2009 Lancia Musa lock

86
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
EOBD SYSTEM
The EOBD system (European On
Board Diagnosis) allows continuous
diagnosis of the components of the car
correlated with emissions.
It also alerts the driver, by turning on
the warning light
Uon the instru-
ment panel (together with relevant
message on the multifunction display,
where provided) (see section “Warn-
ing lights and messages”), when these
components are no longer in peak
conditions.
The objective is:
❒to keep the system efficiency un-
der control;
❒to warn when a fault causes emis-
sion levels to increase;
❒to signal the need to replace worn
components. EBD failure
EBD failure is indicated by the turn-
ing on warning lights >andxon
the instrument panel, together with
the message (where provided) shown
on the multifunctional display (see
section “Warning lights and mes-
sages”).
In this case, the rear wheels may sud-
denly lock and the car may swerve.
Drive carefully to the nearest Lancia
Dealership to have the system
checked.
When the ABS intervenes,
a slight pulsing of the brake
pedal is felt. Do not lessen the pres-
sure of your foot on the pedal; main-
tain pressure on the brake without
hesitation; this will ensure that you
stop in the shortest possible space al-
lowed by the road conditions.
WARNING
If the warning lightxon
the instrument panel goes
on (and a message, were provided,
is shown in the multifunctional dis-
play), stop the car immediately and
contact your nearest Lancia Dealer-
ship. Leakage of hydraulic fluid
from the braking system will com-
promise functionality of the braking
system, either of the conventional
type or with ABS.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 86

90
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IMPORTANT When making ma-
noeuvres requiring maximum steering
efforts, the steering wheel may be-
come hard to turn; this is normal and
is due to the intervention of the steer-
ing control electric motor overheating
protection system. No repairs are,
therefore, required. The power steer-
ing system will return to normal op-
eration the next time the car is used.PARKING SENSORS
(where provided)
Parking sensors are located in the rear
bumper and their function is to in-
form the driver, through an intermit-
tent buzzer, of the presence of obsta-
cles behind the car.
ACTIVATION
The sensors are automatically acti-
vated when the reverse gear is en-
gaged. As the distance from the ob-
stacle behind the car decreases, the
acoustic alarm becomes more fre-
quent.
fig. 119L0D0419m
Under no circumstances
should after-market opera-
tions involving steering system or
steering column modifications (e.g.:
installation of anti-theft device) be
carried out, because they could
badly affect performance and safety,
cause the lapse of the warranty and
also result in car non-compliance
with homologation requirements.
WARNING
FAILURE INDICATIONS
Any failure of the power steering is in-
dicated by instrument panel warning
light
gcoming on together with the
message on the multifunction display
(see section “Warning lights and mes-
sages”). In the event of a failure of the
electric power steering, the car con-
tinues in any case to be manoeuvrable
with mechanical steering so that it can
be taken soon as possible to a Lancia
Dealership.
Before servicing the car,
switch off the engine and
remove the key from the ignition de-
vice, activating the steering lock, es-
pecially when car wheels do not
touch the ground. If this is not pos-
sible (if the key must be on MAR or
the engine must be running), re-
move the main fuse which protects
the electric power steering.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:11 Pagina 90

93
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
FUEL FILLER CAP
The opening of the fuel flap is inter-
locked with the door opening/closing
control. For this reason, if the doors
are locked, in order to refuel, press
buttonD-fig. 122.
The cap C-fig, 121is provided with a
loss prevention device Bwhich secures
it to the lid Aso that it cannot be lost.
To open the cap C, turn it anticlock-
wise and remove it. FILLING THE TANK
To fill the tank completely, top-up
twice after the pump switches off.
Further top-ups could cause faults in
the fuel feeding system.
For diesel engines, use diesel
fuel for motor vehicles com-
pliant with EN590 Euro-
pean specifications only. The
use of other products or mixtures may
damage the engine beyond repair and
consequently cause lapse of warranty
in relation to the damage caused. If
you accidentally introduce other types
of fuel in the tank, do not start the en-
gine and empty the tank. If the engine
has run also for a very short time, you
will need to have the entire fuel feed
system emptied in addition to the
tank.
fig. 121L0D0399m
fig. 122L0D0420m
EMERGENCY OPENING
OF THE FLAP
In an emergency it is possible to open
the flap by pulling the cord A-fig. 123.
To reach the cord, remove the protec-
tive cover.
fig. 123L0D0490m
038-094 MUSA 1ed GB 11-07-2008 14:11 Pagina 93

