2009 HUMMER H3 wheel

5. Simultaneously press and hold
the Four-Wheel High and
Four-Wheel-Low Lock buttons for
10 seconds. The Neutral light
will come on when the transfer
case shift to Neutral is complete.
6. Press and hold the regular brake
pedal and shift the transmission
to R (Reverse), then shift the
transmission to D (Drive) for an
automatic transmission, or
1 (First) for vehicles have a
manual transmission and then let
out the clutch. This is to ensure
the transfer case is in Neutral.
If not, repeat this procedure
starting at Step 3.
7. Turn the engine off.
8. Place the transmission shift lever
in P (Park) for an automatic
transmission, or 1 (First) for
vehicles that have a manual
transmission.
9. Turn the ignition to LOCK/OFF.Shifting Out of Neutral
To shift out of Neutral:
1. Set the parking brake and apply
the regular brake pedal.
2. Shift the transmission to
N (Neutral) for an automatic
transmission, or press the clutch
pedal for vehicles that have a
manual transmission. Then turn
the ignition to ON/RUN but
do not start the engine.
3. Press the button for the desired
transfer case shift position
(Four-Wheel High,
Four-Wheel-High Lock or
Four-Wheel-Low Lock).
After the transfer case has
shifted out of Neutral the light
will go out.
4. Release the parking brake.Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
5. You may start the engine and
shift the transmission to the
desired position.
Features and Controls 2-27

Shifting Into Park
(Automatic Transmission)
{CAUTION
It can be dangerous to get out of
the vehicle if the shift lever is not
fully in P (Park) with the parking
brake rmly set. The vehicle can
roll. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, use the steps
that follow. If you are pulling a
trailer, seeTowing a Trailer on
page 4-42.
1. Hold the brake pedal down,
then set the parking brake.
SeeParking Brake on page 2-28
for more information.
{CAUTION
With all-wheel drive, the vehicle
will be free to roll — even if the
shift lever is in P (Park) — if the
transfer case is in Neutral. So, be
sure the transfer case is in a drive
gear, four-wheel high (4H) or
four-wheel low (4L) — not in
Neutral.
2. Move the shift lever into P (Park)
by pressing the shift lever button
and moving the lever as far
forward as it will go.
3. Turn the ignition key to
LOCK/OFF.
4. Remove the key from the
ignition.
Leaving Your Vehicle
With the Engine Running
(Automatic Transmission)
{CAUTION
It can be dangerous to leave the
vehicle with the engine running.
The vehicle could move suddenly
if the shift lever is not fully in
P (Park) with the parking brake
rmly set. And, if you leave the
vehicle with the engine running,
it could overheat and even catch
re. You or others could be
injured. Do not leave the vehicle
with the engine running.
If you have to leave the vehicle with
the engine running, be sure the
vehicle is in P (Park) and the parking
brake is rmly set before you
leave it. After you have moved the
shift lever into P (Park), hold
the regular brake pedal down.
Features and Controls 2-29

Instrument Panel
Instrument Panel
Overview
Instrument Panel
Overview...........................3-4
Hazard Warning Flashers. . .3-5
Horn...................................3-5
Tilt Wheel...........................3-6
Turn Signal/Multifunction
Lever................................3-6
Turn and Lane-Change
Signals.............................3-6
Headlamp High/
Low-Beam Changer..........3-7
Flash-to-Pass......................3-7
Windshield Wipers..............3-7
Windshield Washer.............3-8
Rear Window Wiper/
Washer.............................3-8
Cruise Control....................3-9
Exterior Lamps..................3-11
Headlamps on Reminder. . .3-13
Daytime Running
Lamps (DRL)..................3-13
Automatic Headlamp
System............................3-14
Off-Road Lamps................3-14
Fog Lamps.......................3-15
Instrument Panel
Brightness.......................3-15
Dome Lamp......................3-16
Dome Lamp Override........3-16
Exit Lighting......................3-16
Reading Lamps.................3-16
Electric Power
Management...................3-17
Battery Run-Down
Protection........................3-17
Accessory Power
Outlet(s)..........................3-18
Ashtray(s) and Cigarette
Lighter.............................3-18
Climate Controls
Climate Control System. . . .3-19
Outlet Adjustment.............3-21
Warning Lights, Gages,
and Indicators
Warning Lights, Gages,
and Indicators.................3-22
Instrument Panel Cluster. . .3-23
Speedometer and
Odometer........................3-24
Trip Odometer..................3-24
Tachometer.......................3-24
Safety Belt Reminders......3-24
Airbag Readiness Light.....3-25
Passenger Airbag Status
Indicator..........................3-26
Charging System Light......3-27
Up-Shift Light....................3-27
Brake System Warning
Light................................3-27
Antilock Brake System
(ABS) Warning Light.......3-28
StabiliTrak®/Traction
Control System (TCS)
Warning Light
..................3-29
Engine Coolant
Temperature Gage..........3-29
Tire Pressure Light...........3-30
Malfunction
Indicator Lamp................3-30
Instrument Panel 3-1

