2009 NISSAN GT-R parking brake

Black plate (121,1)
Model "R35-D" EDITED: 2008/ 5/ 20
position when you leave the vehicle
for extended periods of time, other-
wise the battery will be discharged.
. Never leave the light switch on
when the engine is not running for
extended periods of time even if the
headlights turn off automatically.
Daytime running light system (Ca-
nada only)The daytime running lights automatically illumi-
nate when the engine is started with the parking
brake released. The daytime running lights
operate with the headlight switch in the OFF
position. Turn the headlight switch to theposition for full illumination when driving at night.
If the parking brake is applied before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illuminate
once the parking brake is released. The daytime
running lights will remain on until the ignition
switch is pushed to the OFF position.
WARNING
When the daytime running light system
is active, tail lights on your vehicle are
not on. It is necessary at dusk to turn on
your headlights. Failure to do so could
cause an accident injuring yourself and
others.
Turn signalMove the lever up or down to the position
*1
to
signal the turning direction. When the turn is
completed, the turn signals cancel automatically.
Lane change signalTo indicate a lane change, move the lever up or
down to the position
*2
where the lights begin
flashing.
Instruments and controls
2-49
,QIRUPDWLRQ3URYLGHGE\

Black plate (19,1)
5 Starting and driving
Model "R35-D" EDITED: 2008/ 5/ 20
Precautions when starting and driving..................... 5-2
Exhaust gas (Carbon monoxide) ........................ 5-2
Three-way catalyst .......................................... 5-2
Tire Pressure Monitoring System (TPMS) ............. 5-3
Avoiding collision and rollover ........................... 5-5
Off-road recovery ........................................... 5-6
Rapid air pressure loss .................................... 5-6
Drinking alcohol/drugs and driving ...................... 5-7
All-Wheel Drive (AWD) driving safety
precautions ................................................... 5-7
Push-button ignition switch .................................. 5-8
Operating range for engine start ........................ 5-8
Ignition switch operation .................................. 5-8
Ignition switch positions ................................... 5-9
Intelligent Key battery discharge ...................... 5-10
Before starting the engine .................................. 5-11
Starting the engine ........................................... 5-11
Driving the vehicle ............................................ 5-13
Dual clutch transmission ................................ 5-13
Driving tips ................................................. 5-19
VDC, transmission and suspension setup
switches ........................................................ 5-21
How to switch the modes .............................. 5-22
Features of each mode .................................. 5-23
Turbocharger system ......................................... 5-26
Parking brake .................................................. 5-27 Cruise control
................................................. 5-28
Precautions on cruise control .......................... 5-28
Steering-wheel-mounted controls ..................... 5-29
Indicators and display ................................... 5-29
Cruise control operations ............................... 5-29
Hill Start Assist ................................................ 5-31
Break-in schedule ............................................ 5-32
Increasing fuel economy .................................... 5-33
All-Wheel Drive (AWD) ..................................... 5-34
AWD warning light ....................................... 5-34
Tight corner braking phenomenon .................... 5-35
Tires ......................................................... 5-35
AWD system characteristics ........................... 5-35
Limited Slip Differential (LSD) ............................. 5-36
Parking/parking on hills ...................................... 5-37
Power steering ................................................ 5-38
Brake system .................................................. 5-38
Braking precautions ...................................... 5-38
Parking brake break-in ................................... 5-39
Brake assist .................................................... 5-39
Anti-lock Braking System (ABS) ...................... 5-39
Vehicle Dynamic Control (VDC) system ................. 5-40
Cold weather driving ......................................... 5-42
Freeing a frozen door lock .............................. 5-42
Anti-freeze .................................................. 5-42
Battery ...................................................... 5-42
,QIRUPDWLRQ3URYLGHGE\

