2009 BUICK LACROSSE audio

Playing the Radio
P
(Power):Press to turn the system on and off.
v(Volume):Turn to increase or to decrease the
volume.
DISP (Display):Press to switch the display between
the radio station frequency and time of day. While
the ignition is off, press this button to display the time.
If the vehicle’s radio has XM™, press the DISP
button while in XM mode to retrieve four different
categories of information related to the current song
or channel: Artist, Song Title, Category or PTY,
Channel Number/Channel Name.
To change the default on the display, press the DISP
button until the desired display appears, then hold DISP
for two seconds. The radio beeps once and the selected
display becomes the default.SCV (Speed Compensated Volume):If the vehicle’s
radio has Speed Compensated Volume (SCV), the audio
system adjusts automatically to make up for road and
wind noise while driving.
Set the volume at the desired level. Press this button
to select LOW, MEDIUM, or HIGH. Depending on the
radio, the selection may be SPEED VOL MIN (volume
minimum), SPEED VOL MED (volume medium), or
SPEED VOL MAX (volume maximum). Each higher
setting allows for more volume compensation at faster
vehicle speeds. Then while driving, SCV increases the
volume, as necessary, to overcome noise at any speed.
The volume level should always sound the same while
driving. NONE displays if the radio cannot determine the
vehicle speed. To turn SCV off, press SCV until OFF or
SPEED VOL OFF displays.
3-84

Scanning Categories (CAT)
(XM Satellite Radio Service Only)
To scan a desired category:
1. Press the CAT button to enter the category select
mode. The current category displays.
2. Turn the
eknob to select a category.
3. Press either SEEK arrow for two seconds once the
desired category is displayed, to scan the stations
in that category.
4. Press either SEEK arrow again to stop scanning.
If the radio cannot nd the desired category, NOT
FOUND displays and the radio returns to the last
station that was being listened to.
Radio Messages
CALIBRATE:The audio system has been calibrated
for the vehicle from the factory. If CALIBRATE displays, it
means that the radio has not been congured properly for
the vehicle and it must be returned to your dealer/retailer
for service.LOCKED:If LOCKED displays, it means the
THEFTLOCK
®system has locked up. Take the
vehicle to your dealer/retailer for service.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer.
XM Satellite Radio Service
XM is a satellite radio service that is based in the
48 contiguous United States and 10 Canadian provinces.
XM Satellite Radio has a wide variety of programming
and commercial-free music, coast-to-coast, and in
digital-quality sound. During your trial or when you
subscribe, you will get unlimited access to XM Radio
Online for when you are not in the vehicle. A service
fee is required to receive the XM service. For more
information, contact XM at xmradio.com or call
1-800-929-2100 in the U.S. and xmradio.ca or
call 1-877-438-9677 in Canada.
Radio Messages for XM Only
SeeXM Radio Messages on page 3-98later in this
section for further detail.
3-88

Playing a CD
Insert a CD partway into the slot, label side up. The
player pulls it in and the CD begins playing. To insert a
CD while the ignition is off, rst press the
Zbutton
or the DISP knob.
If the ignition or radio is turned off while a CD is in
the player, it stays in the player. While the ignition
or radio is turned on, the CD starts to play where it
stopped, if it was the last selected audio source.
When the CD is inserted, the CD symbol displays. As
each new track starts to play, the track number displays.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs and
the smaller CDs are loaded in the same manner.
For vehicles that have a radio with a Six-Disc CD player:
LOAD:Press to load CDs into the CD player.
This CD player holds up to six CDs.
To insert one CD:
1. Turn the ignition on.
2. Press and release the LOAD button.3. Wait for the indicator light, located to the right of the
slot, to turn green.
4. Load a CD. Insert the CD partway into the slot,
label side up. The player pulls the CD in.
To insert multiple CDs:
1. Turn the ignition on.
2. Press and hold the LOAD button for two seconds.
The radio beeps once and the indicator light,
located to the right of the slot, begins to ash
and MULTI LOAD # displays.
3. Once the light stops ashing and turns green,
INSERT CD # displays, load a CD. Insert the CD
partway into the slot, label side up. The player pulls
the CD in.
Once the CD is loaded, the indicator light begins
ashing again. Once the light stops ashing and turns
green, another CD can be loaded. The CD player takes
up to six CDs.
To load more than one CD but less than six, complete
Steps 1 through 3. When nished loading CDs, press the
LOAD button to cancel the loading function. The radio
begins to play the last CD loaded.
If more than one CD has been loaded, a number for
each CD displays.
3-89

