2009 OPEL AGILA ECO mode

5-3Instruments and controls
Windscreen washer system
To activate, pull lever towards
steering wheel. Washer fluid is
sprayed onto the windscreen.
In vehicles with timed interval wipe
position INT 3, the wipers switch on
automatically at low speed if they are
not already activated.
Rear window wiper/washer
To activate wiper and washer, rotate
end of lever:
Washer fluid is sprayed on to rear
window when the end of the lever is
turned to position
f. When the lever
is released, it will spring back to the
ON/OFF position.Further information 3 10-5, 10-30,
10-31.
Clock
The time is shown in the odometer
display when the ignition is switched
on.
Correcting time
To set the clock, press and hold the
Öbutton for approx. 2 seconds; clock
display now in setting mode. f=Washer
ON = Wiper on
INT = Timed interval wipe 3
OFF = Wiper off
f=Washer
Minute display flashes.
Press Ö to set minutes.

5-6 Instruments and controls
Odometer
The odometer indicates how far the
vehicle has been driven.
Trip odometer
There are two independent trip
odometers which indicate how far the
vehicle has been driven since the last
reset.
Press the MODE button repeatedly
until A or B appears on the left of the
odometer display. To reset a trip odometer, press and
hold the MODE button for approx.
2 seconds while the relevant trip
odometer is displayed.
Odometer display brightness
To change brightness level, switch on
headlamps and press the MODE
button repeatedly until the squares
that indicate the brightness level
appear in the odometer display. Then
press and hold the MODE button to
cycle through brightness levels.Four squares indicates maximum
brightness, while one square
indicates the minimum brightness
level.
Tachometer
Indicates the engine speed.
Caution
Pointer in warning zone; maximum
permissible engine speed
exceeded, danger to engine.

5-7Instruments and controls
Fuel gauge
Indicates fuel level when the ignition
is on (F indicates full, E indicates
empty).
When fuel gauge indicates that fuel
supply is low (one segment on the
gauge is illuminated), fill up fuel tank
as soon as possible. If control
indicator
Y illuminates in the
instrument cluster, refuel
immediately.
Never let the fuel tank become
empty. Diesel engines: if the tank has
been run dry, bleed the fuel system
310-7.Because of the amount of fuel
remaining in the tank, the amount of
fuel required to fill the tank may be
less than the specified tank capacity.
Refuelling 39-12.
Transmission display 3
Display of the selected gear or mode
with automatic transmission.Automatic transmission 39-3.
P Park position
R Reverse gear
N Neutral
D Automatic mode
3, 2, L Selected gear

5-14 Instruments and controls
Service interval display 3
In the case of vehicles with fixed
engine oil change and service
intervals, InSP appears in the
odometer display if the ignition is
switched on when servicing is
overdue: have the next service
carried out within one week or
500 km (300 miles). Seek the
assistance of a workshop.
After the service is complete, have
the display reset by a workshop.
Engine oil life monitor 3
Indicates when the engine oil and oil
filter require changing. Based on
driving conditions, the interval at
which an oil change will be indicated
can vary considerably.
When the system has calculated that
oil life has been diminished, control
indicator
I flashes in the instrument
cluster when the engine is running.
Engine oil and oil filter need changing
immediately. Engine power may be decreased. For
the system to work properly, it must
be reset every time the engine oil and
oil filter are changed: seek the
assistance of a workshop.
Trip computer 3
The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.
To access trip computer vehicle data:
With the ignition switched on, press
the MODE button repeatedly 3 5-6
until instantaneous fuel consumption,
average fuel consumption (AVG.) or
fuel range (RANGE) appears in the
odometer display.

5-15Instruments and controls
Instantaneous consumption
Display of instantaneous fuel
consumption.
Until the vehicle is moving, “--.-”
appears in the display.
Average consumption
Display of average fuel consumption.
The measurement can be restarted at
any time.
To reset: With average consumption
showing in the display, press and
hold the MODE button for approx.
2 seconds. The display will show
“--.-” briefly and the average
consumption figure will update after a
delay.
Range
Range is calculated from current fuel
tank content and instantaneous
consumption. The display shows
average values.
The range is updated automatically
after a brief delay when the vehicle
has been refuelled.
When the vehicle is being driven,
“--.-” appears in the display when fuel
level is low: fill up fuel tank as soon as
possible.

