2009 INFINITI QX56 engine

BODY REPAIRBRM-23
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
BRM
N
O P
Engine Compartment
LIIA1506E
Revision: December 20092009 QX56

CCS
INSPECTION AND ADJUSTMENTCCS-5
< BASIC INSPECTION >
C
DE
F
G H
I
J
K L
M B
N P A
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPL ACING CONTROL UNIT : Description
INFOID:0000000003776923
Always perform the laser beam aiming adjustment after repl acing the ICC unit. In addition, test the ICC sys-
tem operations to see if it functions normally.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003776924
1.LASER BEAM AIMING ADJUSTMENT
Adjust laser beam aiming. Refer to CCS-5, "
LASER BEAM AIMING ADJUSTMENT : Outline of Laser Beam
Aiming Adjustment Procedure".
>> GO TO 2
2.ICC SYSTEM ACTION TEST
1. Perform the ICC system operation test. Refer to CCS-8, "
ACTION TEST : ICC System Running Test".
2. Check that the ICC system operates normally.
>> INSPECTION END.
LASER BEAM AIMI NG ADJUSTMENT
LASER BEAM AIMING ADJUSTMENT : Outlin e of Laser Beam Aiming Adjustment
Procedure
INFOID:0000000003776925
CAUTION:
• The laser beam aiming adjustment can not be performed without CONSULT-III.
• The laser beam aiming adjustment must be performed every time the ICC sensor is removed,
installed or has been moved as a result of a collision.
1. Prepare the vehicle and the work area.
2. Set up the ICC target board. For details, refer to Technical Service Bulletin.
3. Adjust the sensor following the procedure on CONSULT-III.
4. Check system operation after the adjustment.
LASER BEAM AIMING ADJU STMENT : PreparationINFOID:0000000003776926
• Place the vehicle on level ground. Shift the transmi ssion into "P" position and release the parking brake.
• Adjust the tire pressure to the specified value.
• See that there is no load in the vehicle. Coolant , engine oil and fuel should be filled to correct level.
• Check that the vehicle suspension has been adjusted to the standard height by the load leveling rear air sus-
pension system. Refer to SCS-7, "
CONSULT-III Function" .
• Clean the sensor with a soft cloth. Tool number : KV99110100 (J-45718)
LKIA0632E
Revision: December 20092009 QX56

CCS
INSPECTION AND ADJUSTMENTCCS-9
< BASIC INSPECTION >
C
DE
F
G H
I
J
K L
M B
N P A
• When there is no vehicle ahead, drive at the set speed steadily.
• When there is a vehicle ahead, control to maintain distance from the vehicle ahead, watching its speed.
• The set vehicle speed is displayed on the ICC system indicator in the combination meter.
CHECK FOR INCREASE OF THE CRUISING SPEED
1. Set vehicle-to-vehicle distance control mode at desired speed.
2. Check if the set speed increases by 1.6 km /h (1 MPH) as ACCEL/RES switch is pushed.
NOTE:
The maximum set speed of the vehicle-to-vehicl e distance control mode is 144 km/h (89 MPH).
CHECK FOR DECREASE OF THE CRUISING SPEED
1. Set vehicle-to-vehicle distance control mode at desired speed.
2. Check if the set speed decreases by 1.6 km /h (1 MPH) as COAST/SET switch is pushed.
NOTE:
• Vehicle-to-vehicle distance control mode is automatica lly turned off when the driving speed lowers to 32 km/
h (20 MPH) due to the deceleration of the vehicle ahead.
• The minimum set speed of the vehicle-to-vehicle distance control mode is 40 km/h (25 MPH).
CHECK FOR THE CANCELLATION OF VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE (NORMAL DRIV-
ING CONDITION) IN THE FOLLOWING CASES:
1. When the brake pedal is depressed after the system is turned on.
2. When the selector lever is shifted to the "N" (Neutral) position.
3. When the system is turned off.
4. When CANCEL switch is operated.
CHECK FOR RESTORING THE SPEED THAT IS SET BY VEHICLE-TO-VEHICLE DI STANCE CONTROL MODE
BEFORE CANCELLATION
1. Cancel the system by depressing the brake. Then, check that the speed before cancellation is restored
when pressing ACCEL/RES switch with vehi cle speed at 40 km/h (25 MPH) or above.
2. Cancel the system by shifting the selector lever to “N”. Then, check if the speed set before the cancella-
tion is restored when ACCEL/RES switch is pressed.
3. Check if the speed previously set is restored w hen ACCEL/RES switch is operated when driving 40 km/h
(25 MPH) or above, after canceling vehicle-to-v ehicle distance control mode by operating the CANCEL
switch.
CHECK ON/OFF SWITCH OPERATION
1. Start the engine. Then, check that the following operations are performed correctly.
2. Vehicle-to-vehicle distance control mode is displayed when ON/ OFF switch is pressed ON. Vehicle-to-vehicle distance control
mode goes off when ON/OFF switch is turned to OFF.
3. Turn off the ignition switch while ON/OFF switch is ON. Turn the ignition switch back to ON and confirm that CRUISE lamp and
ICC system display are OFF.
CHECK FOR ACCEL/RES, COAST/SET, CANCEL SWITCHES
1. Check if ACCEL/RES, COAST/SET, CANCEL sw itches operate smoothly.
2. Check if switch buttons r ebound as the buttons are released.
CHECK FOR DISTANCE SWITCH
1. Start the engine.
2. Press the ON/OFF switch for less than 1.5 seconds.
3. Press the DISTANCE switch.
4. Check if the set distance indicator changes display in order of:
(long) →(middle)→ (short).
NOTE:
ALOIA0012ZZ
Revision: December 20092009 QX56

