Page 6 of 462

Front Seats
Power Seats
The power seat controls
are located on the outboard
side of the seat cushions.
Move the seat forward or rearward by sliding the
horizontal control forward or rearward.
Raise or lower the front part of the seat cushion by
moving the front of the horizontal control up or down.
Raise or lower the rear part of the seat cushion by
moving the rear of the horizontal control up or down.
Raise or lower the entire seat by moving the entire
horizontal control up or down.
Use the vertical control to recline the seatback.
SeePower Reclining Seatbacks on page 1-4.
Power Lumbar
The driver and passenger
seatback lumbar support
switches are located on the
outboard sides of the seats.
Use the power seat controls rst to get the proper
position, then continue with the lumbar adjustment.
The top lumbar switch adjusts support to the middle
seatback and the bottom lumbar switch adjusts
support to the lower seatback.
Press the front of the switch to increase support and
the rear of the switch to decrease support.
Remember to readjust lumbar support as your seating
position changes.
1-2
Page 97 of 462

Outside Automatic Dimming Mirror
The driver’s side mirror adjusts for the glare of
headlamps behind you. This feature is controlled by the
on and off settings on the inside automatic dimming
rearview mirror. SeeAutomatic Dimming Rearview
Mirror on page 2-38for more information.
Park Assist Mirror
Vehicles with the memory package are capable of having
the passenger mirror tilt to a preselected position when
the vehicle is in R (Reverse). This feature lets the driver
view the curb when parallel parking. If further adjustment
is needed after the mirror is tilted, the mirror switch may
be used. The mirror then returns to this new position
when the vehicle is shifted into R (Reverse).
When the vehicle is shifted out of R (Reverse) and a
ve-second delay has occurred, the passenger
side mirror returns to its original position.
Turn this feature on or off through the Driver Information
Center (DIC). SeeDIC Vehicle Personalization on
page 3-72for more information.
Outside Convex Mirror
{CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you could
hit a vehicle on the right. Check the inside mirror or
glance over your shoulder before changing lanes.
The passenger side mirror is convex shaped. A convex
mirror’s surface is curved so more can be seen from
the driver’s seat.
Outside Heated Mirrors
<(Rear Window Defogger):Press to heat the
mirrors. See “Rear Window Defogger” underDual
Climate Control System on page 3-36.
Store the preferred mirror position by using the memory
option. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-3.
2-39
Page 362 of 462

Headlamp Aiming
The high intensity discharge (HID) visual optical aiming
type headlamps have been preset at the factory and
should need no further adjustment. If the headlamps
need to be re-aimed, it is recommended to see your
dealer/retailer for service. However, it is possible to
re-aim the headlamps as described in the following
procedure.
Notice:To make sure the headlamps are aimed
properly, read all the instructions before beginning.
Failure to follow these instructions could cause
damage to headlamp parts.
The vehicle should be properly prepared as follows:
The vehicle should be placed so the headlamps are
25 ft (7.6 m) from a light colored wall.
The vehicle must have all four tires on a perfectly
level surface which is level all the way to the wall.
The vehicle should be placed so it is perpendicular
to the wall.
The vehicle should not have any snow, ice, or mud
attached to it.
The vehicle should be fully assembled all other
work stopped while headlamp aiming is being done.
The vehicle should be normally loaded with a
full tank of fuel and one person or 160 lbs (75 kg) on
the driver seat.
The tires should be properly in ated.
Start the vehicle and rock it to level the suspension.
Headlamp aiming is done with the low-beam
headlamps. The high-beam headlamps are correctly
aimed if the low-beam headlamps are aimed properly.
The headlamp aiming
device is under the hood
near the headlamps.
6-42