5-16 Instruments and controls
If control indicator Y illuminates in the
instrument cluster, refuel
immediately, regardless of the value
shown in the range display.
Setting units of measure
You can select which units of
measure are to be used for fuel
consumption figures.
With the vehicle stationary and with
instantaneous consumption showing
in the display, press and hold the
MODE button for approx. 2 seconds
to toggle between L/100km and
km/L.
Interruption of power supply
If the power supply has been
interrupted or if the battery voltage
has dropped too low, the values
stored in the trip computer will be lost.

7-3Infotainment system
To search for the next or previous
radio station:
Press and hold the hbutton (higher
frequency) or gbutton (lower
frequency).
To select the next or previous preset
station:
Briefly press the hbutton (next
stored station) or gbutton (previous
stored station).
With CD mode active, to select the
next or previous track:
Press the hbutton (next track) or
gbutton (previous track).
Theft-deterrent feature
The Infotainment system is fitted with
an electronic security system for anti-
theft protection, ensuring the system
is useless to a thief.
You can set up a 4-digit security ID to
prevent theft. Once the ID is set up,
the unit is inoperable without this ID
when the unit is removed or the
battery is disconnected.
The Infotainment system is
programmed with the default code
‘0000’ in the as-delivered state.Setting 4-digit security ID
To set a user ID, proceed as follows:
The user ID is now required when the
Infotainment system is switched on
after the unit has been removed or
the battery has been disconnected. 1. Briefly press the bVOLUME
rotary knobf to switch the
Infotainment system off.
2. Press and hold the numbered
button 30 and button 4d
simultaneously and press the
bVOLUME rotary knobf.
“SEC” appears in the display.
3. Press the h button j and
numbered button 1e
simultaneously.
“- - - -” appears in the display.4. Press numbered button 1e
repeatedly to increase the value
for the first user ID digit.
Likewise, numbered buttons
2b, 30 and 4d
correspond to the second, third
and fourth digits of the user ID.
Set each user ID digit by
pressing the corresponding
numbered button repeatedly
until your chosen user ID is
complete.
5. Press and hold the PTY
button8 for approx.
2 seconds to enter your chosen
user ID.
“SEC” appears again in the
display and the Infotainment
system is switched off
automatically.

7-4 Infotainment system
Entering 4-digit security ID
When the Infotainment system is
switched on after the unit has been
removed or the battery has been
disconnected, the 4-digit security ID
must be entered, otherwise the unit is
inoperable.
“SEC” appears in the display when
the system is switched on. This will
not happen if the system is switched
off and back on again within
20 seconds.
To enter the user ID, proceed as
follows:Switch the Infotainment system back
on to operate: the system comes on
in radio mode.
If the wrong user ID is entered
10 times, “HELP” appears in the
display and the system cannot be
operated. Seek the assistance of a
workshop.
If you forget your user ID, seek the
assistance of a workshop.
Deleting 4-digit security ID
The stored user ID can be erased and
a new ID set at any time.To delete the existing user ID, repeat
steps 1 to 3 in “Setting 4-digit
security ID” then proceed as follows:
Set a new user ID as described in
“Setting 4-digit security ID”.
Operation
Switching on and off
Briefly press the bVOLUME rotary
knob f.
Setting the volume
Turn the bVOLUME rotary knob f. 1. Press the h button j and
numbered button 1e
simultaneously.
“- - - -” appears in the display.
2. Repeatedly press numbered
buttons 1e, 2b, 30 and
4d which correspond to the
digits of the user ID, until the
correct stored user ID is
displayed.3. Press and hold the PTY
button8 for approx.
2 seconds to enter the correct
stored user ID.
The Infotainment system is
switched off automatically.1. Repeatedly press numbered
buttons 1e, 2b, 30 and
4d which correspond to the
digits of the user ID, until the
correct stored user ID is
displayed.
2. Press and hold the PTY
button8 for approx.
2 seconds to enter the correct
stored user ID.
“- - - -” appears in the display
and the Infotainment system is
switched off automatically.