CCS-10
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
The set distance indicator shows long immediately after the engine starts.
CONVENTIONAL (FIXED SPEED) CRUISE CONTROL MODE
SET CHECKING
1. Press the ON/OFF switch for more than 1.5 seconds.
2. Drive the vehicle between 40 km/h (25 MPH) and 144 km/h (89 MPH).
3. Push the COAST/SET switch.
4. Confirm that the desired speed is set when the COAST/SET switch is released.
NOTE:
• ICC system display in the combination meter shows nothing.
CHECK FOR INCREASE OF THE CRUISING SPEED
1. Set the conventional (fixed speed) cruise control mode at desired speed.
2. Check if the set speed increases by 1.6 km /h (1 MPH) as ACCEL/RES switch is pushed.
NOTE:
• If the ACCEL/RES switch is held, the vehicl e speed increases until the switch is released.
• The maximum set speed is 144 km/h (89 MPH).
CHECK FOR DECREASE OF THE CRUISING SPEED
1. Set the conventional (fixed speed) cruise control mode at desired speed.
2. Check if the set speed decreases by 1.6 km /h (1 MPH) as COAST/SET switch is pushed.
NOTE:
• Conventional (fixed speed) cruise control mode is autom atically turned off when the driving speed lowers to
32 km/h (20 MPH).
• The lowest set speed is 40 km/h (25 MPH).
CHECK FOR THE CANCELLATION OF CONVENTIONAL (FIXED SPEED) CRUISE CO NTROL MODE (NORMAL
DRIVING CONDITION) IN THE FOLLOWING CASES:
Refer to "CHECK FOR THE CANCELLATION OF VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
(NORMAL DRIVING CONDITION) IN THE FOLLOWING CASES:" .
CHECK FOR RESTORING THE SPEED TH AT IS SET BY CONVENTIONAL (FIXED SPEED) CRUISE CONTROL
MODE BEFORE ICC CANCELLATION
Refer to "CHECK FOR RESTORING THE SPEED THAT IS SET BY VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE BEFORE CANCELLATION" .
CHECK ON/OFF SWITCH OPERATION
SKIA6178E
Revision: December 20092009 QX56

