2009 AUDI S3 spare tire

What do I do now? -__________________ __;__:....:....:..:: __ _
•
-All passengers should leave the car and move to a safe
location (for instance, behind the guardrail)~& .
- Apply the
parking brake firmly ~& .
- Move
selector lever to position Pon an automatic trans-
miss ion; put manual transmission in
first gear ~& .
-If you are towing a trailer : unhitch the trailer from your
vehicle.
- Take the
tool and the spare tire~ page 270 out of the
luggage compartment.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flasher on and use other warning
devices to alert other motorists.
• Make sure that passengers wait
in a safe place away from the
vehicle and well away from the roadway and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed. When one
front wheel is lifted off the ground, placing the automatic trans­
mission in "P" (Park), or engaging a gear in a manual transmission
will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the spare wheel, make sure that you remount
the flat tire/wheel in its storage area properly and tighten the
knurled retaining screw securely. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and exactly in that order.
1. Remove the decorative wheel cover*. For more details
see also
~ page 274, "Decorative wheel covers" or
~ page 275, "Wheels with cap-covered wheel bolts".
2. Loosen the
wheel bolts ~ page 276.
3. Locate the proper mounting point for the jack and align the jack below that point~
page 276.
4. Lift the car with the jack~ page 276.
5. Take the flat wheel off and then put the spare on
~ page 278.
6. Tighten all wheel bolts lightly .
7.
Lower the vehicle with the jack .
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts
~ page 276.
9. Put the decorative wheel cover* back on.
& WARNING
Always read and head all WARNINGS and information ::} & in
"Raising the vehicle" on
page 276 and ~ page 279. •
After changing a wheel
A wheel change is not complete without the following
actions.
- Store and secure the replaced wheel in the spare wheel
well. .,._
Do-it-yourself service

llffl.___W_ h_ a_t _d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
- Put the tool case and the jack back in p lace in the luggage
compartment.
- Check the tire pre ssure on the spare whee l immediately
after mounting it.
- As soon as possible, have the tightening torque s on all
wheel bo lts checked with a torque wrench . The correct
tightening torque is 90 ft lb (120 Nm) .
- Have the flat tire replaced as soon as possible.
[ i ] Tip s
• If you notice while changing a tire that the wheel bolts are
corroded and difficult to turn, then they should be replaced before
you check the tightening torque .
• Drive at reduced speed until you have the tightening to rques
checked .a
Ap plies to ve hicles: w it h full whee l co vers
Full wheel covers
The wheel covers must be removed to access the wheel
bolts.
Remo va l
- Pull the full wheel cov er off manually.
Inst alla tion
- First press the full wheel cove r onto the rim at the cut -out
prov ided for the valve. Then engage the outer edge of the
f ull whe el cover in the steel rim. •
Applies to vehi cles : w it h deco ra tiv e wh eel co vers
Decorative wheel covers
The decorative wheel covers must be removed first to
access the wheel bolts .
Removing
Fig. 19 1 Whee l
ch ange : remov in g th e
w hee l cover
- Inse rt the hook provid ed with the onboard tool kit into
t h e hole on the cen ter hub piece .
- P ull off the decorative wheel cover => fig . 19 1. •