Black plate (182,1)
Model "R35-D" EDITED: 2008/ 5/ 20
1. Check the positions of the accelerator pedal
*1
and brake pedal
*2. Adjust the steering
wheel and seat positions so that the correct
driving posture is achieved. (
“FRONT
SEATS” page 1-2)
2. Check that the parking brake is engaged.
3. Check that the shift lever is in the&Por&N
position. (
&Pis recommended.)
4. Firmly depress the brake pedal. Without depressing the accelerator pedal, press the
ignition switch once to start the engine.
5. To stop the engine, move the shift lever to the
&Pposition, and push the ignition switch
to the OFF position.
NOTE:. If the engine is difficult to start, de-
press the accelerator pedal all the way
to the floor and hold it. Push the
ignition switch with the brake pedal
depressed to start cranking the engine.
After 5 or 6 seconds, stop cranking by
pushing the ignition switch to the OFF
position, and then release the accel-
erator pedal. Then perform steps 1 to 4
to start the engine. If the engine starts,
but fails to run, repeat this procedure.
. Starting and stopping the engine over a
short period of time may make the
vehicle more difficult to start. If this
occurs, wait for more than 3 minutes,
and then press the ignition switch
again to start the engine.
. To maintain high performance over a
long period of time, the engine speed is
limited to 5,000 rpm when the engine is
revved with the shift lever in the
&Nor
&Pposition, and to 4,000 rpm when the
engine oil or coolant temperature is
low or higher than normal.
. If the ignition switch is pressed before
the shift lever is moved to the
&P
position, the ignition switch will not
change to the OFF position. If this occurs, the SHIFT
&P
warning display
appears on the vehicle information
display. When stopping the engine, be
sure to move the shift lever to the
&P
position and then press the ignition
switch. Failure to do so may result in
discharge of the battery. (
“SHIFT
“P” WARNING” page 2-40)
. If the shift lever was in the
&A↔&Mor
&R
position when the engine was stopped,
then be sure to move the shift lever to
the
&P
position before starting the
engine the next time. If the engine is
started with the shift lever in the
&N
position, then it may not be possible to
drive the vehicle even when the shift
lever is moved to the
&A↔&M
or
&R
position. If this occurs, the SHIFT
&P
warning appears on the vehicle infor-
mation display. (
“SHIFT “P”
WARNING” page 2-40)
CAUTION
If the engine was stopped soon when
the engine is hot, the cooling fan may
operate for approximately 2 minutes
after the engine was stopped to cool
the components in the engine compart-
5-12
Starting and driving
,QIRUPDWLRQ3URYLGHGE\

Black plate (185,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Shift lever operation
Push the button while depressing the brake
pedal.Push the button.Just move the shift lever.Automatically returns.
&Pposition:
Use this position for parking and starting the
engine. The ignition switch will be changed to
the OFF or LOCK position.
CAUTION
Use the
&P
position only when the
vehicle is completely stopped.
&Rposition:
Use this position for driving in reverse.&Nposition:
Neither forward nor reverse gear is engaged.&A↔&M
position:
Use this position for all normal forward driving.
The shift lever can be moved between
&Aand
&M
to alternately change each other. The position indicator indicates the gear position
with the indication of “A” or “M”.
.
&A
position: Use this position for ordinary
driving, with the gears shifted automatically
from first gear to sixth gear according to the
speed and driving conditions.
.
&M
position: Operate the paddle shifter to
drive in first gear to sixth gear as desired.
CAUTION
Grip the shift lever correctly when
operating it. Failure to do so may cause
a finger or other items to be trapped
between the lever and gate, possibly
causing an accident.
NOTICE
. Be sure to observe the following
precautions. Failure to do so may
result in shift lever malfunction.
— Do not spill water, beverages or
other liquids on the shift lever.
Starting and driving
5-15
,QIRUPDWLRQ3URYLGHGE\