CCS
INSPECTION AND ADJUSTMENTCCS-11
< BASIC INSPECTION >
C
DE
F
G H
I
J
K L
M B
N P A
1. Start the engine. Then, check that the following operations are performed correctly.
2. CRUISE lamp illuminates and ICC system indicator goes off when ON/OFF switch is pressed ON for more than 1.5 seconds.
The CRUISE lamp goes off when ON/OFF switch is turned to
OFF.
3. Turn off the ignition switch while ON/OFF switch is ON. Turn the ignition switch back to ON and confirm that CRUISE lamp is
OFF.
CHECK FOR ACCEL/RES, COAST/SET, CANCEL SWITCHES
1. Check if ACCEL/RES, COAST/SET, CANCEL sw itches operate smoothly.
2. Check if switch buttons r ebound as the buttons are released.
ALOIA0012ZZ
Revision: December 20092009 QX56

CCS
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
CCS-17
< FUNCTION DIAGNOSIS >
C
D E
F
G H
I
J
K L
M B
N P A
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
Diagnosis DescriptionINFOID:0000000003776935
The ICC system includes the on board self-diagnosis functi on that allows the technician to check for any trou-
ble codes on the ICC system display by operating the ICC steering switch.
ON BOARD SELF-DIAGNOSIS OPERETION PROCEDURE
1. Turn ignition switch OFF.
2. Start engine.
3. From 5 seconds through 15 seconds after start engine, press
RESUME/ACCELERATE switch 5 times, and SET/COAST
switch 5 times.
NOTE:
• Never turn the MAIN switch ON.
• When operation above is not completed from 5 secondsthrough 15 seconds, start again from above go to 1.
4. When the on board self-diagnosis starts up, the ICC system display shows DTC No. (1) at the set vehicle speed indicator. Refer to CCS-55, "
Diagnostic Trouble Code (DTC) Chart".
NOTE:
• DTC will disappear after 5 minutes.
• When more than one malfunction is detected, a maxi mum of 3 code numbers can be stored; the latest
malfunction will be displayed first.
WHEN ON BOARD SELF-DIAGNOSIS WILL NOT START UP
If the on board self-diagnosis does not start up, check the following items.
PKIB8371E
JSOIA0008GB
Assumed abnormal point Inspection item
ICC steering switch malfunction. Perform the inspection for DTC 46 OPERATION SW CIRC. Refer to CCS-30, "
DTC
46 OPERATION SW CIRC" .
Harness malfunction between ICC
steering switch and ECM.
ECM malfunction.
ICC unit malfunction. • Inspect the ICC sensor power and ground circuits. Refer to
CCS-25, "
DTC 31
POWER SUPPLY CIR1, DTC 34 POWER SUPPLY CIR2"
• Perform the self-diagnosis for the ICC unit with CONSULT-III, and check the diag-
nosis results. Refer to CCS-55, "
Diagnostic Trouble Code (DTC) Chart".
Revision: December 20092009 QX56

CCS-18
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
ERASING ON BOARD SELF-DIAGNOSIS
1. Stop the vehicle and turn ignition switch OFF.
2. Start engine and start on board self-diagnosis.
3. During on board self-diagnosis, press CANCEL switch 5 times,
and DISTANCE switch 5 times in this order.
NOTE:
• Press them within 10 seconds after pressing CANCEL switch
at first.
• When operation is not completed within 10 seconds, start again from step 2 above.
4. DTC 55 will be shown. NOTE:
DTC of an existing malfunction will not be erased.
5. Turn ignition switch OFF to exit the diagnosis.
CONSULT-III Function (ICC)INFOID:0000000003776936
DESCRIPTION
CONSULT-III can display each diagnostic item us ing the diagnostic test modes shown following.
WORK SUPPORT
Cause of Auto-Cancel Display Item List
×: Applicable
PKIB8373E
Test mode Function
Work Support • Monitors aiming direction to facilitate laser beam aiming operation.
• Indicates causes of automatic cancellation of the ICC system.
Self Diagnostic Result Displays malfunctioning system memorized in ICC sensor integrated unit.
Data Monitor Displays real-time input/output data of ICC sensor integrated unit.
Active Test Enables operation check of electrical loads by sending driving signal to them.
ECU Identification Displays part number of ICC sensor integrated unit.
Work support item Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
For the adjustment procedure, refer to
CCS-5, "
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement".
Cause of cancellationVehicle-to-vehi-
cle distance
control modeConventional
(fixed speed)
cruise control
mode
Description
OPERATING WIPER ×Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ×ABS function was operated.
OPERATING TCS ××TCS function was operated.
OPERATING VDC ××VDC function was operated.
OPE SW VOLT CIRC ××Outside the standard control switch input voltage was detected.
ECM CIRCUIT ××ECM did not permit ICC operation.
LASER SUN BEAM ×Intense light such as sunlight entered ICC sensor integrated unit
light sensing part.
LASER TEMP ×Temperature around ICC sensor integrated unit became low.
OP SW DOUBLE TOUCH ××ICC steering switches were pressed at the same time.
WHL SPD ELEC NOISE ××Wheel speed sensor signal caught electromagnetic noise.
Revision: December 20092009 QX56

