2009 BUICK LACROSSE manual radio set

TURN SIGNAL ON
This message displays as a reminder to turn off the
turn signal if you drive your vehicle for more than about
0.75 mile (1.2 km) with a turn signal on. SeeTurn
Signal/Multifunction Lever on page 3-7.
This message displays and a chime sounds only when
the ignition is in ON/RUN. This message clears from
the DIC if the turn signal is manually turned off, a turn
is completed, or the message is acknowledged.
DIC Vehicle Personalization
Your vehicle may have customization capabilities that
allow you to program certain features to one preferred
setting. Customization features can only be programmed
to one setting on the vehicle and cannot be programmed
to a preferred setting for two different drivers. The
customization features include the following:
Exterior lighting delay
Interior lighting delay
Delayed locking
Content theft
Remote keyless entry feedback
Remote startYour vehicle may also have personalization capabilities
that allow you to program certain features to a preferred
setting for up to two drivers. The rst personalized key
corresponds to driver 1 and the second personalized key
corresponds to driver 2. The personalization features
include the following:
Radio station presets
Auto door unlock preferences
Remote keyless entry unlock preferences
All of the customization and personalization options
may not be available on your vehicle. Only the options
available will be displayed on the DIC.
The default settings for the customization and
personalization features were set when your vehicle
left the factory, but may have been changed from their
default state since then.
The customization preferences are automatically
recalled.
The driver’s personalization preferences are recalled by
using the key programmed for driver 1 or 2.
3-74

Finding a Station
BAND:Press to choose between FM1, FM2, AM, or
XM1orXM2.
e(Tune):Turn to select radio stations.
oSEEKp:Press and release to go to the previous or
the next station and stay there.
To scan stations, press and hold either arrow for more
than two seconds. SCAN or SCN displays and the radio
beeps once. The radio goes to a station, plays for a few
seconds, and then goes to the next station. Press either
arrow again or one of the pushbuttons to stop scanning
presets.
To scan preset stations, press and hold either arrow for
more than four seconds. PSCAN or PSC displays and the
radio beeps twice. The radio goes to a preset station,
plays for a few seconds, then goes to the next preset
station. Press either arrow again or one of the
pushbuttons to stop scanning presets.The radio seeks and scans stations only with a strong
signal that are in the selected band.
SCAN:On the radio with six-disc CD, press until
SC displays. The radio goes to a station, plays for
a few seconds, and then goes to the next station.
Press again to stop scanning stations.
The radio scans stations only with a strong signal that
are in the selected band.
INFO (Information) (XM Satellite Radio Service Only):
The vehicle’s radio may have an INFO button. If the
current station on the radio has a message, the
information symbol displays. Press to see the message.
If the entire message is not displayed, parts of the
message appears every three seconds. To manually
scroll through the message, press and release the
INFO button.
When a message is not available from a station,
NO INFO displays.
3-85

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, six AM, six XM1
and six XM2) can be programmed on the six numbered
pushbuttons.
To program either radio:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM, or XM1™ or
XM2™ (if equipped).
3. Tune to the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until the radio beeps once. When
that numbered pushbutton is pressed again, the
station and equalization that were stored, returns.
6. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
e
(Bass/Treble):Press and release until BASS or
TREBLE displays. Turn
eto increase or to decrease
the bass or treble.
Press and hold
eto adjust the bass and treble to the
middle position. The radio beeps once.
To adjust all tone and speaker controls to the middle
position, press and hold
ewhen no tone or speaker
control displays. ALL CENTERED displays and the
radio beeps once.
EQ (Equalization):Press to select customized
equalization settings.
To return the bass and treble to the manual mode,
press and release until BASS or TREBLE displays.
3-86

Playing a Specic Loaded CD
For every CD loaded, a number displays. To play a
specic CD, press the numbered pushbutton that
corresponds to the CD. A small bar appears under
the CD number that is playing and the track number
displays.
Z(Eject):Press to eject CD(s).
To eject the CD that is currently playing, press and
release.
To eject multiple CDs:
1. Press and hold the
Zbutton for two seconds.
The radio beeps once and the indicator light,
located to the right of the slot, begins to ash
and EJECT ALL displays.
2. Once the light stops ashing, REMOVE CD #
displays. The CD ejects and can be removed.
Once the CD is removed, the indicator light begins
ashing again and another CD ejects.
To stop ejecting the CDs, press the LOAD or
the
Zbutton.If the CD is not removed, after 25 seconds, the CD is
automatically pulled back into the player. If a CD is
pushed back into the player, before the 25 second time
period is complete, the player senses an error and
tries to eject the CD several times before stopping.
Do not repeatedly press the
Zbutton to eject a CD
after trying to push it in manually. The player’s 25-second
eject timer resets at each press of the eject button,
causing the player to not eject the CD until the 25-second
time period has elapsed.
1
s(Reverse):Press to reverse within the current
track.
2
\(Fast Forward):Press to fast forward within the
current track.
3
N(Repeat):Depending on the radio, press to
hear a track over again. REPEAT TRACK displays.
The current track continues to repeat.
For the radio with a Six-Disc CD player, press to repeat
one track or an entire CD.
3-90

x(Previous):Press to go to the previous radio
station. The radio seeks stations only with a strong
signal that are in the selected band.
To scan stations, press and hold
cxfor
two seconds until a beep sounds. The radio goes
to a station, play for a few seconds, then goes to the
next station. Press
cxagain to stop scanning.
While a CD is playing, press
cxto go to the previous
track.
c(Phone on Hook):Press to reject an incoming call,
or end a current call.
b>(Push to Talk/Mute):Press to silence the vehicle
speakers only. Press again or any other radio button,
to turn the sound on.For vehicles with OnStar
®or Bluetooth systems press
and hold
b>for longer than two seconds to interact
with those systems. SeeOnStar®System on page 2-39
andBluetooth®on page 3-99in this manual for more
information.
BAND:Press to switch between FM1, FM2, AM, or
XM1orXM2.
1–6 (Preset Pushbuttons):Press to play stations
that are programmed on the radio preset pushbuttons.
The radio seeks preset stations only with a strong signal
that are in the selected band.
When a CD is playing in the six-disc CD changer, press
this button to go to the next available CD, if multiple
CDs are loaded.
+
x/−x(Volume):Press to increase or to decrease
the volume.
3-111