94
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
peratures, etc.) and it will then calcu-
late the amount of particulates trapped
by the filter. Since this filter physically
traps particulates, it shall be cleaned
(reclaimed) at regular intervals by
burning carbon particles. The regener-
ation procedure is controlled automat-
ically by the engine control unit ac-
cording to the filter conditions and the
conditions of use of the car. During the
regeneration procedure, the following
situations may occur: limited increase
of idle speed, activation of electric fan,
limited increase of smoke, high tem-
peratures at the exhaust. These are not
anomalies; they do not impair car be-
haviour and the environment. If the
dedicated message is displayed, refer to
section “Warning lights and messages”.PROTECTING THE
ENVIRONMENT
The devices for curtailing petrol engine
emissions are the following:
❒three-way catalytic converter;
❒Lambda sensors;
❒fuel evaporation prevention system.
In addition, do not let the engine run,
even for a test, with one or more spark
plugs disconnected.
The devices for curtailing diesel fuel en-
gine emissions are the following:
❒oxidising catalytic converter;
❒exhaust gas recirculation system
(E.G.R.);
❒diesel particulate filter (DPF)
DIESEL PARTICULATE
FILTER (DPF)
(for 1.3 Multijet 90 CV versions)
The Diesel Particulate Filter is a me-
chanical filter, integral with the exhaust
system, that physically traps particu-
lates present in the exhaust gases of
Diesel engines. The diesel particulate
filter has been adopted to eliminate al-
most totally particulates in compliance
with current / future law regulations.
During normal use of the car, the en-
gine control unit records a set of data
(e.g.: travel time, type of route, tem- During refuelling, attach the cap to
the device on the inside of the flap, as
shown in the figure.
IMPORTANT The sealing of the tank
may cause light pressuring in the
tank. A little breathing off, while
slackening the cap, is absolutely nor-
mal.
After refuelling, tighten the cap by
turning it clockwise until you hear one
or more clicks. Then turn the key
clockwise and remove it and close the
flap.
Do not place naked flames
or lit cigarettes near to the
fuel filler: fire risk. Keep your face
away from the fuel filler to prevent
breathing in harmful vapours.
WARNING
The catalytic converter de-
velops high temperature
during operation. Do not park on
grass, dry leaves, pine needles or
other flammable material: fire risk.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:11 Pagina 94

96
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
SEAT BELTS
USE OF SIDE REAR
AND FRONT SEAT BEALTS
Wear the belt keeping the chest
straight and rested against the back-
rest.
To fasten the seat belts, hold the
tongueA-fig. 1and insert it into the
buckleB, until the locking click is
heard.
If the belt jams when it is extracted,
let it rewind for a short stretch, then
pull it out again without jerking.
Press button Cto release the belt. Ac-
company the belt while it is being re-
wound to prevent twisting.
Through the reel, the belt automati-
cally adapts to the body of the pas-
senger wearing it, thus giving him/her
freedom of movement.The reel may get blocked when the
car is parked on a steep slope: this is
perfectly normal. In addition, the reel
mechanism blocks the belt whenever
it is pulled and in the event of brisk
braking, collisions and on high speed
bends.
The rear seat is supplied with inertial
reel-driven seat belts with three hook-
ing points. Rear seat belts must be worn as
shown in diagram D-fig. 2(5 seat ver-
sions) or diagram E-fig. 3(4 seat ver-
sions).
fig. 1L0D0126m
fig. 2L0D0430m
fig. 3L0D0431m
Never press button C-fig. 1
when travelling.
WARNING
095-112 MUSA 1ed GB 10-07-2008 9:37 Pagina 96

