2009 MAZDA MODEL 6 Maintenance

Black plate (388,1)
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse orderof removal.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls don't
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.
qFuse Replacement
Replacing the fuses on the driver's sidekick-panel
If the electrical system does not work,
first inspect the fuses on the driver's side
kick-panel.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover by sliding the cover straight back toward you.
CAUTION
Pulling the cover off sideways may
break the retaining tabs off.
8-46
Maintenance and Care
Owner Maintenance
Mazda6_8Z64-EA-08H_Edition1 Page388
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (389,1)
3. Pull the fuse straight out with the fusepuller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
Maintenance and Care
Owner Maintenance
8-47
Mazda6_8Z64-EA-08H_Edition1 Page389
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (390,1)
4. Install the right side of the fuse blockcover first as shown the figure.
WARNING
Do not replace the main fuse by
yourself. Have an Authorized Mazda
Dealer perform the replacement: Replacing the fuse by yourself is
dangerous because the MAIN fuse is
a high current fuse. Incorrect
replacement could cause an electrical
shock or a short circuit resulting in a
fire.
8-48
Maintenance and Care
Owner Maintenance
Mazda6_8Z64-EA-08H_Edition1 Page390
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (391,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
1 M.DEF 10 A Mirror defroster
í
2ST SIG 5 A Starter sig
3 ABS SOL 30 A ABS, DSCí
4 P.WIND (P) 25 A Power window
5 P.SEAT (P) 30 A Power seatí
6 SUN ROOF 15 A Moonroofí
7 TAIL 15 A BCM, Tail lamp
8 P.OUTLET (R) 15 A Accessory sockets
9 AUDIO 30 A Audio system (Bose
®Sound System-equipped model)
10 ABS MOTOR 60 A ABS, DSCí
11 P.WIND (D) 40 A Power window
12 DEFOG 40 A Rear window defroster
13 SEAT HEAT 20 A Seat heat
14 A/C 10 A Air conditioner
15 FOG 15 A Fog lights
í
16 BLOWER 2 15 A Blower motor
17FAN 60 A Cooling fan
Maintenance and Care
Owner Maintenance
8-49íSome models.
Mazda6_8Z64-EA-08H_Edition1 Page391
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (392,1)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
18 P.SEAT (D) 30 A Power seat
í
19 BTN 30 A For protection of various circuits
20 IG KEY2 40 A Starting system
21 BLOWER 40 A Blower motor
22 FUEL PUMP 25 A Fuel pump
23 ENGINE2 15 A Engine control system
24 EGI INJ 15 A Injector
25 PCM 10 A Engine control system
26 ENGINE 10 A
*1Engine control system
20 A*2
27 IG 20 A For protection of various circuits
28 TCM 20 A TCMí
29ESCL 10 A Electronic steering lock
30 IG KEY1 40 A For protection of various circuits
31 MAIN 125 A For protection of all circuits
32 DRL 20 A DRL
í
33 HAZARD 10 A Hazard warning flashers
34 ENG+B 10 A PCM
35 STOP 10 A Brake lights
36 HORN 15 A Horn
37 HEAD HI RH 15 A Headlight-high beam (Right)
38 HEAD LO RH 10 A Headlight-low beam (Right)
39 HEAD HI LH 15 A Headlight-high beam (Left)
40 HEAD LO LH 10 A Headlight-low beam (Left)
*1 2.5-liter engine
*2 3.7-liter engine
8-50
Maintenance and Care
íSome models.