CCS-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (ICC SENSOR INTEGRATED UNIT)
BRAKE SW
[On/Off] ××
Indicates [On/Off] status as judged from ICC brake switch signal (ECM trans-
mits ICC brake switch signal through CAN communication).
STOP LAMP SW
[On/Off] ××Indicates [On/Off] status as judged from stop lamp switch signal (ECM trans-
mits stop lamp switch signal through CAN communication).
CRUISE LAMP
[On/Off] ××
Indicates [On/Off] status of MAIN switch indicator lamp output.
CLUTCH SW SIG
[On/Off] ××
NOTE:
This item is displayed, but cannot monitor.
NP SW SIG
[On/Off] ××Indicates [On/Off] status as judged from transmission range switch signal
(ECM transmits transmission range switch signal through CAN communica-
tion).
STP LMP DRIVE
[On/Off] ××
Indicates [On/Off] status of ICC brake hold relay drive output.
PWR SUP MONI
[V] ××
Indicates IGN voltage input by ICC sensor integrated unit.
IDLE SW
[On/Off] ×Indicates [On/Off] status of idle switch read from ICC sensor integrated unit
through CAN communication (ECM transmits On/Off status through CAN
communication).
OWN VHCL
[On/Off] ×
Indicates [On/Off] status of own vehicle indicator output.
VHCL AHEAD
[On/Off] ×
Indicates [On/Off] status of vehicle ahead detection indicator output.
ICC WARNING
[On/Off] ×
Indicates [On/Off] status of ICC system warning lamp output.
BUZZER O/P
[On/Off] ×
Indicates [On/Off] status of ICC warning chime output.
ENGINE RPM
[rpm] ×Indicates engine speed read from ICC sensor integrated unit through CAN
communication (ECM transmits engine speed through CAN communication).
WIPER SW
[OFF/LOW/HIGH] ×
Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front wiper request
signal through CAN communication).
YAW R AT E
[deg/s] ×NOTE:
This item is displayed, but cannot monitor.
D RANGE SW
[On/Off] ×Indicates [On/Off] status of “D” or “DS” or “M” positions read from ICC sensor
integrated unit through CAN communication; ON when position “D” or “DS” or
“M” (TCM transmits shift position indicator lamp signal through CAN commu-
nication).
NP RANGE SW
[On/Off] ×Indicates shift position indicator lamp signal read from ICC sensor integrated
unit through CAN communication (TCM transmits shift position indicator lamp
signal through CAN communication).
VHCL SPD AT
[km/h] or [mph] ×Indicates vehicle speed calculated from A/T vehicle speed sensor read from
ICC sensor integrated unit through CAN communication (TCM transmits A/T
vehicle speed sensor signal through CAN communication).
GEAR
[1, 2, 3, 4, 5] ×Indicates A/T gear position read from ICC sensor integrated unit through CAN
communication (TCM transmits current gear position signal through CAN
communication).
MODE SIG
[OFF, ICC, ASCD] ×Indicates the active mode from ICC or ASCD [conventional (fixed speed)
cruise control mode].
SET DISP IND
[On/Off] ×
Indicates [On/Off] status of SET switch indicator output.
DISTANCE
[m] ×
Indic

ates the distance from the vehicle ahead.
RELATIVE SPD
[m/s] ×
Indicates the relative speed of the vehicle ahead.
Monitored Item [unit]
MAIN
SIGNALS SELECTION
FROM
MENU Description
Revision: December 20092009 QX56