2009 DODGE JOURNEY dead battery

Fob With Integrated Key
The Fob with Integrated Key operates the ignition switch.
It also contains the Remote Keyless Entry (RKE) trans-
mitter and a valet key, which stores in the rear of the Fob.
The valet key allows for entry into the vehicle should the
battery in the vehicle or the Fob go dead. You can keep
the valet key with you when valet parking.
To remove the valet key from the Fob, slide the mechani-
cal latch at the top of the Fob sideways with your thumb
and then pull the key out of the Fob with your other
hand.NOTE:
•You can insert the double-sided valet key into the lock
cylinder with either side up.
•Only the drivers door is equipped with a lock cylinder.
Valet Key Removal
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
2

NOTE:You MUST press and hold the brake pedal down
while shifting out of PARK.
WARNING!
• It is dangerous to move the shift lever out of PARK or
NEUTRAL if the engine speed is higher than idle speed.
If your foot is not firmly on the brake pedal, the vehicle
could accelerate quickly forward or in reverse. You could
lose control of the vehicle and hit someone or something.
Only shift into gear when the engine is idling normally
and when your right foot is firmly on the brake pedal.
• Unintended movement of a vehicle could injure those in
and near the vehicle. As with all vehicles, you should
never exit a vehicle while the engine is running. Before
exiting a vehicle, you should always shift the vehicle into
PARK, remove the key from the ignition, and apply the
parking brake. Once the key is removed from the igni-
tion, the shift lever is locked in the PARK position,
securing the vehicle against unwanted movement. Fur-
thermore, you should never leave unattended children
inside a vehicle.
Brake/Transaxle Interlock System
This vehicle is equipped with a Brake Transaxle Shift
Interlock System (BTSI) that holds the shift lever in the
PARK position when the ignition switch is in the LOCK
position. To move the shift lever out of the PARK
position, the ignition switch must be turned to the ON
position, and the brake pedal must be depressed.
BTSI Override
There is an override for the BTSI that allows you to move
the shift lever out of the PARK position if an electrical
system malfunction occurs (i.e., dead battery). To activate
the override system, perform the following steps:
1. Firmly apply the parking brake.
2. Insert the ignition key into the ignition switch and
rotate it to the ON position.
3. Remove the cubby bin liner located in the center
console behind the shift lever.
312 STARTING AND OPERATING

off the message. If the problem persists, the message will
appear the next time the vehicle is started.
A loose, improperly installed, or damaged fuel filler cap
may also turn on the MIL.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of this vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.For states that require an Inspection and Mainte-
nance (I/M), this check verifies the Malfunction
Indicator Light (MIL) is functioning and is not on
when the engine is running, and that the OBD II system
is ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if the vehicle was recently serviced, recently had a dead battery, or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, the vehicle may fail the test.
This vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if this vehicle’s OBD II system is ready, you must
do the following:
1. Insert the ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn the ignition key to the ON
position, you will see the MIL symbol come on as part of
a normal bulb check.
422 MAINTAINING YOUR VEHICLE