2009 Lancia Musa fuse

68
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DEVICE DISENGAGEMENT
Turn the knurled ring A-fig. 75to
OFFor the ignition key to STOP. In
addition, the device is automatically
disengaged in one of the following
cases:
❒pressing the brake pedal. TO REDUCE MEMORISED SPEED
The stored speed can be increased in
two ways:
❒disengaging the device and then
memorising the new speed;
or
❒moving the stalk downwards (
–)
until reaching the new speed which
will be memorised automatically.
Each operation of the stalk will cor-
respond to a slight reduction in speed
(about 1 km/h), while keeping the
stalk downwards will correspond to a
continuous speed reduction. RESTORING STORED SPEED
If the device has been disengaged for
example pressing the brake or clutch
pedal, the memorised speed can be re-
set as follows:
❒accelerate gradually until reaching
a speed approaching the one
memorised;
❒engage the gear selected at the
time of speed memorising (4
thor
5thgear);
❒press the button RES B.
TO INCREASE THE MEMORISED
SPEED
The stored speed can be increased
in two ways:
❒pressing the accelerator and then
memorising the new speed
reached;
or
❒moving the stalk upwards (
+).
Each operation of the stalk will cor-
respond to a slight increase in speed
(about 1 km/h), while keeping the
stalk upwards will correspond to a
continuous speed increase.
While travelling with the
device engaged, do not set
the gearshift lever to neutral.
WARNING
In case of malfunctioning or
fault of the device, turn the
knurled ring to OFF and contact the
Lancia Dealership, after checking
that the protection fuse is not blown.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 68

90
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT When making ma-
noeuvres requiring maximum steering
efforts, the steering wheel may be-
come hard to turn; this is normal and
is due to the intervention of the steer-
ing control electric motor overheating
protection system. No repairs are,
therefore, required. The power steer-
ing system will return to normal op-
eration the next time the car is used.PARKING SENSORS
(where provided)
Parking sensors are located in the rear
bumper and their function is to in-
form the driver, through an intermit-
tent buzzer, of the presence of obsta-
cles behind the car.
ACTIVATION
The sensors are automatically acti-
vated when the reverse gear is en-
gaged. As the distance from the ob-
stacle behind the car decreases, the
acoustic alarm becomes more fre-
quent.
fig. 119L0D0419m
Under no circumstances
should after-market opera-
tions involving steering system or
steering column modifications (e.g.:
installation of anti-theft device) be
carried out, because they could
badly affect performance and safety,
cause the lapse of the warranty and
also result in car non-compliance
with homologation requirements.
WARNING
FAILURE INDICATIONS
Any failure of the power steering is in-
dicated by instrument panel warning
light
gcoming on together with the
message on the multifunction display
(see section “Warning lights and mes-
sages”). In the event of a failure of the
electric power steering, the car con-
tinues in any case to be manoeuvrable
with mechanical steering so that it can
be taken soon as possible to a Lancia
Dealership.
Before servicing the car,
switch off the engine and
remove the key from the ignition de-
vice, activating the steering lock, es-
pecially when car wheels do not
touch the ground. If this is not pos-
sible (if the key must be on MAR or
the engine must be running), re-
move the main fuse which protects
the electric power steering.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:11 Pagina 90

132
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
GENERAL FAILURE
INDICATION
(amber)
The warning light turns on in
the following circumstances.
Externallight failure
The warning light comes on (on some
versions only) when a failure is de-
tected in one of the following lights:
– tail lights
– stop lights (excluding 3
rdstop)
– rear fog lights
– direction indicators
– plate lights.
The fault identified in the lights above
may be due to: one or more burnt
lamps, a blown protection fuse or in-
terruption of the electrical connection.
The display will show the dedicated
message.
è
Fresh air filter clogged
(where provided)
The warning light turns on when the
particulate filter is clogged and the
driving conditions do not enable au-
tomatic activation of the regeneration
procedure.
To allow the regeneration procedure,
keep the car running until the warn-
ing light turns off.
The display will show the dedicated
message.
Engine oil pressure sensor failure
The warning light turns on when a
failure is detected in the engine oil
pressure sensor. Go to a Lancia Deal-
ership as soon as possible.Twilight/rain sensor failure
The warning light turns on when a
failure is detected in the twilight/rain
sensors. Go to a Lancia Dealership as
soon as possible.
The display will show the dedicated
message.
Fuel cut-off switch tripped
The warning light comes on when the
fuel cut-off switch trips.
The display will show the dedicated
message.
Speed limit exceeded
The display shows the dedicated mes-
sage when the car exceeds the set
speed limit (see “Multifunction Dis-
play” in section “Dashboard and con-
trols”).
125-134 MUSA 1ed GB 10-07-2008 9:38 Pagina 132