97
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
S.B.R. system
The car is fitted with a Seat Belt Re-
minder system (S.B.R.), consisting of
a buzzer and a flashing warning light
warns the driver that the seat belt
must be fastened.
The buzzer can be deactivated tem-
porarily (until the next engine stop)
as follows:
❒fasten the driver’s seat belt;
❒turn the ignition key to MAR
❒wait for over 20 seconds and then
release at least one of the seat
belts.
For permanent deactivation, contact
Lancia Dealership.
The S.B.R. system can be re-activated
through the “Setup” menu only (see
paragraph “Seat belts not fastened”
in section “Warning lights and mes-
sages”).ADJUSTING THE
FRONT SEAT BELT HEIGHT
(where provided)
Always adjust the seat belt height to
the passenger’s body. This precaution
may considerably reduce the risk of
injury in the event of a collision.
Correct regulation is obtained when
the belt passes approximately half
way between the shoulder and the
neck.
To adjust, either lift or lower the grip
A-fig. 4of the locking mechanism and
at the same time move the ring Bto
the most suitable of the allowed posi-
tions.
Remember that in the event
of a violent collision, rear
seat passengers that do not wear seat
belts both pose a risk for their safety
and also represent a serious danger
for the front seat passengers.
WARNING
fig. 4L0D0128m
Stop the car to adjust the
seat belt height.
WARNING
After the adjustment, make
sure that the cursor to
which the ring is secured is blocked
in one of the possible positions. Re-
lease the grip and push downwards
to enable the locking device to click
if the grip has not been released in
one of the possible positions.
WARNING
095-112 MUSA 1ed GB 10-07-2008 9:37 Pagina 97

99
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
PRETENSIONERS
To increase the protection efficiency
of the seat belts, the car is fitted with
front pretension. In the event of a vi-
olent crash, these devices rewind the
seat belts a few centimetres. In this
way they ensure that the seat belt per-
fectly adheres to the wearer before the
restraining action begins.
When the pretensioner is engaged, the
reel is blocked. The belt is no longer
wound even if it is accompanied.The pretensioner can only
be used once. Go to a Lan-
cia Dealership to have it replaced af-
ter is has been deployed. For device
validity refer to the plate positioned
inside the upper glove box on the
passenger’s side. Refer to the Lancia
Dealership when the time comes to
replace the device.
WARNING
Operations which lead to
shocks, vibrations or lo-
calised heating (over 100°C
for a maximum of 6 hours)
in the area around the pretensioners
may damage or trigger them. These
devices are not affected by vibrations
caused by irregularities of the road
surface or low obstacles such as kerbs,
etc. Contact Lancia Dealership for
any assistance.
IMPORTANT Maximum protection is
obtained from the pretensioner if the
belt is worn tight on the chest and
hips.
A slight emission of smoke may occur.
This smoke is not harmful and does
not indicate a fire.
The pretensioner does not require any
maintenance or greasing.
Any work tampering with its original
conditions invalidates pretensioner ef-
ficiency.
If unusual natural events (floods, sea
storms, etc.) have caused the device
to be contaminated by water and
mud, it must be replaced.
095-112 MUSA 1ed GB 10-07-2008 9:37 Pagina 99

114
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
STARTING
THE ENGINE
The car is provided with an electronic
engine lock device: refer to “The Lan-
cia CODE system” paragraph in
“Dashboard and controls” if you can-
not start the engine. The engine may
be noisier during the first seconds of
operation, particularly after a long pe-
riod of inactivity. This does not impair
functionality and reliability and is
typical of hydraulic tappets: the dis-
tribution system selected for the petrol
engines of your car in order to limit
the maintenance required.
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
❒ensure that the handbrake is up;
❒put the gear lever into neutral;
❒press the clutch pedal down to the
floor without touching the accel-
erator;
❒turn the ignition to AV Vand re-
lease the key as soon as the engine
starts.If the engine does not start at the first
attempt, return the ignition key to
STOPbefore repeating starting.
If, when the ignition key is on MAR,
the instrument panel warning light
Yremains on together with the
warning light U, turn the key to
STOPand then back to MAR; if the
warning light remains on, try with the
other keys provided with the car.
Is is dangerous to let the en-
gine run in enclosed spaces.
The engine depletes the oxygen and
discharges carbon dioxide, carbon
monoxide and other toxic gases.
WARNING
In the first period of use, we
recommend to avoid exces-
sive stress for the car (for in-
stance excessive accelera-
tions, extended travel at maximum
speed, sudden braking etc.).
With engine off, do not leave
the key in the ignition switch
on MAR to prevent draining
the battery.
If you still cannot start the engine,
perform emergency start (see “Emer-
gency start” in chapter “In an emer-
gency”) and then contact a Lancia
Dealership.
IMPORTANT Never leave the ignition
key to MARwhen the engine is off.
STARTING PROCEDURE FOR
MULTIJET VERSIONS
Proceed as follows:
❒ensure that the handbrake is up;
❒put the gear lever into neutral;
❒turn the ignition key to MAR; the
instrument panel warning lights
m,
UandY;
113-124 MUSA 1ed GB 10-07-2008 9:37 Pagina 114