2009 DODGE AVENGER bulb

▫Adding Washer Fluid.................. 382
▫Exhaust System...................... 383
▫Cooling System...................... 385
▫Brake System....................... 390
▫Automatic Transaxle.................. 392
▫Appearance Care And Protection From
Corrosion.......................... 395
▫Cleaning Center Console Cupholders...... 400
Fuses.............................. 400
▫Totally Integrated Power Module (TIPM).... 400
Vehicle Storage....................... 409Replacement Bulbs..................... 409
Bulb Replacement..................... 410
▫Headlight.......................... 410
▫Fog Lights......................... 412
▫Taillights, Rear Turn Signals And Backup
Lights............................. 413
▫License Plate Light................... 415
▫Center High-Mounted Stop Light......... 415
Fluids And Capacities................... 417
Fluids, Lubricants, And Genuine Parts....... 418
▫Engine............................ 418
366 MAINTAINING YOUR VEHICLE

the gas cap is properly tightened. Press the trip odometer
“Reset” button to turn off the message. If the problem
persists, the message will appear the next time the
vehicle is started. This might indicate a damaged cap. If
the problem is detected twice in a row, the system will
turn on the “Malfunction Indicator Light (MIL).” Resolv-
ing the problem will turn the MIL light off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass
an inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states that require an Inspection and Mainte-
nance (I/M), this check verifies the Malfunction
Indicator Light (MIL) is functioning and is not on
when the engine is running, and that the OBD II system
is ready for testing.Normally, the OBD II system will be ready. The OBD II
system maynotbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not
ready for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition key-actuated test,
which you can use prior to going to the test station. To
check if your vehicle’s OBD II system is ready, you must
do the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see the MIL symbol come on as part of a normal bulb
check.
MAINTAINING YOUR VEHICLE 371
7

VEHICLE STORAGE
If you will not be using your vehicle for more than 21 days,
you may want to take steps to preserve your battery.
•Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
•Disconnect the negative cable from the battery.
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS — Interior Bulb No.
Front Courtesy/Reading Light...........578/W5W
Center Courtesy/Reading Light..........578/W5W
Visor Vanity Light......................A6220
Glove Box Light.......................A6220
Shift Indicator Light.................IKLE14140
Rear Compartment (Trunk) Light............. 579NOTE:For lighted switches, see your authorized dealer
for replacement.
LIGHT BULBS — Exterior Bulb No.
Low Beam Headlight.....................9006
High Beam Headlight.....................9005
Front Park/Turn Signal/Side Marker Light. . . 3157AK
Front Fog Light......................9145/H10
Center High Mounted Stop (CHMSL)
Light...........................W16W (921)
Rear Tail/Stop Light....................3157K
Rear Turn Signal Light....................3057
Backup Light...........................3157
License Light..................... 168orW5W
MAINTAINING YOUR VEHICLE 409
7

BULB REPLACEMENT
Headlight
1. Raise the hood and locate the connector behind the
headlamp.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the totally integrated power
module aside prior to replacing the low beam headlight
on the driver’s side of the vehicle.
2. Reach into engine compartment and from behind the
lamp assembly and grasp the connector.
410 MAINTAINING YOUR VEHICLE

3. Rotate bulb and connector14turn and pull outward
from assembly.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life.4. Pull the bulb out of the socket and replace the bulb.
5. If the bulb comes in contact with any oily surface,
clean the bulb with rubbing alcohol.
6. Reinsert the bulb and socket assembly and rotate
clockwise14turn to secure.
MAINTAINING YOUR VEHICLE 411
7

Fog Lights
1. Access to the lights through the lower fascia cutout is
limited.
2. Turn the steering wheel to allow access and remove
the inner fender shield.3. Rotate bulb and connector
14turn counterclockwise.
4. Pull bulb off of connector and replace with a new one.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
412 MAINTAINING YOUR VEHICLE

2. Remove the two plastic wing nuts from the taillight
housing.
3. Grasp the taillight and pull firmly outward pushing
gently on the studs from inside to disengage the light
housing.4. Twist and remove socket from light.
5. Remove bulb from socket and replace.
414 MAINTAINING YOUR VEHICLE

License Plate Light
1. Remove two retaining screws holding the light lens in
place.
2. Gently pry the light assembly loose.
3. Pull bulb from socket, replace and reattach the light
assembly with the two retaining screws.
Center High-Mounted Stop Light
1. Open the trunk lid to find the centrally located high-
mounted stop light.
MAINTAINING YOUR VEHICLE 415
7