The main components of the
instrument panel are the following:
A.Outlet Adjustment on page 3-21.
B.Turn Signal/Multifunction Lever
on page 3-6.Windshield Wipers
on page 3-7.Windshield Washer
on page 3-8.Cruise Control on
page 3-9.
C.Horn on page 3-5.
D.Instrument Panel Cluster on
page 3-23.
E.Hazard Warning Flashers on
page 3-5.
F.Full-Time Four-Wheel Drive on
page 2-24.Passenger Airbag
Status Indicator on page 3-26.
Locking Rear Axle on page 4-8.
Locking Front Axle on page 4-9
(If Equipped) orTraction Control
System (TCS) on page 4-7.
G.Exterior Lamps on page 3-11.
Dome Lamp Override on
page 3-16.Instrument Panel
Brightness on page 3-15.
Fog Lamps on page 3-15.
OnStar
®System on page 2-39
andBluetooth®on page 3-52.H.Parking Brake on page 2-28.
I.Audio System(s) on page 3-41.
J.Climate Control System on
page 3-19.
K.Rear Window Wiper/Washer on
page 3-8(If Equipped).
L.Traction Control System (TCS)
on page 4-7(For vehicles with
Locking Front Axle).
M.Off-Road Lamps on page 3-14.
N. Shift Lever. SeeAutomatic
Transmission Operation on
page 2-19orManual
Transmission Operation on
page 2-22.
O.Accessory Power Outlet(s) on
page 3-18.
P.Glove Box on page 2-47.
Hazard Warning Flashers
|
(Hazard Warning Flasher):
Press this button located on
the instrument panel, to make the
front and rear turn signal lamps ash
on and off. This warns others that
you are having trouble.
Press
|again to turn the
ashers off.
Horn
To sound the horn, press the horn
symbol on the steering wheel pad.
Instrument Panel 3-5

Tilt Wheel
A tilt wheel allows the steering
wheel to be adjusted.
The tilt lever is located on the left
side of the steering column.
To tilt, hold the steering wheel and
pull the tilt lever toward you.
Raise or lower the wheel to a
comfortable level, then release the
tilt lever to lock the wheel in
place.
Do not adjust the steering wheel
while driving.
Turn Signal/Multifunction
Lever
The lever on the left side of the
steering column includes the
following:
G: Turn and Lane Change
Signals
53: Headlamp High/Low-Beam
Changer
N: Windshield Wipers
L: Windshield Washer
J: Cruise Control
Flash-to-Pass.
Information for these features is on
the pages following.
Turn and Lane-Change
Signals
An arrow on the instrument panel
cluster ashes in the direction of the
turn or lane change.
Move the lever all the way up or
down to signal a turn.
Raise or lower the lever until the
arrow starts to ash to signal a lane
change. Hold it there until the
change is completed.
The lever returns to its starting
position whenever it is released.
If after signaling a turn or a
lane change the arrow ashes
rapidly or does not come on,
a signal bulb may be burned out.
3-6 Instrument Panel

