2009 Alfa Romeo MiTo wheel bolts

164IN AN EMERGENCY
❍for versions with steel wheels: insert the screwdriver into open-
ing A-fig. 4 to release clip B retaining the hub cap.
❍use wrench A-fig. 5 to loosen the retaining bolts by one turn;
❍for versions with alloy wheels: rock the vehicle to facilitate the
detachment of the rim from the wheel hub. Some versions
may be fitted with alloy wheels with a hub cap (fig. 6). To
remove the hub cap insert the screwdriver into housings
A-fig. 6 in order to access the retaining bolts. Replace the wheel
as described previously.
fig. 4A0J0236mfig. 6A0J0238m
fig. 5A0J0106m
159-196 Alfa MiTo GB 12-11-2008 15:45 Pagina 164

IN AN EMERGENCY165
4
❍operate device A-fig. 7 to extend the jack, until the upper part
B-fig. 8 inserts correctly into device C;
❍warn anybody nearby that the car is about to be lifted. They
must stay clear and not touch the car until it is back on the
ground;
❍insert handle D-fig. 7 into the housing on device A, operate the
jack and lift the vehicle until the wheel is several centimetres
off the ground;
❍make sure that the contact surfaces on the small spare wheel
are clean and free of impurities which may subsequently cause
the retaining bolts to loosen;
❍fit the small spare wheel by inserting the first bolt for two
threads into the hole closest to the inflation valve;
❍use wrench A-fig. 5 to fully tighten the retaining bolts;
❍operate jack handle D-fig. 7 to lower the vehicle. Remove the
jack;
fig. 7A0J0062mfig. 8A0J0061m
159-196 Alfa MiTo GB 12-11-2008 15:45 Pagina 165

166IN AN EMERGENCY
fig. 9A0J0271mfig. 10A0J0180m
❍use wrench A-fig. 5, to fully tighten the retaining bolts, tight-
ening first one bolt and then the diametrically opposite bolt,
following the sequence shown in fig. 9;
❍when replacing an alloy wheel it is advisable to place it upside
down, with the aesthetic part facing upwards.
REMOVING THE SUBWOOFER (versions with
HI-FI bose system, where provided)
IMPORTANT The following procedure only applies to vehicles
equipped with Bose Hi-Fi systems with Subwoofer (where provid-
ed).
On these versions the tools for replacing the wheel are found in a
dedicated bag in the luggage compartment.
Subwoofer and small spare wheel
Proceed as follows to remove the Subwoofer:
❍open the luggage compartment, pull tab A-fig. 2 and lift up the
mat;
❍undo locking device A-fig. 10 and lift up the Subwoofer. Then re-
move connection cable B from Velcro attachment C;
159-196 Alfa MiTo GB 12-11-2008 15:45 Pagina 166

168IN AN EMERGENCY
REFITTING THE WHEEL
Following the procedure described previously, raise the car and re-
move the small spare wheel.
Proceed as follows:
❍make sure the contact surfaces between spare wheel and hub
are clean so that the fastening bolts will not come loose;
❍tighten the retaining bolts using wrench A-fig. 4;
❍lower the car and remove the jack;
❍use wrench A-fig. 4 to fully tighten the bolts, following the se-
quence shown in fig. 9;
❍for versions with steel rims: secure the wheel hub to the rim;
❍for versions with alloy rims with hub cap: align the pin on the
cap with the seat on the rim.
After tyre replacement:stow the small spare wheel in
the space provided in the boot; place the jack and other tools
into their container; place the container, complete with tools on
the small spare wheel; replace the luggage compartment mat.
159-196 Alfa MiTo GB 12-11-2008 15:45 Pagina 168