2009 FIAT PUNTO EVO boot

Repair and refit the standard wheel as
soon as possible. Do not apply grease to
the bolt threads before assembly: they might spon-
taneously unscrew.
WARNING
The jack may be used to replace wheels
only on the car which it equips or other
cars of the same model. Never use the jack for
other purposes, such as lifting other models. Nev-
er use the jack to carry out repairs under the car.
Incorrect positioning of the jack may cause the
car to fall. Do not use the jack for loads higher
than the one shown on its label.
WARNING
If the hub cap is not fitted correctly, it may
come off when the car is travelling. Nev-
er tamper with the inflation valve. Never intro-
duce tools of any kind between the rim and the
tyre. Check tyre and spare wheel pressures regu-
larly, referring to the values shown in the “Tech-
nical specifications” section.
WARNING
Important notes:
❒the jack weight is 1.76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired. If it breaks, it must be re-
placed with the same type;
❒no tool other than its cranking device may be fitted on
the jack.
To change a tyre, proceed as follows:
❒stop the car where it is not a danger to other road users
and you can replace the wheel safely. The ground should
be flat and solid;
❒turn the engine off and engage the handbrake;
❒engage first gear or reverse;
❒wear the reflective safety jacket (compulsory by law in
certain countries) before getting out of the car;
❒open the boot and lift the carpet or remove the cargo
box (for versions/markets where provided);
❒ unscrew the locking device A-fig. 151;
❒take out the tool container C-fig. 151 and put it along-
side the wheel to be changed;
❒take out the spare wheel B-fig. 151;
❒loosen the bolts of the wheel to be replaced by about
one turn with the wrench provided E-fig. 152; if you
have alloy wheels, rock the car to make it easier to sep-
arate the rim from the wheel hub;
177
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 177

REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise the
car and remove the spare wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces between standard wheel
and hub are clean so that the fastening bolts will not
come loose;
❒fit the standard wheel by inserting the first bolt two
threads into the hole closest to the inflation valve;
❒fit the hub cap by aligning the crescent hole with the
bolt you have fitted, then insert the other 3 bolts;
❒using the wrench provided, tighten the fastening bolts;
❒lower the car and remove the jack;
❒using the wrench provided, fully tighten the bolts in
the sequence shown previously.Versions with alloy rims
Proceed as follows:
❒place the wheel onto the hub and tighten the bolts us-
ing the wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully tighten the bolts in
the sequence shown previously.
After tyre replacement
❒stow the spare wheel in the space provided in the boot;
❒ put the jack back in its container partially open by forc-
ing it slightly against the container walls to prevent it
from rattling around when travelling;
❒put the tools back into their places in the container;
❒stow the container, complete with tools, inside the
spare wheel;
❒tighten the tool container locking device;
❒refit the boot carpet or the cargo box (for versions/
markets where provided).
180
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 180

F0U0139mfig. 156
QUICK TYRE REPAIR KIT -
FIX & GO automatic
The Fix & Go automatic quick tyre repair kit is located in
the boot.
The kit fig. 156 includes:
❒a canister A, containing sealant, which is fitted with:
– filler tube B;
– an adhesive label C with the message “max. 80 km/h”
to be placed where the driver can easily see it (on
the dashboard) after repairing the tyre;
❒instruction brochure (see fig. 157), to be used for
prompt and proper use of the quick repair kit and then
presented to the personnel charged with handling the
treated tyre;
❒compressor D-fig. 156 including gauge and connections;
❒a pair of protective gloves located in the side part of the
compressor;
❒ adapters for inflating different elements.
You can also find the screwdriver and tow hitch in the
quick repair kit container (stored in the boot under the
carpet).
F0U0140mfig. 157
Hand over the instruction booklet to the
personnel charged with treating the tyre
repaired with the kit.
WARNING
181
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 181

H4
H4
W5W
H11
PY21W
WY5W
P21W
LED
P21W
W2.3W
W16W
W16W
W5W
C10W
C10W
C10W
W5W
C5W D
D
A
–
B
A
B
–
B
B
–
–
A
C
C
C
A
C55 W
60 W
5 W
55 W
21 W
5 W
21 W
–
21 W
2.3 W
16 W
16 W
5 W
10 W
10 W
10 W
5 W
5 W
188
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Bulbs Figure ref. Type Power
Main beams
Dipped beams
Front sidelights
Front fog lights (where provided)
Front direction indicators
Side direction indicators
Rear direction indicators
Taillights
Brake lights
Third brake light
Reverse lights
Rear fog lights
Number plate lights
Front ceiling light with movable lens
Front ceiling light with spot lights
Rear ceiling light
Boot light
Courtesy light
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 188

194
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒refit the bulb holder;
❒reconnect the electric connector, correctly realign the
unit with the car body and then tighten the fastening
screws A.
IMPORTANT To replace the LED taillights you must con-
tact a Fiat Dealership.
REAR FOG LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the rear fog
lights A replaced.
REVERSE LIGHTS fig. 176
Contact a Fiat Dealership to have bulbs for the reverse
lights B replaced.
F0U0157mfig. 176F0U0281mfig. 177
THIRD BRAKE LIGHT fig. 177
To change the bulb proceed as follows:
❒open the boot;
❒remove the rubber caps;
❒press in the catches and remove the lens unit
C-fig. 177;
❒disconnect the electric connector;
❒press in the tabs D-fig. 177 and remove the bulb holder;
❒remove the snap-fitted bulb and replace it.
NUMBER PLATE LIGHTS
To change the bulb proceed as follows:
❒manipulate the point shown by the arrow and remove
the lens unit A-fig. 178;
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 194

197
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0167mfig. 184
BOOT LIGHT fig. 185
To change the bulb, proceed as follows:
❒open the boot;
❒remove the light A-fig. 185 by levering on the point
shown by the arrow.
❒open the protective cover B and replace the snap-fitted
bulb;
❒re-close the protective cover B over the lens;
❒refit the light A by inserting it in its correct position first-
ly on one side and then on the other until it clicks into
place.
F0U0168mfig. 185
PUDDLE LIGHTS fig. 186
(for versions/markets where provided)
To change the bulb, proceed as follows:
❒remove the light by pressing clip A-fig. 186 with a screw-
driver;
❒press the sides of bulb shield B-fig. 187 on the two fas-
tening pins and turn it;
❒replace the snap-fitted bulb C;
❒reposition the bulb shield by fitting the two fastening
pins;
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 197

F0U0172mfig. 189
F0U0173mfig. 190200
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
FUSE LOCATION
The fuses are grouped in three control units: on the dash-
board, in the engine compartment and in the left-hand side
of the boot.
Dashboard fuse box fig. 190
To access the dashboard fuse box, loosen the screws
A-fig. 189 and remove the cover.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 200

F0U0176mfig.193
F0U0177mfig. 194
Boot fuse box fig. 194
To gain access to the fuse box located on the left side of
the boot, open the relevant inspection lid (as shown in
fig. 193).
202
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 202