2009 Lancia Musa rims

145
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 11L0D0397m
fig. 12L0D0163m
❒for cars with alloy rims, remove
the hub cap using the screwdriver
provided, by levering at the ap-
propriate groove E- fig. 11, as
shown in the figure;
❒loosen the bolts of the wheel to be
replaced by about one turn with
the wrench provided E-fig. 12; if
the car is fitted with alloy rims,
shake the car to facilitate remov-
ing the rim from the wheel hub;❒activate the device F- fig. 13so as
to extend the jack, until the groove
Gon the upper part of the jack fits
correctly into the lower profile H
visible on the car body next to the
indicationI(at approx. 60 cm
from the centre of the front wheel
or 80 cm from the centre of the
rear wheel);
❒advise any personnel present in
the area that the car is about to be
lifted; it is therefore vital not to
stand near it or to touch it until it
has been lowered again;❒fit the handle L- fig. 13to as to
be able to operate the jack and
continue to raise the care until it is
a few centimetres off the ground;
❒for versions with wheel cap, re-
move the wheel cap after loosen-
ing the 3 fastening bolts and fi-
nally loosen the fourth bolt and
extract the wheel;
❒for versions with snap-fitted wheel
cap, remove the cap, taking care
not to damage it;
❒ensure that the surfaces of the
small spare wheel in contact with
the hub are clean and free from
impurities that could, subse-
quently, lead to the loosening of
the fastening bolts;
L0D0164mfig. 13
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 145

146
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 14L0D0165mfig. 15L0D0166m
❒fit the spare wheel, ensuring that
the holes coincide M-fig. 14with
their respective centring pins N;
❒using the wrench provided, tighten
the four fastening bolts;
❒turn the jack handle to lower the
car and remove the jack;
❒using the wrench provided, screw
the bolts right down in a criss-
cross fashion, in the sequence
shown in the figureREFITTING THE
STANDARD WHEEL
Following the procedure described
previously, raise the car and remove
the small spare wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces be-
tween spare wheel and hub are
clean and free from impurities so
that the fastening bolts will not
come loose;
❒fit the standard wheel by inserting
the first two-threaded bolt in the
hole nearest to the inflation valve;❒fit the wheel cap, ensuring that the
groove (in the cap itself) coincides
with the inflation valve. Then fit
the other three bolts;
❒for versions with snap-fitted wheel
cap, press down on the edge of the
cap, with the palm of your hand
(do not strike it) against the wheel;
❒Using the wrench provided, se-
curely tighten the fastening bolts;
❒lower the car and remove the jack;
❒Using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15;
IMPORTANT If it is not fitted prop-
erly, the wheel cap may detach itself
when the vehicle is running.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 146

147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Ensure that the surfaces in contact
with the hub are clean;
❒install the standard wheel by fit-
ting it on the centring pins. Fit the
fastening bolts and screw them
down using the wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15for the small
spare wheel;
❒refit the snap-fitted hub cap.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒ fit the jack partially open in its
box, forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒stow the container, complete with
tools, into the spare wheel, screw-
ing in the locking device;
❒put the boot’s stiff preformed in-
sulating mat back in position.WHEN NEEDING
TO CHANGE
A BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location;
❒Before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒For safety reasons, always check
the height of the headlight beam
after changing a bulb.
Halogen lamps must be han-
dled holding the metallic
part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self. In the event of accidental contact,
rub the bulb with a cloth dampened
with alcohol and allow to dry.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 147

180
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
❒the tyre ages even if rarely used.
Cracks in the tread and on the
sidewalls are a sign of ageing.
Have the tyres checked by spe-
cialised personnel if they have
been fitted for longer than 6 years.
Remember to check the spare
wheel very carefully;
❒In the case of replacement, always
fit new tyres, avoiding those of du-
bious origin;
❒If a tyre is changed, also change
the inflation valve;
❒to allow even wear between the
front and rear tyres, it is advisable
to change them over every 10-15
thousand kilometres, keeping
them on the same side of the car
so as not to reverse the direction of
rotation.
Remember that road hold-
ing depends also on the cor-
rect tyre inflation pressure.
WARNING
If the pressure is too low the
tyre overheats and this can
cause it serious damage.
WARNING
Do not cross switch the tyres,
moving them from the right
of the car to the left and vice versa.
WARNING
Never subject alloy rims to
repainting treatments re-
quiring the use of temperatures ex-
ceeding 150°C. The mechanical
properties of the wheels could be im-
paired.
WARNING
RUBBER HOSES
As far as the brake system and fuel
rubber hoses are concerned, carefully
follow the “Service schedule” in this
section.
Ozone, high temperatures and pro-
longed lack of fluid in the system may
cause hardening and cracking of the
hoses, with possible leaks. Careful in-
spections are therefore necessary.
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 180

