2009 CADILLAC XLR lock

You can also pressGon the keyless access
transmitter to open the trunk. To disable this feature,
see “Valet Lockout Switch” underTheft-Deterrent
Systems on page 2-20.
You may passively enter the trunk when you squeeze the
trunk release sensor located on the rear of the trunk lid
under the emblem, as long as you have your transmitter
with you. The vehicle must be in PARK (P) and the valet
lockout switch must be off. SeeValet Lockout Switch on
page 2-22.
To close the trunk, press
Gon the underside of the
trunk lid.
To stop the trunk lid while it is closing, do one of the
following:
Press the trunk lock release button located on the
instrument panel.
Use the vehicle key.
Squeeze the trunk release sensor located on the
rear of the trunk lid.
PressGon the keyless access transmitter.
Press the trunk close button on the underside of the
trunk lid.
To begin opening the trunk from the stopped position,
use any of the methods above, except pressing the trunk
close button.
To resume closing the power trunk lid, press the trunk
close button on the underside of the trunk lid.
If the vehicle has lost battery power, you can still open
the trunk using the vehicle key. SeeKeys on page 2-3
for more information.
2-15

Power Windows
{CAUTION:
Leaving children in a vehicle with the keys is
dangerous for many reasons, children or others
could be badly injured or even killed. They could
operate the power windows or other controls or
even make the vehicle move. The windows will
function and they could be seriously injured or
killed if caught in the path of a closing window.
Do not leave keys in a vehicle with children.
When there are children in the rear seat use the
window lockout button to prevent unintentional
operation of the windows.
The power window
switches are located on
each door near the armrest.Press the front of the switch to the rst position to open
the window to the desired level. Lift the front of the
switch to the rst position to close the window.
The vehicle has Retained Accessory Power (RAP) that
allows power windows to be used once the ignition has
been turned off. For more information, seeRetained
Accessory Power (RAP) on page 2-25.
Power Window Initialize
After a power reconnect such as battery replacement,
the express-up and index-up features will not function
until the system is initialized. Once power is restored,
do the following:
1. Close the door.
2. Raise the window by lifting the front of the power
window switch.
3. Lift the switch for three seconds after the window is
closed. Release the switch. Then lift the switch
again for three seconds.
The express-up system must be initialized to operate
the windows with the door open.
2-18

Window Indexing
This feature automatically lowers the window a small
amount when the door is opened. Then, when the door
is closed, the window will raise to its full up position.
Sun Visors
Notice:Raising or lowering the retractable hardtop
with the visor or the visor vanity mirror cover up
may cause damage to the visor or mirror cover.
Always return the visor to the center mount or lower
the cover on the visor vanity mirror before raising
or lowering the retractable hardtop.
Swing down the visor to block out glare. It can also be
detached from the center mount and moved to the side.
Lighted Visor Vanity Mirrors
Swing the visor down and lift the cover. The lamp will
automatically come on when the cover is opened.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some cities.
This vehicle has theft-deterrent features, however,
they do not make it impossible to steal.
Theft-Deterrent System
With this system, the
security light will ash
when the door is open and
locked with the power
door lock switch.
If this light is on continuously while the engine is
running, your vehicle needs service.
2-20

Arming the System
To arm the system:
PressQon the keyless access transmitter.
Open the door. Lock the door with the power door
lock switch. The security light should ash. Remove
the keyless access transmitter from the interior of the
vehicle and close the door. The security light will stop
ashing and stay on. After 30 seconds, the light
should turn off.
The vehicle can be programmed to automatically lock
the doors and arm the system when you exit the
vehicle. SeeDIC Vehicle Personalization on
page 3-72.
Now, if a door or the trunk lid is opened without the
keyless access transmitter, the alarm will go off.
The horn will sound for two minutes, then it will go
off to save battery power. And, the vehicle will not
start without a keyless transmitter present.
The theft-deterrent system will not arm if you lock the
driver door with the power door lock switch after
the doors are closed.
If the passenger stays in the vehicle when you leave with
the keyless access transmitter, have the passenger lock
the vehicle after the doors are closed. This way the alarm
will not arm, and the passenger will not set it off.
Testing the Alarm
To test the system:
1. Close the trunk lid.
2. Lower the window on the driver door.
3. Manually arm the system.
4. Close the doors and wait 30 seconds.
5. Reach through the open window and manually pull
the release lever on the oor.
6. Turn off the alarm by pressing
Kon the transmitter.
If the alarm is inoperative, check to see if the horn
works. If not, check the horn fuse. SeeFuses and Circuit
Breakers on page 6-83. If the horn works, but the
alarm doesn’t go off, see your dealer/retailer.
Disarming the System
Always use the keyless access transmitter to unlock a
door either by pressing
Kon the transmitter or by
squeezing the door handle sensor while you have the
transmitter with you. Unlocking a door any other way will
set off the alarm. If the alarm sounds, press
Kon the
keyless access transmitter to disarm it.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-21