11111...__W_ h_ a _ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
Taking the wheel off /putt ing the spare on
Follow these instructions step-by-step for changing the
wheel
M
"' ;;; u.
1li
Fig . 197 Wheel
change : using the
screwdriver handle
(with the blade
removed) to turn the
bolts
Fig . 198 Wheel
change: alignment pin
inside the top hole
After you have loosened all wheel bolts and jacked the
vehicle off the ground, perform the following steps to
remove and replace the wheel:
Removing the wheel
- Use the hexagonal socket in the screwdriver handle to
completely turn out the topmost wheel bolt and set it
as ide on a
clean surface ~ fig. 197. - Screw the threaded end of the
alignment pin from the
tool kit hand-tight into the now vacant bolt hole
~ fig. 198.
- Then completely unscrew the other wheel bolts as
described above.
Take off the wheel leaving the alignment pin in the bolt
hole.
Putting on the spare
- Lift the spare wheel up and carefully slide it over the
alignment pin to guide it in place.
- Use the hexagonal socket in the screwdriver handle to
screw in and tighten all wheel bolts
slightly.
Unscrew the alignment pin and insert and tighten the
remaining wheel bolt slightly like the rest.
- Turn the handle on the jack counter -clockwise to lower
the vehicle until the jack is fully released.
- Use the wheel bolt wrench to tighten all wheel bolts firmly ~
page 276. Tighten them crosswise , from one
bolt to the (approximately) opposite one, to keep the
wheel centered.
[ i ] Tips
Never try and use the hexagonal socket in the handle of the screw­
driver to loosen or tighten the wheel bolts.
• Pull the reversible blade from the screwdriver before you use the
hexagonal socket in the handle to turn the wheel bolts.
• When mounting tires with
unidirectional tread design make sure
the tread pattern is pointed the right way=>
page 279. ~

_______________________________________________ W_ h_ a_t _ d_ o_ l _d _o_ n_ o _ w_ ? __ ffllll
•
• T he wheel bolts should be clean and easy to turn . Check for dirt
and corrosion on the mating surfaces of bo th the wheel and the
hub. Remove all dirt from these surfaces before remounting the
whee l.•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed in the right direction.
Using a spar e tir e with a tread pa ttern intended for u se
in a sp ecific direc tion
When using a spare tire with a tread pattern intended for use in a
specific direction , p lease note the following:
• T he direction of rotation is marked by an arrow on the sid e of the
tire .
• I f the spare tire has to be installed in the incorrec t direction in the
event of a flat tire , use the spare tire on ly temporarily since the tire
wi ll not be ab le to achieve its optimum performance characteristics
with regard to aquap laning, noise and wear .
• We recommend that particula r atten tion be pa id to this fact
dur ing wet weather and that you adjust your speed to match road
conditions.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible to restore the handling advantages of a p roper ly pointed d irection -dependent t ire. •
Notes on wheel change
Please read the information=> page 255, "New tires and replacing
tires and wheels" if you are going to use a spare tire which is
different from the tires on your veh ic le.
Aft er you change a tire :
• Che ck the ti re pre ss ure on the spare immed iately aft er
mounting .
• Have the wheel b olt t ight en ing to rque checked with a torque
wrench a s soon a s po ssible by your authorized Audi dea ler or a
q u alified service stat ion .
• On steel and a lloy wheel rims , the wheel bolt s are correctly tight­
ened with a t orque of 90 ft lb (1 2 0 Nm l.
• If you noti ce w hile changing a tire that the wheel bolt s are
c o rroded and d iff ic ult to turn , then they should be repla ced befo re
you check the tightening torque.
• Repl ace the fl at t ir e w ith a new one and hav e it installed o n your
vehicle as soon as pos sib le . Remount the wheel cover .
Until then , drive wi th ext ra care and at redu ced speeds.
& WARNING
• If you are going to equip your v ehi cle wi th tire s or rim s wh ich
diffe r from tho se which were fa ctory installed , th en be sure to r ead
the infor mation
=> page 255, " New tires and repl acing tire s and
wheel s".
• Alway s ma ke sure the d amag ed w heel or e ven a flat t ire and
the jack and tool kit ar e properly secured in the lugg age comp art­
ment and are not loose in the p asse nger co m partment .
• In an a ccident o r sudden maneu ver th ey could fl y fo rw ard ,
injur ing anyo ne in th e vehi cle .
• Alway s store damaged wheel , ja ck and tool s se curel y in
luggag e compartment . Oth erwi se, in an accid ent or sudd en
m aneuv er the y could fly fo rward, c au sing in jur y to pa ssenge rs in
the vehic le . •
Do-it-yourself service

