2009 AUDI S4 CABRIOLET wheel bolts

_______________________________________________ W_ h_ a _ t_d_ o_ l _d _o_ n_ o_ w_ ? _ __.1111
Ap plies to vehic les: with cap-covered wheel bolts
Wheels with cap-covered wheel bolts
The caps must be removed first from the wheel bolts
before the bolts can be unscrewed.
Removing
Fig . 217 Wheel
change : removing the
wheel bolt caps
- Push the plastic clip provided with the onboard tool kit
down over the wheel bolt cap until it engages.
- Pull on the properly engaged plastic clip to extract the
cap:::> fig. 217.
Refitting
- Place the caps over the wheel bolts and push them back
1n.
The caps are there to protect and keep the wheel bolts clean.•
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle.
Loosening
Fig . 218 Wheel
change : loosening the
wheel bolts
-Fit the wheel bolt wrench over the wheel bolt and push it
down as far as it will go.
- Close your grip around the end of the wrench handle for
maximum torque and turn the wheel bolts counter-clock­
wise about one single turn in the direction of arrow
:::> fig. 218 .
Tightening Fit the wheel bolt wrench over the wheel bolt and push it
down as far as it will go.
- Close your grip around the end of the wrench handle for
maximum torque and turn each wheel bolt clockwise
until it sits tight. .,
~ehicle care Do-it-yourse lf service irechnical data

11111...__W_ h_ a_ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
& WARNING
• Using force without control to speed the wheel change up can
cause the vehicle to slip off the jack and cause serious personal
injuries.
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -Risk of injury!
[ i ] Tips
• Never try and use the hexagonal socket in the handle of the
screwdriver to loosen or tighten the wheel bolts.
• If a wheel bolt sits very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one foot only . As you do, hold on to the car to keep yourself stable
and take care not to slip.•
Raising the vehicle
The vehicle must be lifted with the jock first before the
wheel con be removed.
N
"' ~ I
"' al
Fig . 219 Wheel
change : mounting
points for the lifting
jack Fig
. 220 Close-up:
proper positioning of
lifting jack
- Position the jack below the door sill under the mounting
point
that is closest to the wheel to be changed
~ fig. 219.
- Turn the
jack handle clockwise until the jack arm just fits
underneath the rib running along the underbody
~ &,.
- Align the jack so that the jack arm claw~ fig. 220 @fits
snugly around the underbody rib and the movable base
plate ® sits flat on the ground.
- Wind the jack up further until the flat wheel comes off the
ground~ &-
Recesses at the front and rear of the underbody rib mark the proper
mounting locations for the jack => fig. 219. There is only one desig­
nated jack mounting point for each wheel. Do not apply the jack
anywhere else=>& .
The jack should be positioned approximately 6 in. (15 cm) behind
the front wheel or 10 in. (25 cm) in front of the rear wheel.
An
unstable surface under the jack can cause the vehicle to slip off
the jack . Always provide a firm base for the jack on the ground. If
necessary place a sturdy board or similar support under the jack. On
hard, slippery surfaces (such as tiles) use a rubber mat or similar to
prevent the jack from slipping=>& . .,,

1111.___W_ h_ a_ t_d_ o_ l _d _o_ n_ o_ w_ ? ______________________________________________ _
-Screw the threaded end o f the alignment pin from the
tool kit hand -tight into t he now vacant bo lt hole
=>
page 297, fig . 222.
- Then completely unscrew the other wheel bolts as
described above .
- Take off the wheel leaving the alignment p in in the bolt
hole.
Puttin g on th e sp are
- Lift the spare wheel up and carefu lly s lide it over the
alignment pin to gu ide it in place .
- Use t he hexagonal socket in the screwd river handle to
screw in and tighten all w heel bolts
slightly.
- Unscrew the alignment pin and insert and tighten the
remaining w heel bolt slightly like the rest.
- Turn the handle on the jack counter-clockwise to lower
the vehicle until the jack is fully released.
- Use the wheel bo lt wrench to tighten all wheel bo lts
firmly=>
page 295. Tighten crosswise, from one bolt to
the (approx imately) oppos ite one, to keep the wheel
centered.
[ i ] Tip s
Never try and use the hexagona l socket in the handle of the screw­
driver to loosen or tighten the wheel bolts.
• Pull the reversible b lade from the screwdriver before you use the
hexagonal socket in the handle to turn the wheel bo lts.
• When mounting tires with
uni dire cti on al tread desig n make sure
the tread pattern is pointed the right way~
page 298.
• The whee l bolts should be clean and easy to turn. Check for dirt
and corrosion on the ma ting surfaces of both the wheel and the
hub. Remove all dirt from these surfaces before remounting the
wheel. •
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed the right direction.
U sin g a spa re tire wit h a tre ad p atte rn int ended for u se
i n a sp ec ific dir ection
When using a spare tire with a tread pattern intended for use in a
specific direction, please note the following:
• The direction of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction in the
event of a flat tire, use the spare tire on ly temporarily since the tire
will not be able to achieve its optimum performance characteristics
with regard to aquaplaning, noise and wear.
• We recommend that particular attention be paid to this fact
dur ing wet weather and that you adjust your speed to match road
conditions.
• Replace the flat tire with a new one and have it instal led on your
vehic le as soon as possible to restore the handling advantages of a
proper ly pointed direction-dependent tire. •
Notes on wheel change
Please read the information~ page 279, "New tires and replacing
tires and whee ls", if you are going to use a spare tire which is
different from the tires on your veh ic le.
After you change a tire: .,_

