2009 FIAT PANDA Speed

27KNOW YOUR
VEHICLESAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Note The “Scheduled servicing plan” ensures car servic-
ing every 20,000 km (or 12,000 miles). This is automati-
cally displayed when the ignition key is in the MAR posi-
tion, from 2,000 km (or the equivalent in miles) before the
service and reappears every 200 km (or the equivalent
in miles). Below 200 km servicing indications are more fre-
quent. The displaying will be in kilometres or miles de-
pending on the measurement unit settings. When the next
scheduled servicing is approaching (“coupon”), the mes-
sage “Service” will appear on the display followed by
the number of kilometres or miles left when the key is
turned to MAR. Contact a Fiat Dealership to carry out any
service operation provided by the “Scheduled servicing
plan” and to reset the display.
Exit Menu
This is the last function that closes the cycle of settings
listed in the menu screen.
Briefly press the button MODE to go back to the standard
screen without storing the settings.
Press the button
–to return to the first menu option
(Speed Lim.). Adjust the button volume (Button Vol.)
This function is used to set the volume (8 levels) of the
beep accompanying the activation of the buttons MODE,
+ and –.
To set the desired volume, proceed as follows:
– briefly press the button MODE: the previously set
volume “level” will flash on the display;
– press the button + or – for setting;
– briefly press the button MODE to go back to the menu
screen or press the button for a prolonged time to go back
to the standard screen without storing the settings.
Scheduled Servicing (Service)
By this function you can display information about the
mileage intervals for car servicing.
To consult this display, proceed as follows:
– briefly press the button MODE: the display shows ser-
vice requirements in km or mi according to the previous
setting (see paragraph “Measurement units”);
– briefly press the button MODE to go back to the menu
screen or press the button for a prolonged time to go back
to the standard screen.
001-030 PANDA EN 7-10-2009 13:40 Pagina 27

28
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
– Average consumption B (for versions/markets where
provided)
– Average speed B
– Trip time B (driving time).
NOTE “Trip B” function can be excluded (see paragraph
“Trip B on”). “‘Range to empty” cannot be reset.
Values displayed
Range (for versions/markets where provided)
This value shows the distance that the car can still cover
before needing fuel, assuming that driving conditions are
kept unvaried. The display will show the reading “----”
when the following events take place:
– range value lower than 50 km (or 30 mi)
– car parked with engine running for long.
Trip distance
This value shows the distance covered from the start of
the new mission.Average consumption (for versions/markets where provided)This value shows the average consumption from the start
of the new mission.Instant consumption (for versions/markets where provided)This indicates instant fuel consumption and it is constant-
ly updated. The display will show “----” if the car is parked
with the engine running.
TRIP COMPUTER (for versions/markets, where provided)
General features
The “Trip computer” is provided on cars fitted with mul-
tifunction display or reconfigurable multifunction display.
With ignition key at MAR, the “Trip computer” displays
information about the operating status of the car. This
function comprises the “General trip” concerning the
“complete mission” of the car (journey) and “Trip B”, (on-
ly available on reconfigurable multifunction display), con-
cerning the partial mission of the car; this function is in-
cluded in the general trip information (as shown in fig. 30).
Both functions can be reset (reset means start of a new
journey).
“General Trip” displays the figures relating to:
– Range to empty (for versions/markets, where provided)
– Trip distance
– Average consumption (for versions/markets where pro-
vided)
– Instant consumption (for versions/markets where pro-
vided)
– Average speed
– Trip time (driving time).
“Trip B”, available on the reconfigurable multifunction dis-
play only, shows only the figures relating to:
– Trip distance B
001-030 PANDA EN 7-10-2009 13:40 Pagina 28

29KNOW YOUR
VEHICLESAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
New mission
A new mission starts after:
– “manual” resetting by the user, by pressing the relevant
button;
– “automatic” resetting, when the “Trip distance” reaches
3999.9 km or 9999.9 km (according to the type of display)
or when the “Trip time” reaches 99.59 (99 hours and 59
minutes);
– disconnection/reconnection of the battery.
IMPORTANT The reset operations performed after the
“General Trip” message displaying are used to also reset
the “Trip B”, which, on its turn, is used to reset the
values of the corresponding function. Average speed
This shows the car average speed as a function of the over-
all time elapsed since the start of the new mission.
Trip time
This value shows the time elapsed since the start of the
new mission.
IMPORTANT Lacking information, Trip Computer values
are displayed with “----”. When normal operating condi-
tion is reset, calculation of different units will restart reg-
ularly. All values displayed before the failure will not be
reset nor a new mission is started.
Button TRIP fig. 29
The button
TRIP
is located on the top of the right-hand
lever. With the ignition key turned to
MAR
, by this but-
ton the previously described parameters can be displayed
and reset to start a new mission:
– short pressing to display the different values;
– prolonged pressing to reset and then start a new
mission.
TRIP
F0Z0149m
fig. 29
001-030 PANDA EN 7-10-2009 13:40 Pagina 29

F0Z0022m
fig. 44
It is advisable to switch the internal air recirculation on while
standing in queues or in tunnels to prevent the introduc-
tion of polluted air. However, it is better not to use the
function for long periods, particularly if there are many peo-
ple on board, to prevent the windows from misting inside.
IMPORTANT The inside air recirculation system makes it
possible to reach the required heating or cooling condi-
tions faster. Do not use the air recirculation function on
rainy/cold days as it would considerably increase the pos-
sibility of the windows misting inside.
Air distribution knob
D
¥
to convey air to the central and side vents;
μ
to send air to the feet and convey cooler air to
the dashboard vents, in intermediate temperature
conditions;
w
to heat with outside harsh temperature: close central
and side vents to convey as much air as possible to
the feet;
≤to warm the feet and, at the same time, demist the
windscreen;
-
for quick windscreen demisting. CONTROLS fig. 44
Air temperature knob A (mixing hot/cold air)
Red section = hot air
Blue section = cold air
Fan activation/adjustment knob B
0 = fan off
1-2-3 = fan speed
-
= maximum fan speed
Air recirculation on/off knob
C
U
= outside air intake
T
= inside air recirculation
38
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
031-064 PANDA EN 7-10-2009 13:43 Pagina 38

