2009 FIAT PUNTO EVO technical specifications

195
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0160mfig. 179
F0U0159mfig. 178
❒change the bulb fig.179 by releasing it from the side
contacts and making sure the new bulb is correctly fas-
tened between these contacts;
❒refit the snap-fitted lens unit.
F0U0163mfig. 180
CHANGING AN INTERIOR BULB
For the type of bulb and relevant power rating, see
“Changing a bulb”.
FRONT CEILING LIGHT
Proceed as follows to replace the bulbs:
❒manipulate the points shown by the arrows and remove
light A-fig. 180;
❒ open the protective flap B-fig. 181;
❒replace bulbs C-fig. 181 by releasing them from the side
contacts and making sure that new bulbs are correctly
clamped between these contacts;
❒close the flap B-fig. 181 and fasten the courtesy light
A-fig. 180 in its housing, making sure it is locked in cor-
rectly.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 195

F0U0164mfig. 181
REAR CEILING LIGHT
(for versions/markets where provided)
Proceed as follows to replace the bulbs:
❒manipulate the points shown by the arrows and remove
light D-fig. 182;
❒open the protective flap E-fig. 183;
❒replace bulb F-fig. 183 by releasing it from the side con-
tacts and making sure that the new bulb is correctly
clamped between these contacts;
❒re-close the protective flap E-fig. 183 and fit light D-fig.
182 into its housing, making sure it locks into place
properly.
196
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0166mfig. 183
F0U0165mfig. 182
COURTESY LIGHT fig. 184
To change the bulb, proceed as follows:
❒remove the light A-fig. 184 by levering on the points
shown by the arrow.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 196

197
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0167mfig. 184
BOOT LIGHT fig. 185
To change the bulb, proceed as follows:
❒open the boot;
❒remove the light A-fig. 185 by levering on the point
shown by the arrow.
❒open the protective cover B and replace the snap-fitted
bulb;
❒re-close the protective cover B over the lens;
❒refit the light A by inserting it in its correct position first-
ly on one side and then on the other until it clicks into
place.
F0U0168mfig. 185
PUDDLE LIGHTS fig. 186
(for versions/markets where provided)
To change the bulb, proceed as follows:
❒remove the light by pressing clip A-fig. 186 with a screw-
driver;
❒press the sides of bulb shield B-fig. 187 on the two fas-
tening pins and turn it;
❒replace the snap-fitted bulb C;
❒reposition the bulb shield by fitting the two fastening
pins;
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 197

F0U0170fig. 187
F0U0169mfig. 186
198
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒refit the light by first inserting side D-fig. 186 and then
pressing the other side until you hear the clip lock in-
to place.
F0U0171mfig. 188
CHANGING A FUSE
GENERAL INFORMATION
Fuses protect the electrical system: they cut in (i.e. they
blow) in the event of a fault or improper action on the sys-
tem.
Check the state of the corresponding fuse when a device
does not work: the filament A-fig. 188 must be intact. If it
is not, replace the blown fuse with a new one of the same
amperage (same colour).
B undamaged fuse
C fuse with damaged filament.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 198

199
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Never replace a blown fuse with metal
wires or other materials.
Should the fuse blow again, contact a Fi-
at Dealership.
WARNING
Never replace a fuse with one that has
a higher amperage: FIRE HAZARD.
WARNING
If a general protection fuse (MEGA-FUSE,
MIDI-FUSE, MAXI-FUSE) is activated,
contact a Fiat Dealership.
WARNING
Remove the key from the ignition and
switch off or disable all devices before re-
placing a fuse.
WARNING
If a general protection fuse for safety sys-
tems (air bag system, braking system),
power unit systems (engine system, transmission
system) or steering system is triggered, contact a
Fiat Dealership.
WARNING
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 199

F0U0172mfig. 189
F0U0173mfig. 190200
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
FUSE LOCATION
The fuses are grouped in three control units: on the dash-
board, in the engine compartment and in the left-hand side
of the boot.
Dashboard fuse box fig. 190
To access the dashboard fuse box, loosen the screws
A-fig. 189 and remove the cover.
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 200

201
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0174mfig. 191
Engine compartment fuse box fig. 192
To access the fuse box located next to the battery, re-
move the protective cover fig. 191 by manipulating the
points indicated by the arrow.
F0U0175mfig. 192
175-210 PUNTO FL EN 4ed 2-02-2010 14:05 Pagina 201

F0U0176mfig.193
F0U0177mfig. 194
Boot fuse box fig. 194
To gain access to the fuse box located on the left side of
the boot, open the relevant inspection lid (as shown in
fig. 193).
202
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 3ed 9-12-2009 13:42 Pagina 202