2009 HUMMER H3 lock

7. Turn the vertical aiming screw
until the headlamp beam is
aimed to the horizontal tape
line. Turn it clockwise or
counterclockwise to raise or
lower the beam.
The top edge of the cut-off
should be positioned at the
bottom edge of the horizontal
tape line.
8. Repeat Steps 7 and 8 for the
opposite headlamp.
Bulb Replacement
For the proper type of replacement
bulbs, seeReplacement Bulbs
on page 5-43.
For any bulb changing procedure
not listed in this section, contact
your dealer/retailer.
Halogen Bulbs
{CAUTION
Halogen bulbs have pressurized
gas inside and can burst if you
drop or scratch the bulb. You or
others could be injured. Be sure
to read and follow the instructions
on the bulb package.
Headlamps
To replace a headlamp bulb:
1. Open the hood. SeeHood
Release on page 5-9for
more information.
2. Turn the bulb socket
counterclockwise to remove it
from the headlamp assembly
and pull it straight out.
3. Unplug the electrical connector
by pushing the release tab and
pulling the bulb socket out.
4. Replace with a new bulb socket.
5. Reverse Steps 1 through 3 to
reinstall.
Service and Appearance Care 5-41

Taillamps, Turn Signal,
Stoplamps and Back-up
Lamps (H3)
A. Stoplamp, Taillamp and Turn
Signal Lamp
B. Back-up LampTo replace one of these bulbs in the
taillamp assembly:
1. Open the swing-gate.
SeeSwing-gate on page 2-9.
2. Remove the two screws from the
taillamp assembly.
3. Pull the taillamp assembly away
from the vehicle.
4. Turn the bulb socket
counterclockwise to remove it
from the taillamp assembly.5. Pull the old bulb to release it
from the socket.
6. Reverse Steps 1 through 4 to
reinstall.
Taillamps, Turn Signal,
Stoplamps and Back-up
Lamps (H3T)
A. Stoplamp and Taillamp
B. Turn Signal Lamp
C. Back-up Lamp
Passenger Side Shown
5-42 Service and Appearance Care

To replace one of these bulbs in the
taillamp assembly:
1. Open the tailgate. SeeTailgate
on page 2-7.
2. Remove the two screws from the
taillamp assembly.
3. Pull the taillamp assembly away
from the vehicle.
4. Turn the bulb socket
counterclockwise to remove it
from the taillamp assembly.
5. Pull the old bulb to release it
from the socket.6. Turn the bulb socket clockwise to
reinstall in the taillamp assembly.
7. Reinstall the taillamp assembly
making sure to line up the pins
with the vehicle.
8. Reinstall the two screws.
License Plate Lamp
To replace one of these bulbs:
1. Remove the two screws holding
the license plate lamp.
2. Pull the license plate lamp away
from the fascia.
3. Turn the bulb socket
counterclockwise and pull the
bulb straight out of the license
plate lamp assembly.4. Install the new bulb into the
socket.
5. Reverse Steps 1 through 4 to
reinstall.
Replacement Bulbs
Exterior LampBulb
Number
Back-up Lamp (H3T) W16W
Back-up (H3),
Stoplamp,
Taillamp and Turn
Signal Lamp3157K
License Plate Lamp 194
Low-Beam and
High-Beam
HeadlampH13
For replacement bulbs not listed
here, contact your dealer/retailer.
Service and Appearance Care 5-43

TPMS Sensor Matching
Process
Each TPMS sensor has a unique
identication code. Any time
you replace one or more of the
TPMS sensors or rotate the
vehicle’s tires, the identication
codes need to be matched to the
new tire/wheel position. The sensors
are matched to the tire/wheel
positions in the following order:
driver side front tire, passenger side
front tire, passenger side rear
tire, and driver side rear tire using a
TPMS diagnostic tool. See your
dealer/retailer for service.
The TPMS sensors can also be
matched to each tire/wheel position
by increasing or decreasing the
tire’s air pressure. If increasing the
tire’s air pressure, do not exceed
the maximum ination pressure
indicated on the tire’s sidewall.
To let air-pressure out of a tire you
can use the pointed end of the
valve cap, a pencil-style air pressure
gage, or a key.You have one minute to match
the rst tire/wheel position,
and ve minutes overall, to match
all four tire/wheel positions. If it
takes longer than one minute, to
match the rst tire and wheel,
or more than ve minutes to match
all four tire and wheel positions,
the matching process stops and you
need to start over.
The TPMS sensor matching
procedure is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to
ON/RUN with the engine off.
3. Turn the exterior lamp switch
from AUTO to OFF four times
within three seconds. A double
horn chirp will sound and
the TPMS low tire warning light
starts ashing. The double
horn chirp and ashing TPMS
warning light indicates the
TPMS matching process has
started. The TPMS warning
light should continue ashingthroughout the matching
procedure. The LOW TIRE
message displays on the Driver
Information Center (DIC).
4. Start with the driver side front tire.
5. Remove the valve cap from the
valve cap stem. Activate the
TPMS sensor by increasing or
decreasing the tire’s air pressure
for 10 seconds, then stop and
listen for a single horn chirp.
The single horn chirp should
sound within 15 seconds,
conrming that the sensor
identication code has been
matched to this tire and wheel
position. If you do not hear
the conrming single horn chirp,
turn the ignition switch to
LOCK and start over beginning
with Step 2.
6. Proceed to the passenger side
front tire, and repeat the
procedure in Step 5.
7. Proceed to the passenger side
rear tire, and repeat the
procedure in Step 5.
5-56 Service and Appearance Care