Care of the CD Player
Do not add any label to a CD, it could get caught in the
CD player. If a CD is recorded on a personal computer
and a description label is needed, try labeling the top
of the recorded CD with a marking pen.
The use of CD lens cleaners for CDs is not advised,
due to the risk of contaminating the lens of the CD optics
with lubricants internal to the CD player mechanism.
Notice:If a label is added to a CD, or more than
one CD is inserted into the slot at a time, or an
attempt is made to play scratched or damaged CDs,
the CD player could be damaged. While using the CD
player, use only CDs in good condition without any
label, load one CD at a time, and keep the CD player
and the loading slot free of foreign materials, liquids,
and debris.
If an error displays, see “CD Messages” later in this
section.
Using an MP3
MP3 CD-R Disc
MP3 Format
If you burn an MP3 disc on a personal computer:
Make sure the MP3 les are recorded on a
CD-R disc.
Do not mix standard audio and MP3 les on
one disc.
Make sure playlists have a .mp3 or .wpl extension,
other le extensions may not work.
Files can be recorded with a variety of xed or
variable bit rates. Song title, artist name, and album
will be available for display by the radio when
recorded using ID3 tags version 1 and 2.
Create a folder structure that makes it easy to nd
songs while driving. Organize songs by albums
using one folder for each album. Each folder
or album should contain 18 songs or less.
Make sure to nalize the disc when burning an MP3
disc, using multiple sessions. It is usually better to
burn the disc all at once.
3-95

The player is able to read and play a maximum of
50 folders, 50 playlists, 10 sessions, and 255 les.
Long le names, folder names, or playlist names could
use more disc memory space than necessary. To
conserve disc space, keep the length of the le, folder, or
playlist name brief. MP3 CDs do not require le folders.
The system can support up to 11 folders in depth. The
depth of the folders should be kept down to make it easier
while locating a folder during playback. All items over the
maximum are ignored.
Root Directory
The root directory is treated as a folder. If the root
directory has compressed audio les, the directory
displays as F1 ROOT. All les contained directly under
the root directory are accessed prior to any root directory
folders. However, playlists (Px) always are accessed
before root folders or les.
Empty Directory or Folder
If a root directory or a folder exists somewhere in the
le structure that contains only folders/subfolders and
no compressed les directly beneath them, the player
advances to the next folder in the le structure that
contains compressed audio les and the empty folder
does not display.
No Folder
If a CD has no folder, only compressed les or playlists
are located under the root folder. The next and
previous folder functions have no function on a CD that
is recorded without folders or playlists. When displaying
the name of the folder the radio displays ROOT.
Order of Play
Tracks are played in the following order:
Play begins from the rst track in the rst playlist
and continues sequentially through all tracks in
each playlist. When the last track of the last playlist
has played, play continues from the rst track of
the rst playlist.
If the CD does not contain any playlists, then play
begins from the rst track under the root directory.
When all tracks from the root directory have played,
play continues from les according to their numerical
listing. After playing the last track from the last folder,
play begins again at the rst track of the rst folder or
root directory.
When play enters a new folder, the display does
not automatically show the new folder name unless
the folder mode is chosen as the default display.
See “DISP” later in this section for more information.
The new track name displays.
3-96