Valet Lockout Switch
This switch is located
inside the glove box.
Press ON to disable the use of the trunk and convertible
top. The trunk cannot be opened except by using the key
if the valet lockout is on.
Press OFF to enable the use of the trunk and
convertible top.
Locking the glove box with the key will also help to
secure the vehicle.
Immobilizer
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
2-22

Automatic Transmission Operation
There are several different positions for the shift lever.
P (Park):This position locks the rear wheels. It is
the best position to use when starting the engine
because the vehicle cannot move easily.
{CAUTION:
It is dangerous to get out of the vehicle if the shift
lever is not fully in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the engine is running
unless you have to. If you have left the engine
running, the vehicle can move suddenly. You or
others could be injured. To be sure the vehicle will
not move, even when you are on fairly level ground,
always set the parking brake and move the shift
lever to P (Park). SeeShifting Into Park on
page 2-33.
Be sure the shift lever is fully in P (Park) before starting
the engine.
The vehicle has an automatic transmission shift lock
control system. You have to fully apply the regular brakes
rst and then press the shift lever button before you can
shift from P (Park) when the vehicle is running. If you
cannot shift out of P (Park), ease pressure on the shift
lever and push the shift lever all the way into P (Park)
as you maintain brake application. Then press the shift
lever button and move the shift lever into another gear.
SeeShifting Out of Park on page 2-35.
2-28

Leaving the Vehicle With the Engine
Running
{CAUTION:
It can be dangerous to leave the vehicle with the
engine running. The vehicle could move suddenly if
the shift lever is not fully in P (Park) with the parking
brake rmly set. And, if you leave the vehicle with
the engine running, it could overheat and even
catch re. You or others could be injured. Do not
leave the vehicle with the engine running.
If you have to leave the vehicle with the engine running,
be sure the vehicle is in P (Park) and the parking brake is
rmly set before you leave it. After you have moved the
shift lever into P (Park), hold down the regular brake
pedal. See if you can move the shift lever away from
P (Park) without rst pulling it toward you. If you can, it
means that the shift lever was not fully locked into
P (Park).
Torque Lock
If you are parking on a hill and you do not shift the
transmission into P (Park) properly, the weight of the
vehicle may put too much force on the parking pawl in
the transmission. You may nd it difficult to pull the
shift lever out of P (Park). This is called “torque lock.”
To prevent torque lock, set the parking brake and
then shift into P (Park) properly before you leave the
driver seat. To nd out how, see “Shifting Into Park”
listed previously in this section.
When you are ready to drive, move the shift lever out of
P (Park) before you release the parking brake.
If torque lock does occur, you may need to have another
vehicle push yours a little uphill to take some of the
pressure from the parking pawl in the transmission, so
you can pull the shift lever out of P (Park).
2-34

Shifting Out of Park
Shift lock release prevents shifting out of P (Park)
unless the vehicle is running or in Accessory mode and
the brake pedal is applied.
The shift lock release is always functional except in
the case of an uncharged or low voltage (less than
9-volt) battery. SeeJump Starting on page 6-36for
more information.
To shift out of P (Park) use the following:
1. Apply the brake pedal.
2. Press the shift lever button.
3. Move the shift lever to the desired position.If you still are unable to shift out of P (Park):
1. Fully release the shift lever button.
2. While holding down the brake pedal, press the shift
lever button again.
3. Move the shift lever to the desired position.
If you still cannot move the shift lever from P (Park),
consult your dealer/retailer or a professional towing
service.
Parking Over Things That Burn
{CAUTION:
Things that can burn could touch hot exhaust
parts under the vehicle and ignite. Do not park
over papers, leaves, dry grass, or other things that
can burn.
2-35