2009 HUMMER H2 spare wheel

Removing the Spare Tire and
Tools (SUT)
The jack is stored in the rear cargo compartment on the
passenger side of the vehicle. The tools for the jack
are stored under the rear passenger’s seat.
To remove the tools:
1. Locate the tools by lifting the driver’s side second
row seat up to expose the oor.
2. Remove the strap from the seat rail. Then carefully
slide the tool bag out from under the seat rail as
shown.
Take care to not pinch the seat cables or electrical
harnesses.3. Open the tool bag. You will nd the following tools
needed to remove the spare tire and at tire:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel Blocks
5-82

Remove the wheel blocks
from the tool bag. Then
lift the wheel block
as shown to lock it
into place.Removing the Spare Tire (SUT)
The spare tire is attached to the tire carrier. To remove
the spare tire:
In order to remove the spare tire, you may need
someone to assist you.
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.
5-84

3. Pull off the license plate holder from the spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts.
5. Turn the wheel wrench with the wheel wrench
extender counterclockwise to loosen the wheel nuts.6. Remove the wheel nuts holding the spare tire onto
the tire carrier.
7. Pull off the spare tire and gently lower to the
ground. Set it next to the at tire.
5-85

Removing the Spare Tire and
Tools (SUV)
Removing the Tools (SUV)
The equipment you will need to change a at tire is
stored under the storage tray, which is located on the
driver side trim panel (over the rear wheelhouse).
To remove the equipment:
1. Remove the tray to access the tools by pulling up
on the nger depression.2. Turn the retainer nut (C) counterclockwise. Remove
the tool bag (A) and the two wheel blocks (B) from
the storage area.
5-86

3. Open the tool bag. The following tools needed to
remove the spare tire and at tire are inside the
tool bag:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel Wrench
D. Wheel Wrench
ExtensionBefore proceeding, be sure to set the wheel blocks at
the appropriate tire as previously shown. To use
the wheel blocks:
Removing the Jack (SUV)
The jack is stored in the rear cargo area on the
driver side.
1. To access the jack pull on the two latches to
remove the trim cover.
5-87

2. Insert the wheel wrench into the hole and turn it
counterclockwise to release it.
3. Grasp and lift the jack out of the bracket.
Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier. To remove
the spare tire:
In order to remove the spare tire, you may need
someone to assist you.
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.
5-88

3. Pull off the license plate holder from the spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts. Turn the
wheel wrench with the wheel wrench extender
counterclockwise to loosen the wheel nuts.5. Remove the wheel nuts holding the spare tire onto
the tire carrier.
6. Pull off the spare tire and gently lower it to the
ground. Set it next to the at tire.
5-89

Removing the Flat Tire and
Installing the Spare Tire
Jack (SUV and SUT)
1. Do a safety check before proceeding. SeeChanging
a Flat Tire on page 5-80for more information.
2. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and carefully pry the
center cap out.
3. Attach the wheel wrench to the extender.4. Turn the wheel wrench counterclockwise to loosen
the wheel nuts. Do not remove them yet.
Now jack the vehicle up.
5-90