File System and Naming
The song name that displays is the song name that is
contained in the ID3 tag. If the song name is not present
in the ID3 tag, then the radio displays the le name
without the extension (such as .mp3) as the track name.
Track names longer than 32 characters or four pages
are shortened. The display does not show parts of words
on the last page of text, and the extension of the
lename is not displayed.
Preprogrammed Playlists
Preprogrammed playlists which were created by
WinAmp™, MusicMatch™, or Real Jukebox™ software
can be accessed, however, there is no editing capability.
These playlists are treated as special folders containing
compressed audio song les.
Playing an MP3
Insert a CD partway into the slot, label side up.
The player pulls it in, and READING DISC displays.
The CD should begin playing and the CD symbol
displays. See “Playing a CD” earlier in this section.
3
N(Repeat):Repeat lets one track, the entire folder,
or playlist be repeated.
Press and release this button until REPEAT TRACK,
REPEAT FOLDER, or REPEAT P-LIST displays.
The current track, folder or playlist continues to repeat.
Press and release this button until REPEAT OFF displays
to turn off repeated play.4 RDM (Random):Press to hear tracks in random,
rather than sequential order. The entire folder, playlist,
or CD can be played in random order.
Press and release this pushbutton until RANDOM
FOLDER, RANDOM P-LIST (playlist), or RANDOM
DISC displays. Once all of the tracks in the current folder
or playlist have played, the system moves on to the
next folder or playlist, and plays all of the tracks
in random order.
While in random, pressing and releasing
oorpSEEK
arrow takes you to the previous or to the next random
track.
Press and release this pushbutton until RANDOM OFF
displays, to turn off random play.
5
!(Previous Folder):Press to go to the rst track in
the previous folder. Press this button while in random
folder mode to go to the previous folder and randomly
play the tracks in that folder.
6
#(Next Folder):Press to go to the rst track in the
next folder. Press this button while in random folder
mode to go to the next folder and randomly play
the tracks in that folder.
3-97

DISP (Display):Press to change between track mode,
folder/playlist mode, and ID3 tag. The display shows
only eight characters, but there can be up to four pages
of text. If there are more than eight characters in the
song, folder, or playlist name, pressing this knob within
two seconds goes to the next page of text. If there
are no other pages to be shown, pressing this button
within two seconds goes to the next display mode.
Song name and time of day mode displays
the current song name and time of day.
Folder/playlist mode displays the current folder or
playlist number the track number and the elapsed
time of the track.
Song name and track number mode displays the
current song name and track number.
ID3 Tag and folder mode displays the ID3 tag
information and the folder number.
Song and folder mode displays the number of
songs in the folder and the folder number.
INFO (Information):INFO displays when a current
track has ID3 tag information. Press this button to
display the artist name and album contained in the tag.
BAND:Press to listen to the radio when a CD is
playing. The inactive CD remains inside the radio
for future listening.
XM Radio Messages
XL (Explicit Language Channels):These
channels, or any others, can be blocked by
calling 1-800-852-XMXM (9696).
Updating:The encryption code in the receiver is being
updated, and no action is required. This process should
take no longer than 30 seconds.
No Signal:The system is functioning correctly, but the
vehicle is in a location that is blocking the XM signal.
When the vehicle is moved into an open area, the signal
should return.
Loading XM:The audio system is acquiring and
processing audio and text data. No action is needed.
This message should disappear shortly.
CH Off Air:This channel is not currently in service.
Tune in to another channel.
CH Unauth:This channel is blocked or cannot be
received with your XM Subscription package.
CH Unavail:This previously assigned channel is no
longer assigned. Tune to another station. If this station
was one of the presets, choose another station for
that preset button.
3-98

Audio System
When using the in-vehicle Bluetooth system, sound
comes through the vehicle’s front audio system speakers
and overrides the audio system. Use the audio system
volume knob, during a call, to change the volume level.
The adjusted volume level remains in memory for later
calls. To prevent missed calls, a minimum volume level
is used if the volume is turned down too low.
Bluetooth Controls
Use the buttons located on the steering wheel to
operate the in-vehicle Bluetooth system. SeeAudio
Steering Wheel Controls on page 3-110for more
information.
b>(Push To Talk):Press to answer incoming calls,
to conrm system information, and to start speech
recognition.
cx(Phone On Hook):Press to end a call, reject a
call, or to cancel an operation.
Pairing
A Bluetooth enabled cell phone must be paired to the
in-vehicle Bluetooth system rst and then connected to
the vehicle before it can be used. See the cell phone
manufacturers user guide for Bluetooth functions before
pairing the cell phone. If a Bluetooth phone is not
connected, calls will be made using OnStar
®Hands-Free
Calling, if available. Refer to the OnStar owner’s guide
for more information.
Pairing Information:
Up to ve cell phones can be paired to the in-vehicle
Bluetooth system.
The pairing process is disabled when the vehicle is
moving.
The in-vehicle Bluetooth system automatically links
with the rst available paired cell phone in the order
the phone was paired.
Only one paired cell phone can be connected to the
in-vehicle Bluetooth system at a time.
Pairing should only need to be completed once,
unless changes to the pairing information have
been made or the phone is deleted.
To link to a different paired phone, see Linking to a
Different Phone later in this section.
3-100