2009 FIAT BRAVO ESP

141
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
GENERAL WARNINGS ..................................................... 142
LOW BRAKE FLUID............................................................ 142
HANDBRAKE ON................................................................ 142
BRAKE PAD WEAR ............................................................ 142
AIR BAG FAILURE ................................................................ 143
FRONT PASSENGER AIR BAG/
SIDE BAGS DEACTIVATED....................................................... 143
SEAT BELTS NOT FASTENED .......................................... 144
LOW BATTERY CHARGE ................................................. 144
LOW ENGINE OIL PRESSURE.......................................... 144
EXHAUSTED OIL ................................................................ 144
“DUALDRIVE” ELECTRIC POWER
STEERING FAILURE.............................................................. 145
“DUALDRIVE” ELECTRIC POWER STEERING
ACTIVATION ....................................................................... 145
ENGINE COOLANT HIGH TEMPERATURE ................ 146
INCOMPLETE DOOR LOCKING .................................... 146
BOOT OPEN......................................................................... 146
BONNET OPEN ................................................................... 146
GENERIC FAILURE INDICATION ................................. 147
DIESEL PARTICULATE FILTER CLOGGED ................. 147
FUEL RESERVE ....................................................................... 148
EOBD/INJECTION SYSTEM FAILURE ............................. 149
ESP SYSTEM .......................................................................... 149
HILL HOLDER FAILURE .................................................... 149
GLOW PLUG WARMING ................................................ 149GLOW PLUG WARMING FAILURE............................... 149
WATER IN DIESEL FUEL FILTER..................................... 149
ABS SYSTEM FAILURE......................................................... 150
EBD SYSTEM FAILURE ........................................................ 150
CAR PROTECTION SYSTEM
FAILURE FIAT CODE.......................................................... 150
ALARM FAILURE.................................................................. 150
THEFT ATTEMPT................................................................. 150
T.P.M.S. SYSTEM FAILURE ................................................. 151
LOW TYRE PRESSURE ...................................................... 151
CHECK TYRE PRESSURE .................................................. 151
TYRE PRESSURE UNSUITABLE FOR SPEED ................. 151
EXTERNAL LIGHTS FAILURE........................................... 153
BRAKE LIGHTS FAILURE................................................... 153
REAR FOGLIGHTS............................................................... 153
FRONT FOG LIGHTS.......................................................... 153
LEFT-HAND DIRECTION INDICATOR ........................ 153
RIGHT-HAND DIRECTION INDICATOR .................... 153
SIDE/TAILLIGHTS AND LOW BEAMS ........................... 154
FOLLOW ME HOME ........................................................... 154
MAIN BEAMS......................................................................... 154
CRUISE CONTROL ............................................................ 154
POSSIBLE PRESENCE OF ICE ON THE ROAD ........... 154
LIMITED RANGE ................................................................. 154
ASR SYSTEM ......................................................................... 154
SPEED LIMIT EXCEEDED .................................................. 154
SPORT FUNCTION ACTIVATION................................. 154
W W
A A
R R
N N
I I
N N
G G
L L
I I
G G
H H
T T
S S
A A
N N
D D
M M
E E
S S
S S
A A
G G
E E
S S
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 141

HILL HOLDER FAILURE
(amber)
The symbol
*will turn on
when the Hill Holder system is
faulty. Contact Fiat Dealership
as soon as possible.
On certain versions warning
light
áturns on as an alternative.
The display will show the dedicated mes-
sage.
149
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
ESP SYSTEM
(amber)
Turning the ignition key to
MARthe warning light turns on,
but it should go off after few seconds.
If the warning light does not turn off or
stays on when travelling together with the
button led ASR, contact Fiat Dealership.
On certain versions the dedicated mes-
sage is displayed.
Warning light flashing when driving indi-
cates that the ESP system is active.
á
á
GLOW PLUG
WARMING
(Multijet versions)
(amber)
GLOW PLUG
WARMING FAILURE
(Multijet versions)
(amber)
Glow plug warming
Turning the ignition key to MARthe
warning light turns on and it will go off
when glow plugs reach the preset tem-
perature. Start the engine immediately af-
ter warning light turning off.
IMPORTANT With high ambient tem-
perature, warning light stays on for very
short time.
Glow plug warming failure
The warning light turns on when there is
a failure in the glow plug warming system.
Contact Fiat Dealership as soon as possi-
ble.
The display will show the dedicated mes-
sage.
m
*
WATER IN DIESEL
FUEL FILTER
(Multijet versions)
(amber)
Turning the ignition key to MARthe
warning light turns on, but it should go off
after few seconds.
The warning light turns on when there is
water in the diesel fuel filter.
The display will show the dedicated mes-
sage.
c
The presence of water in the
fuel circuit may cause serious
damage to the entire injec-
tion system and cause irreg-
ular engine operation. If the warning
light
cturns on (together with the
message on the display), contact Fi-
at Dealership as soon as possible to
have the system relieved. If the above
indications come on immediately af-
ter refuelling, water has probably
been poured into the tank: turn the
engine off immediately and contact
Fiat Dealership.
141-154 BRAVO GB:141-154 BRAVO GB 11-11-2009 10:55 Pagina 149