194
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
WHEELS
RIMS AND TYRES fig. 5
Pressed steel or alloy rims. Tubeless
radial carcass tyres. All approved
tyres are listed in the Log Book.
IMPORTANT In the event of discrep-
ancies between the information pro-
vided on this “Owner handbook” and
the “Log book”, consider the specifi-
cations shown in the log book only.
Respect the prescribed size to ensure
safety of the car in movement. Fit
tyres of the same make and type on
all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.READING TYRE MARKINGS
Example: 185/65 R 14 86 T
185= Nominal width (S, distance in
mm between sidewalls).
65= Height/width ratio (H/S) in
percentage.
R= Radial tyre.
14= Rim diameter in inches (Ø).
86Load rate (capacity).
T= Maximum speed rating.
fig. 5L0D0229m
SMALL SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Toe-in measured between rims: 0 ±1
mm.
The values refer to the car in running
order.
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 194

196
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
185/65 R14 86T
195/60 R15 88H
205/50 R16 87V (**)
195/60 R15 88H
205/50 R16 87V (**)185/65 R14 86Q (M+S)
195/60 R15 88Q (M+S)
–
195/60 R15 88Q (M+S)
–4Bx14” (***) 135/80 B14 84M (***)
1.3 Multijet
90HP
e 1.6 Multijet
4Bx15” 125/80 R15 95M (***)
4Bx15” 125/80 R15 95M
RIMS AND TYRES
(*) Alloy rim on request
(**) Not snow chains
(***)IMPORTANT The 14” small wheel can only be used on 1.4 petrol and 1.3 Multijet 70CV cars with chassis number over
1012200.
VERSIONSRIMSTYRES SMALL SPARE WHEELSupplied Winter type Rim Tyre
alternatively1.4 petrol
and 1.3 Multijet
70HP
6 Jx14” ET 40
6 Jx15” ET 40 (*)
6 1/2 Jx16” ET 40 (alloy)
6Jx15” ET 40 (*)
6 1/2 Jx16” ET 40 (alloy)
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 196

Plates ..................................... 188
Pretensioners ........................ 99
Protecting the environment ... 94
Rain sensor ........................... 65
Rear fog lights
– bulb replacement
procedure .............................. 154
– control button .................. 71
Rear screen washer
– control ............................ 64
– fluid level ......................... 175
Rear screen wiper
– blade ................................ 181
– control ............................ 64
– sprayers ........................... 182
Rearview mirrors .................. 46
Rev counter ........................... 21
Reversing light
– bulb replacement
procedure .............................. 154
Rims and wheels ................... 194
Roof bars ............................. 83
Rubber hoses ........................ 180Safety ................................... 95
Seat belts
– general information .......... 100
– height adjustment ............ 97
– maintenance ..................... 101
– S.B.R. system .................. 97
– use ................................... 96
Seats ..................................... 38
Side airbags ........................... 110
Sidelights
– bulb replacement
procedure .............................. 152
– control ............................ 63
Snow chains .......................... 123
Spark plugs............................ 191
Speedometer .......................... 21
Starting and driving .............. 113
Starting the engine
– bump starting ................... 137
– how to warm up the engine
after it has just started .......... 115
– ignition switch .................. 20
– jump starting ................... 138– procedure for Multijet
versions ................................. 114
– procedure for petrol
versions ................................. 114
– stopping the engine ........... 115
Steering ................................ 193
Steering wheel adjustment .... 45
Steering wheel lock ............... 20
Sun visors ............................. 76
Sunroof .................................. 76
Suspensions .......................... 193
Symbols ................................ 11
Technical data ...................... 187
Third brake light
– bulb replacement
procedure .............................. 154
Towing the car ...................... 163
Towing trailers ...................... 119
Transmission ......................... 192
Two-zone automatic climate control
system ................................... 52
Upper oddment compartments 73
208
STARTING
AND
DRIVING
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
206-216 MUSA 1ed GB 10-07-2008 11:08 Pagina 208