8. Proceed to the driver side rear
tire, and repeat the procedure
in Step 5.
9. After hearing the conrming horn
chirp for the driver side rear tire,
check to see if the TPMS low tire
warning light and the DIC LOW
TIRE messages have turned off.
If yes, the TPMS sensors have
been relearned. Turn the ignition
switch to LOCK/OFF.
If the low tire warning light and
the SERV TPM message on the
DIC are on after completing
Step 5 for the driver side rear tire,
the sensor relearn process has
not been successful. Turn the
ignition switch to LOCK/OFF and
repeat the matching process
beginning with Step 2.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire,
for signs of wear or damage.
SeeWhen It Is Time for
New Tires on page 5-58for
more information.
Tires should be rotated
every 5,000 to 8,000 miles
(8 000 to 13 000 km).
SeeScheduled Maintenance
on page 6-4.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the
vehicle continues to perform
most like it did when the
tires were new.Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
SeeWhen It Is Time for
New Tires on page 5-58and
Wheel Replacement on
page 5-64.
Make sure the spare tire is
stored securely. Push, pull and
then try to rotate or turn the
tire. If it moves, use the wheel
wrench/hoist shaft to tighten
the cable. SeeChanging a
Flat Tire on page 5-66.
Service and Appearance Care 5-57

Vehicles equipped with a tire
pressure monitoring system may
give an inaccurate low-pressure
warning if non-TPC spec rated
tires are installed on your
vehicle. Non-TPC Spec rated
tires may give a low-pressure
warning that is higher or lower
than the proper warning level
you would get with TPC
Spec rated tires. SeeTire
Pressure Monitor System on
page 5-52.
Your vehicle’s original equipment
tires are listed on the Tire and
Loading Information Label.
SeeLoading the Vehicle
on page 4-35, for more
information about the Tire and
Loading Information Label
and its location on your vehicle.Different Size Tires and
Wheels
If you add wheels or tires that are a
different size than your original
equipment wheels and tires,
this could affect the way your vehicle
performs, including its braking,
ride and handling characteristics,
stability, and resistance to rollover.
Additionally, if your vehicle has
electronic systems such as anti-lock
brakes, rollover airbags, traction
control, and electronic stability
control, the performance of these
systems can be affected.
{CAUTION
If you add different sized
wheels, your vehicle may not
provide an acceptable level of
performance and safety if tires not
recommended for those wheels
are selected. You may increase
the chance that you will crash and
suffer serious injury. Only use GM
specic wheel and tire systems
developed for your vehicle, and
have them properly installed by a
GM certied technician.
SeeBuying New Tires on page 5-59
andAccessories and Modifications
on page 5-3for additional
information.
Service and Appearance Care 5-61

CAUTION (Continued)
3. If you have a
four-wheel-drive vehicle,
be sure the transfer case
is in a drive gear – not in
N (Neutral).
4. Turn off the engine and do
not restart while the vehicle
is raised.
5. Do not allow passengers to
remain in the vehicle.
To be even more certain the
vehicle will not move, put blocks
at the front and rear of the tire
farthest away from the one being
changed. That would be the tire
on the other side, at the opposite
end of the vehicle.When the vehicle has a at tire,
the wheel blocks need to be set up
before changing it. The wheel
blocks are located in the tool bag in
the swing-gate for H3 models or
below the rear seat for H3T models.
SeeRemoving the Spare Tire
and Tools (H3) on page 5-68or
Removing the Spare Tire and
Tools (H3T) on page 5-69for
more information.
To use the wheel blocks, lift the
wheel block and lock it into place.Use the following example as a
guide to assist in the placement of
the wheel blocks (A) when the
vehicle has a at tire (B).
A. Wheel Block
B. Flat Tire
The following information explains
how to use the jack and change
a tire.
Service and Appearance Care 5-67

Removing the Spare Tire
and Tools (H3)
The equipment needed is located in
the swing-gate, behind a cover.
To remove the equipment:
1. Open the swing-gate.
SeeSwing-gate on page 2-9.
2. Remove the cover, located on
the inside of the swing-gate,
by lifting the two latches.
3. Turn the wing nut
counterclockwise to release
the jack tool bag and jack
and remove them.4. Undo the straps that secure the
jack tool bag to the jack.
5. Open the tool bag to nd the
following tools, which are
used to remove the spare tire
and at tire:
A. Wheel Wrench
B. Jack Handle Extensions
C. Jack Handle
D. Jack
E. Wheel BlocksThe spare tire is attached to the
outside of the swing-gate.
To remove the spare tire:
1. If the vehicle has a spare tire
cover release the latch by
pulling the latch straight back
and turning it away from
the cover at the same time.
Notice:Opening the endgate
before completely closing and
latching the spare tire cover may
result in damage to your vehicle.
Close and latch the spare tire
cover before opening the endgate
to avoid possible damage.
5-68 Service and Appearance Care