2009 Citroen BERLINGO FIRST DAG RHD fold seats
[x] Cancel search: fold seatsPage 6 of 123
9FAMILIARISATION-
REAR BENCH SEATS (7 SEAT VERSION)
Disarming the passenger air bag
With the ignition off , insert the
ignition key into the passenger
air bag switch 1 and turn it to the
"OFF" position.
As soon as you remove the child
seat, turn the air bag switch to the
"ON" position to activate the air
bag again. Disarming check
With the ignition switched
on (2 nd
notch), illumination
of this warning light indi-
cates that the passenger
air bag is disarmed (switch
in the "OFF" position).
The warning light remains on through-
out the duration of disarming.
79
Front air bags
These are folded in the centre of the
steering wheel for the driver and in the
fascia for the front passenger. They are
deployed simultaneously, except in cases
where the passenger air bag is disarmed.
Precautions regarding the
passenger air bag
disarm the air bag if you install a
rear-facing child seat,
activate the air bag for an adult
passenger.
78 Side air bags *
Side air bags are incorporated into the
front seat back frame, on the door side.
They are deployed independently of
each other, on whichever side the
collision occurs.
AIR BAGS
44
T h e 7 s e a t v e r s i o n i s fi t t e d w i t h a
2-seat bench in row 2 and a 3-seat
bench in row 3.
* According to version.
Page 39 of 123
41SEATS-
FRONT SEATS
The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
4. Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.
2. Armrests
These can be folded back. 3. Seat back angle adjustment
5. Storage drawer (version with
passenger air bag)
There is a storage drawer under the
front passenger seat.
To open it, lift it and pull. 6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops op-
eration.
Note: the command for activation of
heating of the seat(s) remains mem-
orised for two minutes after the igni-
tion has been switched off.
7. Access to rear seats (version with one
sliding side door only)
Do not place heavy objects
in the drawers.
A. Turn the knob.
B. Pull the lever (version
with one sliding side
door only).
Never drive with the head re-
straints removed; they must
be in place and correctly ad-
justed. Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).
Page 40 of 123
SEATS42-
MULTIFUNCTION PASSENGER SEAT
To fold the seat fully:
Pull the control 2 upwards and tilt the
whole seat.
It is not necessary to remove the
head restraint.
This provides access to a box which
enables you to store objects so that
they cannot be seen from outside the
vehicle. I f y o u r v e h i c l e i s n o t fi t t e d w i t h a l o a d
blocking partition, it can accommo-
date long objects (up to 2.10 m).
These must be placed on the front
e d g e o f t h e fl o o r a n d s e c u r e d u s i n g
the rear bar of the boot or using the
lashing rings.
To fold the seat back:
Pull the control
1 upwards and tilt the
seat back.
T h i s p r o v i d e s a fl a t s u r f a c e , r e c e s s -
es for drinks and a strap for retaining
documents.
Page 41 of 123
43SEATS-
To fold the rear bench seat:
- lower the head restraint,
- press control 1 to unlock the seat
back 2 ,
- fold the seat back 2 onto the seat,
- place the seat in the "folded" posi- tion. When repositioning:
- tilt the folded seat rearwards,
- lift the seat back,
- check that the seat is locked cor-
rectly.
Take care not to trap the seat belts.
REAR BENCH SEAT(5 SEAT VERSION)
HEAD RESTRAINT
This is of the "comma" type.
High position: press the two tabs at
the same time, lift the head restraint
and raise it.
Low position: push the two tabs at
the same time and press the top to
lower the head restraint.
To remove the head restraint: place
it in the high position, lift it then re-
move it.
Store it inside the vehicle, securing
i t fi r m l y .
To install the head restraint: engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
Page 42 of 123
SEATS44-
REAR BENCH SEATS (7 SEAT VERSION)
The bench seats of row 2 and row 3
are independent and adjustable.
Row 2 bench seat
Placing the bench seat in the
table position
- Lower the head restraints fully.
- Operate the control to fold the seat back onto the bench seat
cushion.
Returning the seat back to
the sitting position
- Return the seat back to its original position and check that it is se-
cured on the pillar of the vehicle. Placing the bench seat in the fully
folded position
- Place the seat in the table posi-
tion.
- Pull the handle, located behind the bench seat, to release the
feet from their anchorage on the
fl o o r .
- Tilt the bench seat forwards.
Returning the bench seat to its original position
Before folding the bench seat,
ensure that:
- in row 3, no passenger's foot is at one of the bench seat anchor-
a g e s o n t h e fl o o r ,
- the seat belt is available for the side passenger.
- fold back the bench seat.
Page 43 of 123
45SEATS-
Row 3 bench seat
Placing the seat back in the table
position
- Lower the head restraints fully.
