2009 MINI COOPER wheel bolts

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
119
Distributing liquid sealant
Immediately drive for approx. 10 minutes, so
that the liquid sealant is uniformly distributed.
Do not exceed speeds of 40 mph/
60 km/h.
If possible, do not drop below 10 mph/
20 km/h.<
Checking tire inflation pressure
1.After driving for approx. 10 minutes, pull
over at a suitable location.
2.Screw the hose with manometer back onto
the tire valve.
3.Check the tire inflation pressure.
The tire pressure must be at least
18 psi/130 kPa. If it is not, do not con-
tinue driving.<
If a tire pressure of at least 18 psi/130 kPa is dis-
played:
1.Switch on the compressor. Correct the tire
inflation pressure to the specified value,
page94.
2.Replace the tire as soon as possible.
Driving on
Do not exceed the permitted maximum
speed of 50 mph/80 km/h; doing so may
result in an accident.<
Replace the defective tire as soon as possible
and have the new wheel/tire assembly bal-
anced.
Have the MINI Mobility System refilled.
Tire change set
When changing a tire, always observe the safety
measures and the procedure for changing tires
described below.
In case of a flat tire the tire change set is
not needed due to the availability of the
MINI Mobility System.<
Changing wheels
Space-saver spare tire*
To change a space-saver spare tire, proceed as
follows:
>Remove space-saver spare tire, page120
>Prepare for tire change, page121
>Jack up vehicle, page121
>Mount space-saver spare tire, page121
>Tighten lug bolts, page121
>Drive with space-saver spare tire, page120
Tire change set for a space-saver spare
tire*
On vehicles with a space-saver spare tire, the
tire change set with onboard tools is stored
under the floor mat in the cargo bay.
1Chock, folding
2Hub cover remover
3Wheel stud wrench
4Vehicle jack
5Special wrench for removing the space-
saver spare tire
6Flat screwdriver/Phillips screwdriver
7Towing eyelet
8Lifting handle
The onboard tool kit includes a pouch with a
plastic bag in which you can place the damaged
wheel.
ProCarManuals.com

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
121
Preparing for a tire change
Observe the safety precautions regarding
flat tires on page117.<
Additional safety measures when chang-
ing tires:
Only change the tire when parked on a surface
that is level, firm and not slippery.
The vehicle or the jack could slip sideways on
soft or slippery support surfaces, such as snow,
ice, flagstones, etc.
Do not use a wooden block or similar object as a
support base for the jack, as this would prevent
it from extending to its full support height and
reduce its load-carrying capacity.
Do not lie under the vehicle or start the engine
when the vehicle is supported by the jack; other-
wise there is a risk of fatal injury.<
1.Place the foldable chock
* behind the front
wheel on the other side of the vehicle or in
front of the wheel if the vehicle is on an
incline. If the wheel is changed on a surface
with a more severe slope, take additional
precautions to secure the vehicle from roll-
ing.
2.Uncover the lug bolts if necessary.
If the wheel is equipped with a hub cover,
pry it off using the screwdriver from the tire
change kit.
3.Loosen the lug bolts by a half turn.
Jacking up the vehicle
The vehicle jack is designed for changing
wheels only. Do not attempt to raise
another vehicle model with it or to raise any load
of any kind. To do so could cause accidents and
personal injury.<1.Place the jack at the jacking point closest to
the wheel.
The jack base must be perpendicular to the
surface beneath the jacking point.
2.During jacking up, insert the jack head in the
square recess of the jacking point.
3.Jack the vehicle up until the wheel you are
changing is raised off the ground.
Mounting the space-saver spare tire
1.Unscrew the lug bolts and remove the
wheel.
2.Remove accumulations of mud or dirt from
the mounting surfaces of the wheel and
hub. Clean the lug bolts.
3.Lift the new wheel into place.
4.Screw at least two lug bolts finger-tight into
opposite bolt holes.
5.Screw in the remaining bolts.
6.Tighten all the lug bolts firmly in a diagonal
pattern.
7.Lower the vehicle.
8.Remove the jack.
Tightening the lug bolts
Tighten the lug bolts in a diagonal pattern.
Immediately have the wheels checked
with a calibrated torque wrench to ensure
that the lug bolts are firmly seated. Otherwise,
incorrectly tightened lug bolts can present a
safety hazard.<
Tightening torque: 103.3 lb ft or 140 Nm.
Replace the defective tire as soon as possible
and have the new wheel/tire assembly bal-
anced.
ProCarManuals.com

From A to Z
154
Telephone
– installation location, refer to
Center armrest79
– refer to separate Owner's
Manual
Telephone call, refer to the
Owner's Manual for the
telephone
Temperature display
– ice warning47
– outside temperature47
– setting the units50
Temperature of coolant, refer
to Coolant temperature47
Temperature setting
– air conditioner73
– automatic climate control75
Tensioning straps, refer to
Securing cargo88
The individual vehicle4
Third brake lamp, refer to
Center brake lamp117
Three-point safety belt32
Tightening the lug bolts
– keys119
– torque121
Tightening torque, refer to
Tightening the lug bolts121
Tire change set
– MINI Mobility System119
– space-saver spare tire119
Tire failure
– Flat Tire Monitor60
– indicator/warning lamp60
– MINI Mobility System117
– Run-Flat Tires60
– space-saver spare tire119
– Tire Pressure Monitor61
Tire inflation pressure94
– loss60
– space-saver spare tire94
Tire Pressure Monitor TPM61
– limitations of system61
– resetting system61
– warning lamp62
Tire pressure monitoring, refer
to Flat Tire Monitor59
Tire Quality Grading99Tires
– age100
– breaking in84
– changing, refer to Changing
wheels119
– condition100
– damage100
– inflation pressure94
– inflation pressure loss62
– minimum tread depth100
– new tires101
– pressure monitoring, refer to
Flat Tire Monitor59
– pressure monitoring, refer to
Tire Pressure Monitor
TPM61
– puncture60
– Run-Flat Tires101
– size99
– wear indicators, refer to
Minimum tread depth100
– winter tires102
Tires with safety features, refer
to Run-Flat Tires101
Tools, refer to Onboard tool
kit113
Torque142
– lug bolts121
Tow bar126
Tow fitting125
– screw thread125
Tow fittings for tow-starting
and towing away125
Tow rope126
Towing124
– car with automatic
transmission126
– methods126
Tow-starting124
TPM, refer to Tire Pressure
Monitor61
Track width, refer to
Dimensions143
Traction control, refer to
– Dynamic Stability Control
DSC57
Trailer operation
– Trailer loads and gross
vehicle weight144Transmission
– automatic transmission with
Steptronic39
– manual transmission39
– overriding selector lever lock
for automatic transmission
with Steptronic41
Transport securing devices,
refer to Securing cargo88
Transporting children safely35
Tread depth, refer to Minimum
tire tread100
Trip odometer47
Trip-distance counter, refer to
Trip odometer47
Triple turn signal activation42
Turn signal indicator41
– front, replacing bulb115
– indicator lamp12
– rear, replacing bulb116
– side, replacing bulb116
Turning circle, refer to
Dimensions143
Tying down loads, refer to
Cargo loading88
U
Uniform Tire Quality Grading
UTQR99
Units
– average fuel consumption50
– temperature50
Universal garage door opener,
refer to Integrated universal
remote control77
Universal remove control77
Unlatching, refer to
Unlocking26
Unlocking
– from inside22
– from outside19
– tailgate26
– without remote control, refer
to Convenient access25
Upholstery, care110
USB-audio interface80
ProCarManuals.com