2009 HONDA CIVIC ECU

ÎÎ
This audio system can select and
play the audio f iles on a USB f lash
memory device with the same
controls used f or the disc player. To
play a USB f lash memory device,
connect it to the USB adapter cable
in the console compartment, then
press the AUX button. The ignition
switch must be in the ACCESSORY
(I) or ON (II) position.
The audio system reads and plays
the audio f iles on the USB f lash
memory device in MP3, WMA or
AAC f ormats. Depending on the
f ormat, the display shows MP3,
WMA or AAC when a USB flash
memory device is playing. The USB
f lash memory device limit is up to
700 f olders or up to 65535 f iles. Only AAC f ormat f iles recorded
with iTunes are playable on this
audio unit.
Do not use an extension cable to
the USB adapter cable equipped
with your vehicle.
Do not keep a USB f lash memory
device in the vehicle. Direct
sunlight and high heat will damage
it.
We recommend backing up your
data bef ore playing a USB f lash
memory device.
Depending on the type and
number of f iles, it may take some
time bef ore they begin to play.
Depending on the sof tware the
f iles were made with, it may not be
possibletoplaysomefiles,or
display some text data.
The recommended USB f lash
memory devices are 256 Mbyte or
higher. Some digital audio players
maybecompatibleaswell.
Some USB f lash memory device
(such as devices with security lock-
out f eatures, etc.) will not work in
this audio unit.
Do not use a device such as a
card reader or hard drive as the
device or your f iles may be
damaged.
Do not connect your USB f lash
memory device using a hub.:
To Play a USB Flash Memory
Device
Audio System (Models without navigation system)
142
NOTE:
——y

y
(#y
y

¼
When the USB f lash memory device
is connected, the USB indicator is
showninthedisplay.
Pull out the USB connector f rom
the holder and remove the cable
f rom the clip in the console
compartment.
Connect the USB f lash memory
device to the USB connector
correctly and securely.Each time you press the DISP button,
the display mode shows you in
sequence, the f older name, the f ile
name, the artist tag, the album tag,
the track tag and name off (which
turns off the text display).
The display shows up to 16
characters of the selected data. If the
text data has more than 16
characters, you will see the f irst 15
characters and the indicator in
the display. Press and hold the DISP
button until the next 16 characters
are shown.
1. 2.
Connect ing a USB Flash Memory
Device T ext Data Display Function
Audio System (Models without navigation system)
144
USB ADAPTER
CABLE
USB CONNECTOR
USB CONNECTOR
——y

y
(#y
y

ÎÎ
CONT INUED
Pull out the USB connector f rom
the holder and remove the cable
f rom the clip in the console
compartment.
Connect your dock connector to
the iPod correctly and securely.
Install the dock connector to the
USB adapter cable securely.
When the iPod is connected and the
iPod mode is selected on the audio
display, the iPod indicator is shown
on the screen. Af ter loading, you will
see Honda Logo mark on the iPod.
That means you can only operate
your iPod using the vehicle’s audio
unit. Itmaytakeafewminutesfor
the Honda mark to display on
the iPod. If the display does not
change, this f unction is not
supported on your iPod model
or f irmware.
1. 2. 3.
:
Connect ing an iPod
Audio System (Models with navigation system)
Features
185
DOCK CONNECTOR
USB ADAPTER CABLE USB CONNECTOR
Sample Display
USB CONNECTOR OK to disconnect
——y



y
(#y
y

ÎÎ
This audio system can select and
play the audio f iles f rom a USB f lash
memory device with the same
controls used f or the in-dash disc
player. To play a USB f lash memory
device, connect it to the USB adapter
cable in the console compartment.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Press the AUDIO button beside the
screen to show the audio display and
touch the AUX icon.
The audio system reads and plays
the audio f iles on the USB f lash
memory device in MP3, WMA or
AAC f ormats. Depending on the
f ormat, the display shows MP3,
WMA or AAC when a USB flash
memory device is playing. The USB
f lash memory device limit is up to
700 f olders or up to 65535 f iles. Only AAC f ormat f iles recorded
with iTunes are playable on this
audio unit.
The recommended USB f lash
memory devices are 256 Mbyte or
higher. Some digital audio players
maybecompatibleaswell.
Some USB f lash memory device
(such as devices with security lock-
out f eatures, etc.) will not work in
this audio unit. Do not use an extension cable to
the USB adapter cable equipped
with your vehicle.
Do not keep a USB f lash memory
device in the vehicle. Direct
sunlight and high heat will damage
it.
We recommend backing up your
data bef ore playing a USB f lash
memory device.
Depending on the type and
number of f iles, it may take some
time bef ore they begin to play.
Depending on the sof tware the
f iles were made with, it may not be
possibletoplaysomefiles,or
display some text data.
Do not use a device such as a card
reader or hard drive as the device
or your f iles may be damaged.
Do not connect your USB f lash
memory device using a hub.
:
CONT INUED
To Play a USB Flash Memory
Device
Audio System (Models with navigation system)
Features
191
NOTE:
——y

y
(#y
y

CONT INUED
Even if recorded in MP3, WMA or
AAC f ormat, a f ile with unsupported
version cannot be played. If the
system f inds it, the audio unit
displays UNSUPPORTED, and then
skips to the next f ile.
In WMA or AAC format, DRM
(digital rights management) f iles
cannot be played. If the system f inds
a DRM f ile, the audio unit displays
UNPLAYABLE FILE, and then skips
to the next file.Connect the USB f lash memory
device to the USB connector
correctly and securely.
When the USB f lash memory device
is connected and the USB mode is
selected on the audio system, the
WMAorMP3indicatorisshownon
the navigation screen. It also shows
the f older and f ile numbers, and the
elapsed time on the screen.
Pull out the USB connector f rom
the holder and remove the cable
f rom the clip in the console
compartment.
1.
2.
Audio System (Models with navigation system)
Connect ing a USB Flash Memory
Device
Features
193
USB ADAPTER CABLE USB CONNECTOR
USB CONNECTOR
——y
y
(#y
y