The rear window washer uses the
same uid bottle as the windshield
washer. Check the uid level if
the windshield can be washed, but
the rear windows cannot.
Cruise Control
With cruise control, a speed of
about 25 mph (40 km/h) or more can
be maintained without keeping
your foot on the accelerator. Cruise
control does not work at speeds
below about 25 mph (40 km/h).
9(Off):Turns the cruise control
system off.
R(On):Turns the cruise control the
system on.
S(Resume/Accelerate):This
position makes the vehicle
accelerate or resume to a previously
set speed.
rT(Set):Press this button to
set the speed.
Cruise control will not work if the
parking brake is set, or if the master
cylinder brake uid level is low.
If the brakes are applied, the cruise
control shuts off.
{CAUTION
Cruise control can be dangerous
where you cannot drive safely at
a steady speed. So, do not use
the cruise control on winding
roads or in heavy traffic.
Cruise control can be dangerous
on slippery roads. On such roads,
fast changes in tire traction can
cause excessive wheel slip, and
you could lose control. Do not use
cruise control on slippery roads.
The cruise control disengages, if the
vehicle has the Traction Control
System (TCS) and it begins to limit
wheel spin. SeeTraction Control
System (TCS) on page 4-7.
When road conditions allow the
cruise control to be safely used
again, you can turn it back on.
Instrument Panel 3-9

Reducing Speed While Using
Cruise Control
Press and holdTuntil the
desired lower speed is reached,
then release it.
To slow down in very small
amounts, briey press
T. Each
time this is done, the vehicle
goes about 1 mph (1.6 km/h)
slower.
Passing Another Vehicle While
Using Cruise Control
Use the accelerator pedal to
increase the vehicle speed. When
you take your foot off the pedal, the
vehicle slows down to the cruise
control speed set earlier.Using Cruise Control on Hills
How well the cruise control works on
hills depends upon the vehicle’s
speed, load, and the steepness of
the hills. When going up steep
hills, the accelerator pedal might
have to be used to maintain
the vehicle speed. When going
downhill, you might have to brake or
shift to a lower gear to keep the
vehicle speed down. When
the brake is applied the cruise
control will turn off.
Ending Cruise Control
To turn off the cruise control, do
one of the following:
Step lightly on the brake pedal.
Move the cruise control switch
to
9.
Lightly tap or press the clutch, if
the vehicle has a manual
transmission.Erasing Speed Memory
The cruise control set speed memory
is erased, when the cruise control or
the ignition is turned off.
Exterior Lamps
The exterior lamps control is located
on the instrument panel to the left
of the steering wheel.
O(Exterior Lamps):Turn the
knob to select one of the four
exterior lamp positions.
Instrument Panel 3-11

The off-road lamps button is located
on the instrument panel below
the climate controls.
To use the lamps, remove the
covers from the lamps and press
the button to turn them on or off. An
indicator light turns on when the
lamps are on.
Notice:Turning on the off-road
lamps before removing the
lamp covers could damage the
off-road lamps and the covers.
Always remove the covers before
turning on the off-road lamps. The off-road lamps remain on even
after the ignition is turned off.
The off-road lamp button must be
pressed to turn them off.
Fog Lamps
The vehicle has fog lamps that
provide better visibility in foggy or
misty conditions.
The fog lamp button is located in
the exterior lamps control.
#(Fog Lamps):
The headlamps
or parking lamps must be on for
the fog lamps to work. Press
#to turn the fog lamps on or off. An
indicator light turns on when the fog
lamps are on.
Never use the fog lamps in the dark
without turning on the headlamps.
When the high-beam headlamps are
turned on, the fog lamps turn off
automatically. When the high-beam
headlamps are turned off, the
fog lamps come on again.
Some localities have laws that
require the headlamps to be
on along with the fog lamps.
Instrument Panel
Brightness
This feature controls the brightness
of the instrument panel lights.
The instrument panel brightness
thumbwheel is located next to
the exterior lamp control.
D(Instrument Panel Brightness):
Turn the thumbwheel up or down
to brighten or dim the instrument
panel lights and the radio display.
Instrument Panel 3-15