_____________________________________________ W_ h _a_t _ d_ o_ l _d _o _ n_o_ w_ ?_ . _ .... I'll
•
• Check the tire pressure on the spare immediately after
mounting.
• Have the wheel bolt t ightening torque checked with a torque
wrench as soon a s possible by your authorized Audi dealer or a
qualified se rvice station .
• On steel and alloy wheel rims , the wheel bolts are correctly tight­
ened with a torque of 90
ft lb 1120 Nm ).
• If you notice while changing a tire that the wheel bolts are
corroded and diffi cult to turn while changing a tire , they should be
replaced before you check the tightening torque .
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible . Remount the wheel cover.
Until then , drive with extra care and at reduced speeds .
& WARNING
• If you are going to equip your vehicle with tires or r ims which
differ from those which were factory installed , then be sure to read
the information
~ page 279 , "New tires and replacing tires and
wheels ".
• Always make sure the damaged wheel or even a flat tire and
the jack and tool kit are properly secured in the luggage compart ­
ment and are not loose in the passenger compartment .
• In an accident or sudden maneuver they could fly forward ,
injur ing anyone in the vehicle .
• Always store damaged wheel , jack and tools securely in
luggage compartment . Otherwise , in an accident or sudden
maneuver they could fly forward, causing injury to passengers in
the vehicle .
0 Note
Do not use commercially availab le ti re sealants. Otherw ise, the elec ­
t rica l compo nents of t he tir e pressure mon itor ing sys te m * w ill no longer work properly and the sensor for
the tire pressure moni ­
t o ring syste m will have to be re placed by a q ual ified work shop.•
Do-it-yourself service

11111 Alphabetical index
---=----------------------------------
Speed warning 1 ...... .... ... ... .... . 34
Speed warning 2 .................. ... 34
Speed warning system ............... 35
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 15
Startingtheengine . ...... ...... 119,120
What should I do if the engine does not
start? . . . . . . . . . . . . . . . . . . . . . . . . . 120
Steel wheels . . . . . . . . . . . . . . . . . . . . . . . 236
Steering ...... ............... ... ... 118
Steering wheel Locking the steering .............. 119
Steering wheel column Adjusting ... .. .... .... ...... .... 118
Steps for determining correct load limit 276
Stopping the engine .. ....... ....... 120
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Compartment in the front seats .... 109
Compartments in the door trims ... 109
Cupholder in the center conso le .... 104
Glove compartment ... .... ...... . 107
Ski sack . . . . . . . . . . . . . . . . . . . . . . . . 103
Small objects .. .... ....... .... ... 108
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Switches Emergency flasher . . . . . . . . . . . . . . . . 82
Rear window defogger . . . . . . . . . . . . 116
Symbols Red ............................. 30
Yellow ........................... 32
T
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 13 Tank
flap
Unlocking the fuel filler flap by hand 248
Technical modifications ... ...... ... .. 319
Temperature Climate controls ...... .... ....... 112
Setting for the driver's and front passen­
ger side . . . . . . . . . . . . . . . . . . . . . . . 112
The first 1,000 miles (1,500 km) and
afterwards ... ... .... ...... ..... 219
Tilt sensors . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tips for the environment
Using the air conditioner only when
necessary . . . . . . . . . . . . . . . . . . . . . 116
tiptronic® . . . . . . . . . . . . . . . . . . . . . . . . . 126
Automatic Shift Lock (ASU ...... ... 128
Driving ...... .... ... .. .... .... .. 126
Dynamic shift program ....... .. ... 129
Fail -safe mode . . . . . . . . . . . . . . . . . . . 131
Kick-down . . . . . . . . . . . . . . . . . . . . . . . 129
Manual shift program ............ . 130
Selector lever . . . . . . . . . . . . . . . . . . . . 127
Tire pressure ... .......... .......... 274
Tire pressure monitoring system ... .... 41
Initialize wheels ................... 45
learning process ........... ....... 43
loss of air pressure .. .... ... .. . 20, 43
Malfunctions . .... ....... ..... ... . 46
Sensors . . . . . . . . . . . . . . . . . . . . . . . . 281
Storing tire pressures ...... ...... .. 43
Tires and wheels ....... .... ...... 281
Valves .......................... 281
Tire service life ... ...... .... ... .. ... 278 Tires
... .. .... .... .. . ... ... .... ... . 267
Replacing .. .... ....... .... ...... 281
Service life ...................... 278
speed rat ing letter code .... .... ... 281
Tire manufactur ing date ........... 281
Tire spec ifications ................ 280
Tread depth .... .... ........ .... . 278
Uniform tire quality grading ... .... 283
Winter tires .. ...... ......... .... 284
Tires and vehicle load limits ..... ..... 275
Tires and wheels Checking tire pressure .......... .. 274
Cold tire inflation pressure ........ 271
Dimensions .... .... ..... ...... .. 279
General notes ......... ... ...... .. 267
Glossary of tire and loading terminology .
268
New tires and whee ls ............. 279
Replacing .. .... ....... .......... 280
Snow chains .. .... .... ........ ... 285
Tire pressure monitoring system ... 281
Tires and vehicle load limits ....... 275
Wheel bolts ........ ....... .... .. 286
Winter tires
Tires/Wheels 284
Low aspect ratio tires ............. 286
Tir e pressure monitoring system .... 20
Torn or frayed safety belts ... .. .... ... 162
Touch-up paint
Towing Front eyelet 235
307
Rear eyelet .... ........ ..... .. ... 307
Tow truck procedures ...... ....... 306