Black plate (186,1)
Model "R35-D" EDITED: 2008/ 5/ 20
— Do not allow sand or similarsubstances to contact the shift
lever.
. Develop the habit of performing the
operations marked with “
”
without pressing the button. If the
button is pressed at these times,
there is the possibility that the lever
could accidentally enter the
&Por
&R
positions.
. When the vehicle is hot, the area
around the shift lever may be hot or
may produce an unusual sound,
however this does not indicate that
there is a malfunction.
NOTE:.When moving the shift lever out of the
&Pposition, it may not be possible to
move the shift lever if the button is
pressed before the brake pedal is
depressed. Press the button only after
depressing the brake pedal.
. Do not place coins or other small
objects in the area around the shift
lever. These objects may get stuck in
the shift gate and prevent the shift
lever from moving into a position.
Sometimes, you may not be able to retrieve these objects.
. Immediately after a cold start, while the
transmission system check display (“T/
M SYSTEM CHECK IN PROCESS”)
appears on the vehicle information
display, the shift lever cannot be moved
out of the
&Pposition. This is because a
check of the transmission system is in
progress. This does not indicate that
there is a malfunction. Move the shift
lever after the message on the vehicle
information display turns off.
. The shift lever knob and console-
mounted shift indicator have a genuine
leather finish that requires proper care
and maintenance. (
“CLEANING IN-
TERIOR” page 7-4)
Shift lock releaseIf the battery charge is low or discharged, the
shift lever may not be moved from the
&P
position even with the brake pedal depressed
and the shift lever button pushed.
To move the shift lever, perform the following
procedure.
1. Push the ignition switch to the OFF or LOCK position.
2. Apply the parking brake.
3. Remove the shift lock cover using a suitable tool wrapped with a cloth.
4. Push down the shift lock as illustrated.
5-16
Starting and driving
,QIRUPDWLRQ3URYLGHGE\

Black plate (189,1)
Model "R35-D" EDITED: 2008/ 5/ 20
GearMPH (km/h)
1st 35 (57)
2nd 62 (101)
3rd 90 (145)
4th —
5th —
6th —
DRIVING TIPSAfter starting the engine, fully depress the foot
brake pedal and push the shift lever button
before shifting the shift lever from the
&Pposition
to the
&R,&N,or
&A↔&M
position. Be sure the
vehicle is fully stopped before attempting to shift
the shift lever.
The transmission is designed so that the foot
brake pedal must be depressed before shifting
from
&Pto any other position.
The shift lever cannot be moved out of the
&P
position and into any other position with the
ignition switch other in the LOCK, OFF or ACC
position.When accelerating from a stopKeep the foot brake pedal depressed and push
the shift lever button to shift into a driving gear
as following:
. To drive forward, move the shift lever to the
&A↔&M
position.
. To back up, move the shift lever to the
&R
position.
Starting on level ground:1. Check the shift lever position indicator on
the instrument panel to confirm that the
driving gear is selected.
2. Release the parking brake.
3. Release the foot brake pedal, then gradually depress the accelerator pedal to start the
vehicle in motion.Starting on an uphill:1. Check the shift lever position indicator onthe instrument panel to confirm that the
driving gear is selected.NOTE:When starting or driving on a steep uphill
grade, shift to the
&M
position and operate
the paddle shifter to shift down to 1st gear
as a manual transmission vehicle.
2. With the parking brake applied, slowly release the foot brake pedal.
3. Slowly depress the accelerator pedal and feel the vehicle starting motion with the
parking brake applied.
4. Release the parking brake and gradually depress the accelerator pedal to start the
vehicle in motion.
NOTICE
To prevent stalling or transmission
damage, start in 1st gear. The
&M
position 2nd gear can be used to start
moving the vehicle only when reduced
torque is necessary on snowy roads or
extremely slippery surfaces.NOTE:The hill start assist function operates when
the vehicle is accelerating from a stop on
an uphill. (
“HILL START ASSIST” page
5-31)
When driving the vehicle
WARNING
Do not move the shift lever to the
&N
position while driving. Doing so may
result in an accident due to loss of
engine braking. It may also damage the
transmission.
Starting and driving
5-19
,QIRUPDWLRQ3URYLGHGE\

