2009 DODGE JOURNEY homelink

To Arm the System
1. Remove the key from the ignition switch and exit the
vehicle.
2. Lock the doors and liftgate by pressing the power door
LOCK switch or the LOCK button on the Remote Keyless
Entry (RKE) transmitter.
NOTE:The system will not arm if you lock the doors
with the manual door LOCK plungers or the door LOCK
cylinder on the driver’s door.
3. Close all doors. The Vehicle Security Light in the
instrument cluster will flash rapidly for about 16 seconds
to signal that the system is arming. During this period,
opening any door or the liftgate will cancel the arming
process. If the system arms successfully, the Vehicle
Security Light will flash at a slower rate to indicate the
alarm is set. NOTE:
For added security, whenever the Security
Alarm is armed, the HomeLink/Garage Door Opener
(if equipped) is disabled as well.
To Disarm the System
Either press the UNLOCK button on the RKE transmitter
or insert a valid ignition key into the ignition lock
cylinder and turn the key to the ON position.
NOTE:
•Unlocking the doors with the manual door LOCK
plungers or the door LOCK cylinder on the driver’s
door will not disarm the system.
•When the system is armed, the interior power door
LOCK switches will not unlock the doors.
The Security Alarm System is designed to protect your
vehicle; however, you can create conditions where the
system will give you a false alarm. If the previously
described arming sequence has occurred, the system will
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
2

▫Flash To Pass ........................150
▫ Interior Lights .......................151
 Windshield Wipers And Washers ............153
▫ Intermittent Wiper System ...............155
▫ Mist Feature .........................155
▫ Headlights With Wipers (Available With Auto
Headlights Only) .....................156
▫ Windshield Washers ...................156
▫ Adding Washer Fluid ..................157
 Tilt/Telescoping Steering Column —
If Equipped ...........................157
 Electronic Speed Control — If Equipped ......159
▫ Electronic Speed Control Operation ........159
▫ To Activate ..........................159 ▫
To Set At A Desired Speed ...............160
▫ To Deactivate ........................160
▫ To Resume Speed .....................160
▫ To Vary The Speed Setting ...............161
▫ To Accelerate For Passing ...............161
 Overhead Console ......................162
▫ Courtesy/Reading Lights ................162
▫ Sunglasses Storage ....................163
▫ Interior Observation Mirror ..............163
▫ Power Sunroof Switch — If Equipped .......163
 Garage Door Opener — If Equipped .........163
▫ Programming HomeLink ...............165
▫ Gate Operator/Canadian Programming .....167
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
3

▫Using HomeLink .....................168
▫ Reprogramming A Single HomeLink
Button .............................168
▫ Security ............................169
▫ Troubleshooting Tips ...................169
▫ General Information ...................169
 Power Sunroof — If Equipped .............170
▫ Opening Sunroof - Manually .............171
▫ Opening Sunroof - Express ..............171
▫ Closing Sunroof - Manually ..............171
▫ Closing Sunroof - Express ...............172
▫ Pinch Protect Feature ...................172
▫ Pinch Protect Override .................172 ▫
Venting Sunroof - Express ...............172
▫ Sunshade Operation ...................173
▫ Wind Buffeting .......................173
▫ Sunroof Maintenance ...................173
▫ Ignition Off Operation ..................173
▫ Sunroof Fully Closed ...................174
 Electrical Power Outlets ..................174
▫ Electrical Outlet Use With Engine Off .......176
 Power Inverter — If Equipped .............176
 Cup And Bottle Holders ..................178
▫ Cupholders .........................178
▫ Bottle Holders .......................179
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sunglasses Storage
To access the storage compartment, press on the raised
bars on the compartment door in the center of the console
and release and the door will swing downward.
Interior Observation Mirror
The convex interior observation mirror provides the
driver and front seat passenger a wide field of view to
conveniently view passengers sitting in the rear passen-
ger seats. To use the interior observation mirror, first,
press on the raised bars on the compartment door and
release. The door will swing downward. Then, raise the
door until it is almost closed and release. The door will
latch in position to use the interior observation mirror.
Power Sunroof Switch — If Equipped
Refer to “Power Sunroof” in Section 3.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLinkreplaces up to three remote controls (hand-
held transmitters) that operate devices such as garage
door openers, motorized gates, lighting, or home security
systems. The HomeLink unit operates off your vehicle’s
battery.
The HomeLink buttons that are located in the sun visor
designate the three different HomeLink channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163
3

NOTE:HomeLink is disabled when the Vehicle Secu-
rity Alarm is active.
WARNING!
Your motorized door or gate will open and close while
you are training the Universal Transceiver. Do not train
the transceiver if people or pets are in the path of the
door or gate. Only use this transceiver with a garage
door opener that has a “stop and reverse” feature as
required by Federal safety standards. This includes
most garage door opener models manufactured after
1982. Do not use a garage door opener without these
safety features. Call toll-free 1–800–355–3515 or, on the
Internet at www.HomeLink.com for safety information
or assistance.
HomeLink Buttons
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run your vehicle in the garage while
training the transceiver. Exhaust gas can cause seri-
ous injury or death.
Programming HomeLink
Before You Begin
If you have not trained any of the HomeLink buttons,
erase all channels before you begin training.
To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes.
It is recommended that a new battery be placed in the
hand-held transmitter of the device being programmed
to HomeLink for more efficient training and accurate
transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage
when programming.
1. Turn the ignition switch to the ON/RUN position.
2. Hold the battery side of the hand-held transmitter
away from the HomeLink
button you wish to program.
Place the hand-held transmitter 1–3 in (3-8 cm) away
from the HomeLink button you wish to program while
keeping the indicator light in view.
3. Simultaneously press and hold both the chosen
HomeLink button and the hand-held transmitter button
until the HomeLink indicator changes from a slow to a
rapidly blinking light, then release both the HomeLink
and hand-held transmitter buttons.
Watch for the HomeLink indicator to change flash rates.
When it changes, it is programmed. It may take up to 30
seconds, or longer in rare cases. The garage door may
open and close while you train.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165
3

NOTE:
•Some gate operators and garage door openers may
require you to replace Step 3 with procedures noted in
the “Gate Operator/Canadian Programming” section.
•After training a HomeLinkchannel, if the garage
door does not operate with HomeLink and the ga-
rage door opener was manufactured after 1995, the
garage door opener may have a rolling code. If so,
proceed to the heading “Programming A Rolling Code
System.”
4. Press and hold the just-trained HomeLink button
and observe the indicator light.
If the indicator light stays on constantly, programming is
complete and the garage door (or device) should activate
when the HomeLink button is pressed. If the indicator light blinks rapidly for two seconds, and
then turns to a constant light, continue with program-
ming for a Rolling Code.
5. PROGRAMMING A ROLLING CODE SYSTEM
At the garage door opener motor (in the garage), locate
the “Learn” or “Training” button.
This can usually be found where the hanging antenna
wire is attached to the garage door opener motor (it is
NOT the button normally used to open and close the
door).
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

6. Firmly press and release the “Learn” or “Training”
button. The name and color of the button may vary by
manufacturer.
NOTE:There are 30 seconds in which to initiate the next
step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed
HomeLink
button twice (holding the button for two
seconds each time). If the device is plugged in and
activates, programming is complete.
If the device does not activate, press the button a third
time (for two seconds) to complete the training.
If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.
To program the remaining two HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to “time-out” (or quit) after several seconds of
transmission – which may not be long enough for
HomeLink to pick up the signal during programming.
1 — Garage Door Opener 2 — Training Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
3