Alph ab eti ca l ind ex -____________ _,_ __ _
Trailer towing .. ... .... ..... .. .. ... . 224
Operating instructions ....... .... . 225
Technical requirements ....... 224 , 225
Trailer tow ing tips ................ 226
Transmission tiptronic® .... ... ... ..... .... .... 126
Transport Canada ... .... .... ...... .. 155
Tread Wear Indicator
(TWll ........... 278
Trip computer Fuel consumption .... .... ... .... .. 37
Mileage .. .... ..... .. .... ...... ... 37
Trip odometer . ...... .... ...... .... .. 15
What does it mean when dEF appears in
the trip odometer display? ......... 15
Trunk Escape handle .. .... .... ......... 290
Trunk lid
See Rear lid .... .. .... ...... .... ... 55
Turn signals . .............. .......... 83
Warning/indicator lights ... ......... 21
u
Undercoating ..... .. .... .... ... .... . 237
Unfastening safety belts ... .... .... .. 165
Unidirectiona l tires ...... ...... .... .. 267
Uniform tire quality grading .. ..... ... 283
Universal Remote Control (Homelink®l . 139
Unlocking Power locking switch .............. 54
Rear lid . ... .. .... .... ...... ...... 55
Remote control .. .. .... .... .... ... 51
Using the key . ... .. .. .... ...... ... 53
Controls and equip­
ment Safety first
V
Vanity
mirror .... ..... ........ ..... .. 84
Vehicle electrical system ....... .... ... 22
Vehicle Identification !Number (VIN) .... 312
Vehicle jack .................... 290, 296
Vehic le literature .. .... ... .. ...... ... .. 5
Vehicle -care products .... .... .... .... 230
w
Warning lights ....................... 18
Warning/indicator lights .... .... ....... 12
Airbag system ............ .... .... 20
Anti-lock brake system (ABS) ... ..... 20
Brake system ....... .... .... ..... . 23
Cruise control .... ... .... .... .... .. 20
Electronic power control ............ 22
Electron ic stabil ization program (ESP) 22
Generator .. ........ .... ... .. .... . 22
High beam . .... ........... .... ... 22
Malfunction lndica11:or Lamp (Mill . ... 19
Parking brake ...... .... ....... .... 23
Power top .... ...... .... .... . ... .. 21
Safety belt ... ....... .. .. .... .... .. 21
Tire pressure monitoring system ..... 20
Turn signals .. ..... .. .... .... .... . 21
Warranty coverages ........... .... .. 316
Washing ..................... ...... 230
Automatic car wash ... ...... .... .. 231
by hand ......................... 231
Power top cleaning ......... ..... . 233
w ith a power washer .............. 232 Washing
the vehicle .... .... ... .. .. .. 230
Waxing .... .... .... ... .. ...... .... . 233
Wear indicator ...................... 278
Weatherstrips .... ... .... .... .... ... 236
Weights .... .... ... .. .... ...... ..... 313
What happens if you wear your safety belt too
loose? . .... .... ... .. ...... .... . 164
What happens to unbelted occupants? . 161
What impairs driving safety? .......... 147
What should I do after changing a wheel? . .
275
What should I do after replacing whee ls?
275
Wheel bolts Torque ..... .... .... .... .... ..... 286
Wheel change .... .... ... .... .... ... 293
Wheels .. .. .. .......... ....... ..... 267
Cast a lloy ..... ... ..... ...... ... .. 237
Checking tire pressure ............ 274
Cold tire inflation pressure . .... .... 271
Genera l notes .. .... ... .... .... ... 267
G lossary of t ire and loading terminology
268
New tires and wheels ........ .... . 279
Rim ............................ 267
Steel whee ls ..................... 236
Tires and vehicle load limits ........ 275
When must a safety belt be replaced? .. 162
When must the airbag system be inspected? 179
When should I adjust the tire pressures? ...
275
When should I check the tire pressures? 275
Vehicle operation Vehicle care Do-it-yourself service Technical data