10. If necessary, add a50/50 mixtureof engine coolant and distilled
water to the engine coolant reservoir until the coolant level is at the
“cold fill range” as listed on the reservoir.
After any coolant has been added, check the coolant concentration (refer
toChecking engine coolantin theOwner’s Guide).If the
concentration is not 50/50 (protection to –34°F/–36°C), drain some
coolant and adjust the concentration. It may take several drains and
additions to obtain a 50/50 coolant concentration.
Whenever coolant has been added, the coolant level in the coolant
reservoir should be checked the next few times you drive the vehicle. If
necessary, add enough 50/50 concentration of engine coolant and
distilled water to bring the liquid level to the proper level.
If you have to add more than 1.0 quart (1.0 liter) of engine coolant per
month, have your dealer check the engine cooling system. Your cooling
system may have a leak. Operating an engine with a low level of coolant
can result in engine overheating and possible engine damage.
OCTANE RECOMMENDATIONS
Your vehicle is designed to use
“Premium” unleaded gasoline with
an (R+M)/2 octane rating of 91 or
higher for optimum performance.
The use of gasolines with lower
octane ratings may degrade performance. We do not recommend the use
of gasolines labeled as “Premium” in high altitude areas that are sold
with octane ratings of less than 91.
If your engine knocks under most driving conditions while you are using
fuel with the recommended octane rating, see your authorized dealer to
prevent any engine damage.
AIR FILTER
Refer toscheduled maintenance informationfor the appropriate
intervals for changing the air filter element.
When changing the air filter element, use only the Motorcraft air filter
element listed. Refer toMotorcraft part numbersin this chapter.
WARNING:To reduce the risk of vehicle damage and/or
personal burn injuries do not start your engine with the air
cleaner removed and do not remove it while the engine is running.
91(R+M)/2 METHOD
2009 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
26
Changing the air filter element
1. Release the clamps that secure
the air filter housing cover.
2. Carefully separate the two halves
of the air filter housing.
3. Remove the air filter element
from the air filter housing.
4. Wipe the air filter housing and
cover clean to remove any dirt or
debris and to ensure good sealing.
5. Install a new air filter element. Be
careful not to crimp the filter
element edges between the air filter
housing and cover. This could cause
filter damage and allow unfiltered
air to enter the engine if not
properly seated.
6. Replace the air filter housing
cover and secure the clamps.
MOTORCRAFT PART NUMBERS
Component 5.4L DOHC Supercharged V8
engine
Air filter element FA-1807
Fuel filter FG-1083
Battery BXT-40-R
Oil filter FL-820S
PCV valve EV-270
Spark plugs* AGSF-22FM1
* Refer to Vehicle Emissions Control Information (VECI) decal for spark
plug gap information.
2009 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
27
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
Item CapacityFord part name
or equivalentFord part
number / Ford
Specification
Brake fluidBetween MIN
and MAX
lines on
reservoirMotorcraft High
Performance DOT
3 Motor Vehicle
Brake FluidPM-1-C /
WSS-M6C62-A or
WSS-M6C65-A1
Engine oil
(includes filter
change)6.5 quarts
(6.1L)Motorcraft 5W-50
Full Synthetic
Motor OilX0-5W50-QGT /
WSS-M2C931-B
Engine coolant
121.1 quarts
(20.0L)Motorcraft
Premium Gold
Engine Coolant
with bittering
agent
(yellow-colored)VC-7-B /
WSS-M97B51-A1
Intercooler
coolant
1
3.96 quarts
(3.75L)
(See your
authorized
dealer for
service)Motorcraft
Premium Gold
Engine Coolant
with bittering
agent
(yellow-colored)VC-7-B /
WSS-M97B51-A1
Power steering
fluidBetween MIN
and MAX
lines on
reservoirMotorcraft
MERCONVATFXT-5-QM /
MERCONV
Rear axle
lubricant
24.25 pints
(2.0L)Motorcraft SAE
75W-140 High
Performance
Synthetic Rear
Axle LubricantXY-75W140-QL /
WSL-M2C192–A
Fuel tank15.7 gallons
(59.4L)——
2009 05+ Mustang(197)
Supplement
USA(fus)
Maintenance and Specifications
28