Once the security system is set,
opening any door, the trunk, or the
hood without using the key or the
remote transmitter will cause it to
alarm. It also alarms if the radio is
removed f rom the dashboard or the
wiring is cut.
The security system automatically
sets 15 seconds after you lock the
doors, hood, and trunk. For the
system to activate, you must lock the
doors f rom the outside with the key,
driver’s lock tab, door lock master
switch, or remote transmitter. The
security system indicator on the
instrument panel starts blinking
immediately to show you the system
is setting itself . With the system set, you can still
open the trunk with the master key
or the remote transmitter without
triggering the alarm. The alarm will
sound if the trunk lock is f orced, or
the trunk is opened with the trunk
release handle.
The security system will not set if
the hood, trunk, or any door is not
f ully closed. If the system will not set,
check the door and trunk open
indicators on the instrument panel
(see page ) to see if the doors and
trunk are f ully closed. Since it is not
part of the monitor display, manually
check the hood.
Do not attempt to alter this system
or add other devices to it.
To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, the horn will beep
once.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights (low beam), parking
lights, side marker lights, and
taillights f lash if someone attempts
to break into your vehicle or remove
the radio. This alarm continues f or 2
minutes, then it stops. To reset an
activated system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.
61
If equipped
Security System
Features
207
NOTE:
Except Si
Si
SECURITY SYSTEM INDICATOR
——y


y
(#y
y

When you pair your phone to HFL,
the HFL system will automatically
select a pairing code at random or in
order. You can customize this setting
mode between Random and Fixed. If
you select the f ixed mode, the HFL
system will select a pairing code
sequentially.Press and release the Talk button.
Af ter the beep, say ‘‘Set Pairing
Code.’’
HFL responds ‘‘Each time a phone
is paired with HandsFreeLink, a
pairing code is used f or security.
This code can be randomly
generated by HandsFreeLink, or
f ixed, which is needed f or some
Bluetooth devices with a preset
pairing code. Would you like to set
the pairing code as Random or
Fixed?’’
Press and release the Talk button.
Af ter the beep, to select the f ixed
mode, say ‘‘Fixed.’’
HFL responds ‘‘What is the f our-
digit number you would like to see
as the pairing code? Press the Talk
button and say the number.’’Press and release the Talk button.
Af ter the beep, say a desired f our-
digit number. For example, say‘‘1000.’’
HFL responds ‘‘1000. Is this
correct? Press the Talk button and
say Yes or No.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Phone setup.’’
HFL responds ‘‘Phone setup
options are pair, edit, delete, list,
status, next phone, and set pairing
code. Press the Talk button and
say a command.’’ If the number is not correct, say
‘‘No.’’ HFL goes back to step 3.
HFL responds ‘‘HandsFreeLink
willusethiscodewhenpairingtoa
Bluetooth device.’’
Press and release the Talk button.
Af ter the beep, if the number is
correct, say ‘‘Yes.’’
1. 2. 3.4. 5. 6.
To change the setting mode, do this:
Bluet oot hHandsFreeL ink
Set t ing a Pairing Code
222
——y
y
(#yy

CONT INUED
You can select or change some
settings for the HFL system. Here
are the settings you can select or
change. To do this, make sure your
vehicle is parked safely, with your
phone on and the ignition switch in
the ACCESSORY (I) or ON (II)
position.You can set a f our-digit security
passcode to lock the HFL system
f or security purposes.
If you f orget your passcode, you
cannot activate HFL. Consult your
dealer to cancel the passcode. The incoming notif ication can be
set to a ring tone, a prompt, or no
notif ication. The def ault setting is
aprompt.
Press and release the Talk button.
Af ter the beep, say ‘‘System setup.’’
HFL responds ‘‘System setup
options are security, change
passcode, call notif ication, auto
transf er, and clear. Press the Talk
button and say a command.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Security.’’
HFL responds ‘‘Security is
disabled. Would you like to enable
security? Press the Talk button
and say Yes or No.’’Press and release the Talk button.
Af ter the beep, say ‘‘Yes.’’
HFL responds ‘‘What is the f our-
digit number you would like to set
as your security passcode? Press
the Talk button and say the
number.’’
If you say ‘‘No,’’ HFL returns to
idle.
Press and release the Talk button.
Af ter the beep, say the f our-digit
passcode you want to use. For
example,say‘‘1,2,3,4.’’
HFLresponds‘‘1,2,3,4.Isthis
correct? Press the Talk button and
say Yes or No.’’
You can also select a ‘‘System
Clear’’ command to reset HFL
(see page ).
You can change the security
passcode. 3.
1. 2. 4.
244
To set a security passcode, do this:
Bluet oot hHandsFreeL ink
Setting Up the System
Setting a security passcode Selecting the incoming
notif ication
Changing a security passcode
Features
223
——y
y
(#yy