2009 CHERY TIGGO catalytic converter

Downloaded from www.Manualslib.com manuals search engine 26. Remove the catalytic converter to exhaust manifoldbolts (1).
27. Raise and support the vehicle.
28. Remove the front axle shaft (See Front Axle Shaft Removal & Installation in Section 09 Driveline & Axle).
29. Drain the engine oil.
30. Lower the vehicle and install engine lift chain hangers.
31. Remove the bolts (1) securing the front engine mount.
(Tighten: Engine front mount bolt to 60 N·m)
32. Remove the bolts (1) securing the rear engine mount.
(Tighten: Engine rear mount bolt to 60 N·m)
ON-VEHICLE SERVICE
LTSM020201
BESM080035 LTSM020207
02
02–35Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4. Remove the three bolts (1) securing the exhaustmanifold to the catalytic converter assembly.
5. Disconnect the catalytic converter assembly from the manifold.
6. Remove the exhaust manifold nuts (1). (Tighten: Exhaust manifold nuts to 25 N·m)
7. Remove and discard manifold gasket (1).
8. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020201
BESM020033
LTSM020169
02–42Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 25. Remove the catalytic converter to exhaust manifoldbolts (1).
26. Raise and support the vehicle.
27. Remove the front axle shaft (See Front Axle Shaft Removal & Installation in Section 09 Driveline & Axle).
28. Drain the engine oil.
29. Lower the vehicle and install engine lift chain hangers.
30. Remove the bolts (1) securing the front engine mount.
(Tighten: Engine front mount bolt to 60 N·m)
31. Remove the bolts (1) securing the rear engine mount.
(Tighten: Engine rear mount bolt to 60 N·m)
ON-VEHICLE SERVICE
LTSM020201
BESM080035 LTSM020207
02–109Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4. Remove the three bolts (1) securing the exhaustmanifold to the catalytic converter assembly.
5. Disconnect the catalytic converter assembly from the manifold.
6. Remove the exhaust manifold nuts (1). (Tighten: Exhaust manifold nuts to 25 N·m)
7. Remove the exhaust manifold.
8. Remove and discard manifold gasket (1).
9. Installation is in the reverse order of removal.
ON-VEHICLE SERVICE
LTSM020201
BESM020033
LTSM020169
02
02–11 6Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 21. Disconnect the following automatic transaxle elec-trical connectors:• Output shaft sensor (1)
• Input shaft sensor (2)
• Electromagnetic valve switch connector (3)
• Gear switch connector (5)
22. Disconnect the transaxle fluid lines (6) using a suit- able tool.
23. Remove the shift cable (4) from the transaxle assembly.
24. Remove the catalytic converter to exhaust manifold bolts (1).
(Tighten: Exhaust manifold bolt to 49 ± 5 N·m)
25. Remove the front axle shaft (See Front Axle Shaft Removal & Installation in Section 09 Driveline & Axle).
26. Raise and support the vehicle.
27. Drain the engine oil.
28. Remove the power steering pump fluid line and set aside (See Power steering pump Removal & Installation in Section 11 Steering).
29. Lower the vehicle and install engine lift chain hangers.
ON-VEHICLE SERVICE
LTSM080153
LTSM020189
02–186Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Exhaust Manifold
Removal & Installation
1. Remove the bolts attaching the exhaust manifold heat shield.(Tighten: Exhaust manifold heat shield bolts to 14 N·m)
2. Remove the exhaust manifold heat shield.
3. Remove the three bolts securing the exhaust manifold to the catalytic converter assembly. (Tighten: Exhaust manifold to catalytic converter bolts to 49 ± 5 N·m)
4. Disconnect the catalytic converter assembly from the manifold.
5. Remove the exhaust manifold nuts. (Tighten: Exhaust manifold nuts to 29 ± 3 N·m)
6. Remove the exhaust manifold from the cylinder head.
7. Remove and discard exhaust manifold gasket.
1 - Exhaust Manifold Heat Shield
2 - Engine Hanger
3 - Oxygen Sensor4 - Exhaust Manifold
5 - Exhaust Manifold Gasket
ON-VEHICLE SERVICE
LTSM020179
02–200Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Engine Cranks Normal But Will Not Start
The following conditions apply to this symptom:
•The engine cranks at normal speed.
• The engine will not start.
• The battery is fully charged.
1.PRELIMINARY CHECKS
CAUTION:
Extended cranking because of a No Start can load the exhaust system with raw fuel, damaging the
catalytic converter after the engine starts.
•Carry out the following preliminary checks:
Fuel quality
Electrical connections
Intake air tube integrity
Fuses and relays
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair as necessary.
Verify the symptom no longer exists.
2.CHECK DTC
• Turn the ignition switch on.
• With the scan tool X-431, select view DTC.
Are there any DTCs present?
Ye s>>See the Diagnostic Trouble Code (DTC) List.
Go to the specific diagnostic test to troubleshoot the DTC.
No
>>Go to the next step.
3.TRY TO START THE ENGINE WITH THE THROTTLE CLOSED
• Attempt to start the engine.
Does the engine start now with the throttle closed?
Ye s>>Verify the symptom no longer exists.
No
>>Go to the next step.
4.CHECK EXHAUST SYSTEM
• Inspect the vehicles exhaust system for restriction.
Is there a restriction in the exhaust system?
Ye s>>Repair as necessary.
No
>>Go to the next step.
ELECTRONIC ENGINE CONTROLS - 2.4L ENGINE SYMPTOM DIAGNOSIS
03
03–545Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine EXHAUST
07
CONTENTSpage
Exhaust System ...................................................................... 07-1
EXHAUST SYSTEM
GENERAL INFORMATION07-2
Description 07-2
Operation 07-3
Specifications 07-3
DIAGNOSIS AND TESTING07-4
Exhaust System Diagnostic Chart 07-4
ON-VEHICLE SERVICE07-5
Exhaust Pipe Assembly 07-5
Removal & Installation - 1.6L & 1.8L &
2.0L 07-5 Removal & Installation - 2.4L 07-5
Muffler 07-6
Removal & Installation 07-6
Catalytic Converter 07-6
Description 07-6
Operation 07-6
Removal & Installation 07-7
07
07–1Chery Automobile Co., Ltd.