135
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
IN AN EMERGENCY
OPENING/CLOSING OF DOORS...................... 136
ENGINE STARTING .......................................... 136
QUICK TYRE REPAIR KIT
FIX & GO automatic......................................... 138
REPLACING A WHEEL.................................... 142
WHEN NEEDING TO CHANGE A BULB ......... 147
IF AN EXTERIOR LIGHT BURNS OUT ............ 150
IF AN INTERIOR LIGHT BURNS OUT............. 155
IF A FUSE BLOWS............................................ 156
IF THE BATTERY IS FLAT .............................. 162
LIFTING THE CAR........................................... 162
TOWING THE CAR........................................... 163
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 135

147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Ensure that the surfaces in contact
with the hub are clean;
❒install the standard wheel by fit-
ting it on the centring pins. Fit the
fastening bolts and screw them
down using the wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15for the small
spare wheel;
❒refit the snap-fitted hub cap.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒ fit the jack partially open in its
box, forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒stow the container, complete with
tools, into the spare wheel, screw-
ing in the locking device;
❒put the boot’s stiff preformed in-
sulating mat back in position.WHEN NEEDING
TO CHANGE
A BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location;
❒Before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒For safety reasons, always check
the height of the headlight beam
after changing a bulb.
Halogen lamps must be han-
dled holding the metallic
part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self. In the event of accidental contact,
rub the bulb with a cloth dampened
with alcohol and allow to dry.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 147

150
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
IF AN EXTERIOR
LIGHT BURNS OUT
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT CLUSTERS
The front light clusters contain side-
lights, dipped beam, main beam and
direction indicator bulbs.
To replace the bulbs in the sidelights,
dipped beam and main beam lights,
remove the protective caps.The bulbs are arranged inside the
light unit fig. 17:as follows:
Cdirection indicators
Dmain beam
Bsidelights
Fdipped beam
After replacing the bulbs, put the
protective caps for the lights changed
back into position and ensure that
they are effectively locked into place.IMPORTANT To access the bulb
holder of the left headlight (direction
of travel) in order to replace it, first
remove the protective cover B-fig. 18
of the fuse box in the engine com-
partment.
fig. 17L0D0398mfig. 18L0D0125m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 150

156
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
BOOT LIGHT fig. 34
To change the bulb, proceed as fol-
lows:
❒open the tailgate;
❒remove the light Alevering in the
point shown by the arrow.
❒open the protection Band replace
the snap-fitted bulb;
❒re-close the protective cover Bon
the lens;
❒refit the light Ainserting it in its
correct position firstly on one end
and then on the other until it
clicks into place.
fig. 34L0D0197m
IF A FUSE BLOWS
GENERALITIES fig. 35
The fuse is a protective device for the
electric system: it comes into action
(i.e. it cuts off) mainly due to a fault
or improper action on the system.
Check the efficiency of the corre-
sponding fuse when a device does not
work: the conducting element Amust
not be interrupted. If it is, replace the
blown fuse with another with the
same amperage (same colour).
B: intact fuse.
C: fuse with damaged filament.
To replace a fuse use the pliers Dat-
tached to the fuse box on the instru-
ment dashboard.
fig. 35L0D0198m
If the fuse should fail again,
contact a Lancia Dealer-
ship.
WARNING
Never change a fuse with an-
other with a higher amp rat-
ing; DANGER OF FIRE.
If a general fuse (MEGA-
FUSE,MIDI-FUSE, MAXI-
FUSE) cuts in, contact a Lancia Deal-
ership.
WARNING
Before changing a fuse,
check that the ignition key
has been removed and that all the
other electric devices have been
turned off/disabled.
WARNING
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 156

157
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
FUSE LOCATION
The fuses in the car are grouped in
two fuse boxes located on the instru-
ment dashboard on the left-hand side
of the steering column and in the en-
gine compartment next to the battery.
Fuse box on the instrument
dashboard fig. 37
To access the fuse box on the instru-
ment dashboard, unscrew the retain-
ing device A-fig. 36, and remove the
protective panel B.
L0D0200m
fig. 36L0D0424m
fig. 37
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 157