___ A_ l..:,. p _ h_ a_ b_e _t_ic _ a_l _in _ d_e_ x ____________________________________________ _
Setting
Date display . .... ... ... .. ... ... .... 9
Digital clock ........... .... ..... ...
9
Side airbags
Description ... .... .... ... .... ... 163
How they work . . . . . . . . . . . . . . . . . . . 164
Side curtain airbags ...... ....... .... 166
Description . ...... .... .......... 166
How they work . . . . . . . . . . . . . . . . . . . 167
Safety instructions . . . . . . . . . . . . . . . 168
Sk i sack ..................... ....... 87
Snow chains . . . . . . . . . . . . . . . . . . . . . . . 261
Sockets ............. .... .... ... .... 93
Sound system Replacing . .... .... .... ... .... ... 306
Sound system display .... .... .... .... 18
Spare tire . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Spare wheel
See Spa re tire . . . . . . . . . . . . . . . . . . . 271
Speed rating letter code . . . . . . . . . . . . . 257
Speed warning ... .... .... ... .... .... 33
Speed warning system ...... .... .... . 26
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 10
Star ting assistance
4-cylinder engine
6 -cylinder engine
Star ting on hi lls 289
290
Hill hold assis t ........ ....... .... 111
Starting the engine ....... .... .. 108, 109
What should I do if the engine does not
start? . . . . . . . . . . . . . . . . . . . . . . . . . 109
St ee l whe els . . . . . . . . . . . . . . . . . . . . . . . 21 1 Steering
. . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Locking the steering . . . . . . . . . . . . . . 108
See also Electro-mechanical power assis t
16, 195
Steering wheel column Adjusting ..... ... ..... .... .... .. 107
St eps for d eter mining correc t load limit 252
Stopping the engine ................. 109
Storage . .... .... ..... .. .... ..... ... 94
Compartments in the door tr ims .. ... 96
Cup holder rear center armrest ...... 92
G love compartment . ...... .... .... 95
Small objects .......... ....... .... 95
Storage compartment Increasing size ....... .... ... .. .... 83
Sun blind .. ...... .. .. .... .... .... 62, 63
Sun visors .. ...... ....... .... .... ... 62
Sunroof
See panoramic sli din g sunroof ...... 48
Switches Emergency flasher . . . . . . . . . . . . . . . . 58
Switching the air cond itioner (automatic)
on/off ... . ..... ................. 100
Symbols
T
Red symbols in the center display ... 28
Ye llow symbols in the center display . 29
Tachometer .. .... ...... .... ... .. .... . 8
Tailgate
See Rea r lid ... ... .... .... .... .... 42
Technical modifications .. ............ 306 Temperature
Clima te controls .. .... ...... ... .. 101
Setting for the drive r's and front passen-
ger's side ..... ....... ...... .... 101
Tether strap .. .... .... ... .... .... ... 187
Securing the upper tether strap .... 188
The first 1,000 mil es (1,500 km) and
afterwards .... .. .... .... .... ... 197
Tie-downs . . . . . . . . . . . . . . . . . . . . . . 84 , 135
Tips for the environment
Saving fuel .. ...... .... .. .. .... ... 91
Tire pressure ...... .... ......... .... 250
Tire pressure monitoring system ...... 264
Changing wheels ............ ..... 267
Declaration of conformity . ........ 268
Learning process ... .... ...... .... 266
Loss of air pressure . .... ... .. .. 13,265
Malfunctions ... .. .... .... .... .. . 267
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . 257
Storing tire pressures .......... .. . 266
Tires and wheels .. ... .. .. .. ..... . 257
Valves ...... ...... .... ...... .... 257
Warning light ... .. .... .... .... .... 34
Tire service life .... .... ... ..... ... .. 254
Tires ........... ..... ....... ....... 243
Replacing . .... .... .... ...... 255, 257
Service life ...... .... .... .... .... 254
speed rating letter code ... .... .... 257
Tire manufacturing date .... .... ... 257
Tire specif ications ........ .. .... .. 256
Tread depth .. .......... .... ..... 254
Un iform tire quality grading ... .... 259
Winter tires .. ....... .. .. .. .... .. 260