- Operate the two controls simulta-neously to fold the seat back onto
the bench seat cushion.
Returning the seat back to the sitting position
- Return the seat back to its original position and check that it is se-
cured on the pillars of the vehicle. Placing the bench seat in the fully
folded position
- Place the seat in the table posi-
tion.
- Raise the handle, located behind the bench seat, to release the
feet from their anchorage on the
fl o o r .
- Tilt the bench seat forwards.
Returning the bench seat to its
original position
- Before folding back the bench seat, ensure that the seat belt
is available for the side passen-
gers.
- Fold back the bench seat.
Access to row 3
From the vehicle's right-hand sliding
door, a passage next to the row 2
bench seat provides access to the
row 3 bench seat.
Good practice
Do not place hard or heavy
objects on the seat backs
forming a table, they could
become dangerous projectiles in the
event or sharp braking or impact.
Following the various operations:
- do not remove a head restraint w i t h o u t s t o r i n g i t , fi x i t t o a s u p -
port in the vehicle,
- do not block the passage to row 3,
- ensure that the passengers can always access the seat belts and
fasten them easily,
- a passenger must never take his seat without adjusting and fasten-
ing his seat belt.
- a passenger seated in row 3 must ensure that he does not obstruct
the row 2 bench seat anchoring
recesses.
Page 52 of 123
53SEATS-
The driver must ensure that
the passengers use the seat
belts correctly and that they
are all properly restrained
before setting off.
Wherever you are seated in the ve-
hicle, always fasten your seat belt,
even for short journeys.
Do not invert the seat belt buckles as
t h e y w i l l n o t f u l fi l t h e i r r o l e f u l l y .
If the seats have armrests * , the lap
part of the seat belt must always
pass under the armrest.
T h e s e a t b e l t s a r e fi t t e d w i t h a n i n -
ertia reel permitting automatic adjust-
ment of the length of the strap to your
size. The seat belt is stored automat-
ically when not in use.
Before and after use, ensure that the
seat belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the
pelvis.
The upper part must be positioned in
the hollow of the shoulder.
T h e i n e r t i a r e e l s a r e fi t t e d w i t h a n a u -
tomatic locking device which comes
into operation in the event of a colli-
sion, on emergency braking or if the
vehicle rolls over. You can release
the device by pulling rapidly on the
strap and releasing it. In order to be effective, a seat belt:
- must be tightened as close to the
body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must be pulled in front of you with a smooth movement, checking
that it does not twist,
- must not be transformed or modi- fi e d t o a v o i d a l t e r i n g i t s p e r f o r m -
ance.
In accordance with current safety
regulations, all repairs and checks
must be carried out by a CITROËN
dealer who guarantees that the work
is carried out correctly.
Have your seat belts checked regu-
larly by a CITROËN dealer and par-
ticularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by CITROËN dealers.
* According to model.
Recommendations for children:
- use a suitable child seat if the pas-
senger is less than 12 years old or
s h o r t e r t h a n o n e m e t r e fi f t y ,
- do not use the strap-guide * when a child seat is installed.
- never use the same seat belt to secure more than one person,
- never allow a child to travel on your lap.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags. Triggering of the pre-tensioners
is accompanied by a slight emission
of harmless smoke and a noise, due
to the activation of the pyrotechnic
cartridge incorporated in the system.
In all cases, the air bag warning lamp
comes on.
Following an impact, have the seat
belts system checked, and if neces-
sary replaced, by a CITROËN dealer.
After folding or moving a
seat or rear bench seat,
ensure that the seat belt
is positioned and rolled up
correctly.
Page 73 of 123
71COMFORT AND SAFETY-
1. Load-space cover
To install it:
- position the front ends of the load space cover on its support and
press gently to put it in place,
- unfold the load space cover fully,
- position the rear ends of the load space cover on its support and
press gently to put it in place.
To remove it:
- unclip the rear ends,
- fold the load space cover fully,
- unclip the front ends and remove the load space cover.
To store it, fold it like an accordion.
Do not roll it . 2. High load retaining net
T h e h i g h l o a d r e t a i n i n g n e t c a n b e fi t -
ted behind the front or rear seats.
Open the covers
A of the correspond-
ing upper fastenings.
Fit the ends of the metal bar in these
fastenings.
Secure the two net strap hooks be-
hind the front seats, with the rear
seat folded, or in the stowing rings B
o n t h e fl o o r .
The rings are located directly below
the corresponding upper fastenings.
Pull the two straps C taut. 3. Stowing rings
4. Side door storage
compartments
5. Trays between the front and rear seats
6. Seat back storage pockets
7. Cup holder