Owner Maintenance
Mazda6_8Z64-EA-08H_Edition1 Page392
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (393,1)
Fuse block (Passenger's side)
DESCRIPTIONFUSE
RATING PROTECTED COMPONENT
1 P.WIND 30 A Power window
2 METER IG 15 A For protection of various circuits
3 ILLUMI 7.5 A BCM, Illumination
4 MIRROR 5 A Power control mirror
5 SAS 5 A Air bag, ABS
6 ―― ―
7 INT, LOCK/SHIFT 5 A AT shift
í
8 ―― ―
9 HEGO 5 A Power control mirror
10 A/C 10 A Air conditioner
11 P.OUTLET/CIGAR 15 A Lighter
í
12 D.LOOK 25 A BCM, Door lock motor
13 ENGINE IG 15 A Engine control system
14 WIPER 25 A Windshield wiper and washer
15 ROOM 15 A Interior lights
16 SPARE ――
17 SPARE ――
18 SPARE ――
Maintenance and Care
Owner Maintenance
8-51íSome models.
Mazda6_8Z64-EA-08H_Edition1 Page393
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (394,1)
How to Minimize
Environmental Paint Damage
The paintwork on your Mazda represents
the latest technical developments in
composition and methods of application.
Environmental hazards, however, can
harm the paint's protective properties, if
proper care is not taken.
Here are some examples of possible
damage, with tips on how to prevent
them.
qEtching Caused by Acid Rain or
Industrial Fallout
Occurrence
Industrial pollutants and vehicle emissions
drift into the air and mix with rain or dew
to form acids. These acids can settle on a
vehicle's finish. As the water evaporates,
the acid becomes concentrated and can
damage the finish.
And the longer the acid remains on the
surface, the greater the chance is for
damage.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you suspect that acid rain has settled on
your vehicle's finish.
qDamage Caused by Bird
Dropping, Insects, or Tree Sap
Occurrence
Bird droppings contain acids. If these
aren't removed they can eat away the clear
and color base coat of the vehicle's
paintwork.
When insects stick to the paint surface
and decompose, corrosive compounds
form. These can erode the clear and color
base coat of the vehicle's paintwork if
they are not removed.
Tree sap will harden and adhere
permanently to the paint finish. If you
scratch the sap off while it is hard, some
vehicle paint could come off with it.
Prevention
It is necessary to have your Mazda
washed and waxed to preserve its finish
according to the instructions in this
section. This should be done as soon as
possible.
Bird droppings can be removed with a
soft sponge and water. If you are traveling
and these are not available, a moistened
tissue may also take care of the problem.
The cleaned area should be waxed
according to the instructions in this
section.
Insects and tree sap are best removed with
a soft sponge and water or a commercially
available chemical cleaner.
Another method is to cover the affected
area with dampened newspaper for one to
two hours. After removing the newspaper,
rinse off the loosened debris with water.
8-52
Maintenance and Care
Appearance Care
Mazda6_8Z64-EA-08H_Edition1 Page394
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H

Black plate (395,1)
qWater Marks
Occurrence
Rain, fog, dew, and even tap water can
contain harmful minerals such as salt and
lime. If moisture containing these
minerals settles on the vehicle and
evaporates, the minerals will concentrate
and harden to form white rings. The rings
can damage your vehicle's finish.
Prevention
It is necessary to wash and wax your
vehicle to preserve its finish according to
the instructions in this section. These
steps should be taken immediately after
you find water marks on your vehicle's
finish.
qPaint Chipping
Occurrence
Paint chipping occurs when gravel thrown
in the air by another vehicle's tires hits
your vehicle.
How to avoid paint chipping
Keeping a safe distance between you and
the vehicle ahead reduces the chances of
having your paint chipped by flying
gravel. NOTE
lThe paint chipping zone varies with the
speed of the vehicle. For example, when
traveling at 90 km/h (56 mph), the paint
chipping zone is 50 m (164 ft).
lIn low temperatures a vehicle's finish
hardens. This increases the chance of paint
chipping.
lChipped paint can lead to rust forming on
your Mazda. Before this happens, repair the
damage by using Mazda touch-up paint
according to the instructions in this section.
Failure to repair the affected area could
lead to serious rusting and expensive
repairs.
Maintenance and Care
Appearance Care
8-53
Mazda6_8Z64-EA-08H_Edition1 Page395
Wednesday, June 25 2008 10:5 AM
Form No.8Z64-EA-08H