157
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
IF A TYRE IS
PUNCTURED
The car is provided with the “Quick tyre
repair kit Fix&Go automatic“: see the rel-
evant instructions for use in next chapter.
GENERAL INSTRUCTIONS
As an alternative to the Fix&Go kit, the
car can be provided (upon request) with
space-saver spare wheel or standard size
spare wheel; wheel changing and correct
use of the jack and space-saver spare
wheel call for some precautions as listed
below.
Alert other drivers that the
car is stationary in compli-
ance with local regulations: hazard
warning lights, warning triangle, etc.
Any passengers on board should leave
the car, especially if it is heavily laden.
Passengers should stay away from on-
coming traffic while the wheel is be-
ing changed. If parked on a slope or
rough surface, chock the wheels with
wedges or other suitable devices to
prevent the car from rolling.
WARNING
The space-saver spare wheel
(for versions/markets, where
provided) is specific to your car, do
not use it on other models, or use the
spare wheel of other models on your
car. The space-saver spare wheel
shall only be used in an emergency. It
shall only be used for the distance
necessary to reach a service point and
the car speed shall not exceed 80
Km/h. The spare wheel has an orange
sticker that summarises the main cau-
tions for use and limitations. The
sticker should never be removed or
covered. Never fit a wheel cap on a
space-saver spare wheel. The sticker
gives the following information in four
languages: caution! For temporary
use only! 80 km/h max! Replace by
normal wheel as soon as possible. Do
not cover this label.
WARNING
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 157

161
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒install the space-saver spare wheel
matching the holes S-fig. 7with the
corresponding pins T;
❒using the wrench provided, fully tight-
en the four fastening bolts;
❒work the jack handle R-fig.6to lower
the car and remove the jack;
❒using the wrench provided, tighten up
the wheel bolts in a criss-cross fashion
following the sequence shown in fig. 8.REFITTING THE STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
For versions with steel rim
Proceed as follows:
❒ Make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will not
come loose;
❒Fit the normal wheel matching the
holes S-fig. 7with the corresponding
pins T;
❒Using the wrench provided, tighten the
fastening bolts;
❒ Lower the car and remove the jack;
❒Using the wrench provided, fully tight-
en the bolts in the sequence shown in
fig. 8;
❒Place the cap near the wheel so that the
inflation valve can come through the
slot provided on the cap;
❒Press the circumference of the cap,
starting from the parts nearest the in-
flation valve until it is inserted com-
pletely.
IMPORTANT Incorrect fitting may cause
the wheel cap to come off when the car is
travelling.
fig. 7F0Q0396mfig. 8F0Q0397m
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 161

165
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒make sure the compressor switch
E-fig. 15is set to 0(off), start the en-
gine and fit plug D-fig. 14into the cig-
ar lighter outlet and then turn on the
compressor by setting switch E-fig. 15
to I(on). Inflate the tyre to the pres-
sure specified in paragraph “Cold tyre
inflation pressure” in section “Techni-
cal specifications”. Check tyre pressure
on gauge F-fig. 15with compressor off
to obtain precise reading; ❒If after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
❒If reaching the tyre pressure specified
in paragraph “Cold tyre inflation pres-
sure” in section “Technical specifica-
tions”, start driving immediately;
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
fig. 14F0Q0515mfig. 15F0Q0516mfig. 15aF0Q0017m
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 165