Black plate (190,1)
Model "R35-D" EDITED: 2008/ 5/ 20
Normal driving:Drive with the shift lever in the
&Aposition.
The appropriate gear will be automatically
shifted according to the position of the accel-
erator pedal, the driving speed and driving
conditions.
Passing or hill climbing:.
&Aposition:
Fully depress the accelerator pedal to the floor.
This shifts the transmission down into a lower
gear depending on the vehicle speed.
NOTE:When starting or driving on a steep uphill
grade, shift to the
&M
position and operate
the paddle shifter to shift down to 1st gear
as a manual transmission vehicle.
.
&M
position:
Use the paddle shifter to shift down, then
depress the accelerator pedal depending on
the vehicle speed.
Driving on a downhill:.
&Aposition:
The system shifts down according to the degree
of downhills to increase the effectiveness of the
engine brake. .
&M
position:
When driving on a long slope, selecting the
&M
position and 4th or 3rd gear will provide gentle
engine braking.
When driving on a steep downhill, selecting the&M
position and 2nd or 1st gear will provide
powerful engine braking.
WARNING
. When the shift lever is in the
&A
position, the adaptive shift control
system will stay in a low gear in
order to maintain the effectiveness
of the engine brake. However if the
vehicle is traveling too fast depend-
ing on the degree of the slope, you
should shift to the
&M
position and
use the paddle shifter to shift down.
If you continue to use only the foot
brake, a high load will be applied to
the brake, which may overheat,
reducing its effectiveness. Be sure
to use the engine brake together
with the foot brake. (
“Adaptive
shift control” page 5-17)
. The adaptive shift control system
may not operate when the transmis-
sion is not warm immediately after the start of driving, or when the oil
temperature is high. In this case,
depending on the degree of the
slope, you should shift to the
&M
position and select a lower gear.
. Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.
When stopping the vehicleLeave the shift lever in the
&A↔&Mor&Rposition
and firmly depress the foot brake pedal.
If the vehicle will be stopped for a long period of
time, apply the parking brake and move the shift
lever to the
&Por
&Nposition as necessary.WARNING
. Do not race the engine while the
vehicle is stopped. Doing so may
accelerate the vehicle suddenly and
cause an accident when shifting to a
driving gear.
. While the engine is running, the
propeller shaft that transmits torque
from the engine to the transmission
is turning at all times. Crawling or
reaching under the vehicle while the
engine is running may result in
5-20
Starting and driving
,QIRUPDWLRQ3URYLGHGE\

Black plate (191,1)
Model "R35-D" EDITED: 2008/ 5/ 20
serious injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.When parking the vehicle1. Bring the vehicle to a complete stop.
2. With the foot brake pedal depressed, applythe parking brake.
3. Move the shift lever to the
&Pposition.
4. Check the shift lever position indicator on the instrument panel to confirm that the
&P
position is selected.
5. Push the ignition switch to stop the engine.
WARNING
Before exiting the vehicle, be sure to
move the shift lever to the
&Pposition
and stop the engine. If the engine is
running and the shift lever is not in the
&Pposition, the vehicle may start mov-
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly caus-
ing an accident.
The control of the dual clutch transmission,
Bilstein DampTronic
®electronically controlled
shock absorbers and Vehicle Dynamic Control
(VDC) can be changed to the desired modes by
operating the setup switches. Select the desired
mode best suited to the driving conditions.
NOTE:Bilstein DampTronic
®is a registered trade-
mark of ThyssenKrupp Bilstein Suspen-
sion GmbH.
Starting and driving
5-21
VDC, TRANSMISSION AND
SUSPENSION SETUP SWITCHES
,QIRUPDWLRQ3URYLGHGE\