39KNOW YOUR
VEHICLESAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Then use the controls to keep the required comfort con-
ditions and turn the knob C to
U
.
IMPORTANT With cold engine, you have to wait for
a few minutes to let the system fluid reach the operating
temperature.
FRONT WINDOW FAST DEMISTING
AND/OR DEFROSTING
Proceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob C to
U
;
❒
turn the knob D to
-
;
❒
turn the knob B to
-
(maximum fan speed).
After demisting/defrosting, operate the controls to keep
the required comfort conditions. PASSENGER COMPARTMENT VENTILATION
To ventilate the passenger compartment properly, pro-
ceed as follows:
❒
fully open the central and side air vents;
❒
turn the knob A to blue sector;
❒
turn the knob C to
U
;
❒
turn the knob D to
¥;
❒
turn the knob B to the required speed.
PASSENGER COMPARTMENT HEATING
Proceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob D to the required symbol;
❒
turn the knob B to the required speed.
FAST PASSENGER COMPARTMENT HEATING
For the fast heating of the passenger compartment, pro-
ceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob C to
T
;
❒
turn the knob D to
-
;
❒
turn the knob B to
-
(maximum fan speed).
031-064 PANDA EN 7-10-2009 13:43 Pagina 39

F0Z0143m
fig. 45
REAR WINDOW DEMISTING/DEFROSTING
fig. 45
Press the button A to activate this function; when this
function is on the instrument panel warning light
(
will
turn on.
This function is timed and it will turn off automatically
after about 20 minutes. Press the button
(
again to switch
the function off.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid dam-
age that might cause it to stop working properly. Preventive window demisting procedure
In the event of considerable external moisture and/or rain
and/or large differences in temperature inside and outside
the passenger compartment, perform the following pre-
ventive window demisting procedure:
❒
turn the knob A to the red sector;
❒
make sure the knob C is turned to
U
;
❒
turn the knob D to
-
with the possibility of passing to
position ≤if the windows do not mist up;
❒
turn the knob B to 2
ndspeed.
40
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
031-064 PANDA EN 7-10-2009 13:43 Pagina 40

41KNOW YOUR
VEHICLESAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Air recirculation on/off knob CU
= outside air intake
T
= inside air recirculation
It is advisable to switch the internal air recirculation on while
standing in queues or in tunnels to prevent the introduc-
tion of polluted air. However, it is better not to use the
function for long periods, particularly if there are many peo-
ple on board, to prevent the windows from misting inside.
IMPORTANT The inside air recirculation system makes it
possible to reach the required heating or cooling condi-
tions faster. Do not use the air recirculation function on
rainy/cold days as it would considerably increase the pos-
sibility of the windows misting inside.
Air distribution knob D
¥
air flow from central vents and side vents;
μ
to warm the feet and keep the face cool (“bilevel”
function);
w
to speed up passenger compartment warming;
≤to warm the passenger compartment and at the same
time demist the windscreen;
-
to demist and defrost the windscreen and front side
windows.
MANUAL CLIMATE CONTROL
SYSTEM(for versions/markets where provided)
CONTROLS fig. 46
Air temperature knob
A(mixing hot/cold air)
Red section = hot air
Blue section = cold air
Fan activation and climate control system on/off
knob B
0 = fan off
1-2-3 = fan speed
-
= maximum fan speed
Press the knob to turn the climate control system on, the
LED on the knob will turn on. Press it again to turn it off,
the LED will turn off.
F0Z0600m
fig. 46
031-064 PANDA EN 7-10-2009 13:43 Pagina 41

Then use the controls to keep the required comfort con-
ditions and turn the knob
Cto
U
.
IMPORTANT With cold engine, you have to wait for
a few minutes to let the system fluid reach the operating
temperature.
WINDSCREEN AND FRONT SIDE WINDOW
FAST DEMISTING/DEFROSTING
(MAX-DEF function)
Proceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob C to
U
;
❒
turn the knob D to
-
;
❒
turn the knob B to
-
(maximum fan speed).
After demisting/defrosting, operate the controls to keep
the required comfort conditions.
IMPORTANT The climate control system is very useful to
speed up demisting since it dehumidifies the air. Adjust the
controls as described above and press knob B to switch
the climate control system on: the LED on the knob will
light up. PASSENGER COMPARTMENT VENTILATION
To ventilate the passenger compartment properly, pro-
ceed as follows:
❒
fully open the central and side air vents;
❒
turn the knob A to blue sector;
❒
turn the knob C to
U
;
❒
turn the knob D to
¥;
❒
turn the knob B to the required speed.
PASSENGER COMPARTMENT HEATING
Proceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob D to the required symbol;
❒
turn the knob B to the required speed.
FAST PASSENGER COMPARTMENT HEATING
For the fast heating of the passenger compartment, pro-
ceed as follows:
❒
turn the knob A to the red sector;
❒
turn the knob C to
T
;
❒
turn the knob D to
-
;
❒
turn the knob B to
-
(maximum fan speed).
42
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
031-064 PANDA EN 7-10-2009 13:43 Pagina 42