167
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
WHEN NEEDING
TO CHANGE A BULB
GENERAL INSTRUCTIONS
❒ When a light is not working, check that
the corresponding fuse is intact before
changing a bulb. For the location of fus-
es, refer to the paragraph “If a fuse
blows” in this section;
❒ Before changing a bulb check the con-
tacts for oxidation;
❒ Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒ Always check the height of the head-
light beam after changing a bulb.Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent bulb
is touched with the fingers, its
lighting intensity is reduced and life of
the bulb may be compromised. If
touched accidentally, rub the bulb with
a cloth moistened with alcohol and al-
low to dry.
Modifications or repairs to
the electrical system (elec-
tronic control units) carried out in-
correctly and without bearing the fea-
tures of the system in mind can cause
malfunctions with the risk of fire.
WARNING
Due to high voltage, the bulb
of (Bi-Xenon) gas-discharge
headlights must only be replaced by
experts: danger of death! Contact
Fiat Dealership.
WARNING
IMPORTANT When the weather is cold
or damp or after hard rain or after wash-
ing, the area of headlamps or rear lights,
may steam up and/or form drops of con-
densation on the inside. This is a natural
phenomenon due to the difference in tem-
perature and humidity between the inside
and the outside of the glass which does
not indicate a fault and does not compro-
mise the normal operation of lighting de-
vices. The mist disappears quickly turn-
ing the lights on, starting from the centre
of the diffuser, extending progressively to-
wards the edges.
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 167

190
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
The front and rear tow hooks
must only be used for emer-
gency situations on the road.
The vehicle may be towed for
short distances when a dedicated de-
vice is used in compliance with the
Highway Code (rigid bar), in order to
move the vehicle on the road in prepa-
ration for towing by a tow truck Tow
hooks MUST NOT be used to tow ve-
hicles off the road or where there are
obstacles and/or for towing operations
using cables or other non-rigid devices.
Respecting the above conditions, tow-
ing must only take place with two ve-
hicles (one towing, the other towed)
travelling as far as possible in alignment
along the same centreline.
155-190 BRAVO GB.qxd 11-11-2009 10:56 Pagina 190

194
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Thousands of km
Check exhaust emissions (petrol versions)
Check emissions/fumes (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Check operation of engine control systems
(by means of test interface)
Replace accessory drive belt/s
Replace toothed timing belt (petrol versions) (*)
Replace toothed timing belt (1.9 Multijet 8Vversions) (*)
Replace toothed timing belt (1.9 Multijet 16Vversions) (*)
Replace spark plugs (petrol versions) 1
Replace fuel filter (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace air filter cartridge (petrol versions)
Replace air filter cartridge (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace engine oil and oil filter (petrol versions)
(or every 24 months) 2
Change engine oil and oil filter (
1.9 Multijet 8V - 1.9 Multijet 16V
versionswithout DPF) (or every 24 months)
Change engine oil and oil filter
(1.9 Multijet 8V - 1.9 Multijet 16V versionswith DPF) (**) 2
Change brake fluidr (or every 24 months)
Change pollen filter (or every 15 months)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town use, long
periods idling) or at least every 5 years.
(**) The engine oil and oil filter should be changed depending on their actual condition, which is indicated by a warning light/message on the control panel or at
least every 2 years.
1For 1.4 T-JET versions, in order to ensure correct operation and avoid significant damages to the engine, it is mandatory:
- to use spark plugs specifically certified for the T-JET engine only, of the same type and brand (see paragraph “Engine”);
- to replace the plugs as often as required by the Programmed Maintenance Plan;
- we recommend to refer to the Fiat Dealership.
2If the car is used mainly on urban routes or if the yearly kilometres travelled are less than 10,000 km, the engine oil and filter must be changed every 12 months.
30 60 90 120 150 180
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●
●
●
●
●● ● ●● ●
●●●
●●●
●●●
●● ● ●● ●
●● ● ●● ●
●●●
●●●
●●●●●●
191-212 BRAVO GB:191-212 BRAVO GB 11-11-2009 10:56 Pagina 194