways of using devices with
transmission power of more than
10 Watts.

8-6Climate controls
Maintenance
Air intake
The air intakes in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Pollen filter
The pollen filter cleans dust, soot,
pollen and spores from the air
entering from outside. Replace the pollen filter at the
intervals given in the chapter “Service
and maintenance” 311-2.