2009 Alfa Romeo GT spare wheel

GETTING TO KNOW YOUR CAR
135
Always take due care when braking on
bends, even with the help of the ABS.
The most important advice of all, howev-
er, is this:
When the ABS cuts in, and
you feel the pulsing on the
pedal, do not lighten the
pressure, but keep the pedal firm-
ly pressed with no fear; this way
you will stop in the least space
possible, compatibly with the con-
ditions of the road surface.
Following these instructions you will be
in the best braking condition under all cir-
cumstances.
IMPORTANTCars fitted with ABS may
only be fitted with the wheel rims, tyres and
brake linings of type and brand approved by
the Manufacturer.
The system is completed by the EBD (Elec-
tronic Brake Distributor) which distributes
the braking action through the control unit
and the ABS system sensors. The car is fitted with an
electronic braking distribu-
tor (EBD). If the
>andx
warning lights turn on simultane-
ously with the engine running, this
indicates an EBD system failure; in
this case with sharp braking the
rear wheels might lock too early,
with the possibility of skidding. Dri-
ving extremely carefully, go to the
nearest Alfa Romeo Authorised Ser-
vice to have the system checked.
The turning on of only the
>warning light with the
engine running normally in-
dicates a fault to the ABS system
only. In this case the braking sys-
tem is still efficient, though with-
out the aid of the anti-lock device.
Under these conditions perfor-
mance of the EBD system may be
reduced. In this case too, you are
advised to go immediately to the
nearest Alfa Romeo Authorised
Service to have the system checked
over, driving in such a way as to
avoid sharp braking.
If the low brake fluid lev-
el
xwarning light turns
on, stop the car immedi-
ately and contact the nearest Alfa
Romeo Authorised Service. Any
loss of fluid from the hydraulic sys-
tem will negatively affect the op-
eration of the braking system be it
of the conventional type or of the
type with ABS.
If the compact spare
wheel is used, operation of
the ABS system is cut off
and the
>warning light on the in-
strument cluster turns on.
IMPORTANTIf the battery is run down
the
>andxwarning lights might turn on
when starting the engine and go off after
starting. This should not be considered as
a fault but as a warning that during start-
ing the ABS is not active. The turning off
of the warning lights ensures normal system
operation.

GETTING TO KNOW YOUR CAR
137
The stabilising action of the system is
based on the calculations of the system elec-
tronic control unit, which processes the sig-
nals received from the steering wheel rota-
tion sensor, acceleration sensor and rotation
speed sensor of each wheel. These signals
allow the control unit to recognise the ma-
noeuvre the driver intends to do when the
steering wheel is turned.
The control unit processes the information
received from the sensors and therefore is
able to know the position of the car instant
by instant and compares it with the course
the driver would like to follow. In the event
of a discrepancy, in a fraction of a second
the control unit chooses and commands the
most suitable intervention to bring the car
immediately back to the required course:
braking one or more wheels at different in-
tensity and, if necessary, reducing the pow-
er transmitted by the engine.
The corrective actions are modified and
controlled continuously in seeking the course
required by the driver.
The action of system considerably en-
hances the active safety of the car in very
critical situations and it is particularly help-
ful when the grip conditions of the road sur-
face change. For the VDC system to
work correctly, the tyres
must be of the same brand
and type on all wheels, in perfect
conditions and above all of the
specified type, brand and size. CUTTING IN
OF THE VDC SYSTEM
The cutting in of the system is indicated by
the flashing of the áwarning light on the
instrument cluster, to inform the driver that
the car is in critical conditions of stability and
grip.
VDC system failure warning
In the event of a failure the system dis-
engages automatically and the
áwarning
light on the instrument cluster turns on glow-
ing steadily, together with the message on
the reconfigurable multifunction display.
In the event of an system failure the car
behaves like a car not fitted with this sys-
tem: in any case it is advisable to contact
Alfa Romeo Authorised Services as soon as
possible.During use of the compact
spare wheel, the VDC sys-
tem continues working. It
should be borne in mind that the
spare wheel is smaller than a nor-
mal tyre, therefore its grip is low-
er than that of the other tyres of
the car.

GETTING TO KNOW YOUR CAR
139
ASR system
failure indications
In the event of a fault, the ASR system
switches off automatically and the
Vwarn-
ing light on the instrument cluster turns on,
together with the message on the reconfig-
urable multifunction display.
In the event of an ASR system operating
failure, the car behaves in the same way
as a car that is not fitted with this system:
in any case, it is advisable to contact Alfa
Romeo Authorised Services as soon as pos-
sible.MSR SYSTEM (engine braking
torque control)
The car is fitted with a special system, in-
tegral with the ASR system, that in case of
sudden gear shifting, cuts in providing torque
to the engine thus preventing excessive dri-
ving wheel drive that, specially in poor grip
conditions, can lead to loss of stability. During use of the compact
spare wheel, the ASR func-
tion is cut off and the
V
warning light on the instrument
cluster turns on glowing steadily
together with the message on the
reconfigurable multifunction dis-
play.
For correct operation of
the ASR system, the tyres
must absolutely be of the
same brand and type on all wheels,
in perfect conditions and, above all,
of type, brand and size specified.
IMPORTANTWhen travelling on snowy
roads with snow chains, it may be helpful
to turn the ASR off: in fact, in these condi-
tions, slipping of the driving wheels when
moving off makes it possible to obtain bet-
ter drive.

CORRECT USE OF THE CAR
178
Keep your speed
down when snow
chains are fitted.
Do not exceed 50 km/h. Avoid
potholes, steps and pavements and
avoid also to drive for long dis-
tances on roads not covered with
snow to prevent damaging the car
and the roadbed.
CAR INACTIVITY
If the car is to be left inactive for long pe-
riods, the following precautions should be
noted:
– House the car under cover in a dry and
possibly ventilated place.
– Engage a gear.
– Check that the handbrake is not en-
gaged.
– Clean and protect the paintwork by pro-
tective wax.
– Clean and protect the metal polished
parts with marketed products.
– Cover the rubber windscreen and
rearscreen wiper blades with talcum powder
and raise them off the glass.
– Open the windows slightly.
– Inflate the tyres to a pressure of 0.5 bars
above normal. If possible rest the tyres on
wooden planks and periodically check the
pressure.
– Do not turn on the electronic alarm sys-
tem.– Disconnect the battery negative termi-
nal from the battery and check the battery
charge. This check should be repeated
every three months during stowage.
Charge the battery if the indicator (where
provided) shows a dark colour in the central
green area.
– Do not empty the engine cooling sys-
tem.
– Cover the car with a fabric or perforat-
ed plastic cover. Do not use compact plas-
tic covers which prevent the humidity on the
surface of the car from evaporating. Snow chains cannot be
fitted to the space-saver
spare wheel. So, if a front
(drive) wheel is punctured and
chains are needed, a rear wheel
should be fitted to the front of the
car (adjust tyre pressure to the
specified value as soon as possi-
ble) and the space-saver spare
wheel should be fitted to the rear.
This way with two normal drive
wheels, snow chains can be fitted
to them to solve an emergency.
Deactivate the ASR sys-
tem when snow chains are
fitted. Press the ASR-OFF
button, button led turned on.

IN AN EMERGENCY
181
STARTING BY INERTIA
If the car is equipped with “Kit for tyre re-
pair Fix&Go“, see the instructions contained
in the following chapter.
GENERAL INSTRUCTIONS
As an alternative to the FIX & GO, the car
can be provided (upon request) with space-
saver spare wheel or standard wheel; wheel
changing and correct use of the jack call for
some precautions as listed below.
IN THE EVENT OF A PUNCTURE
Never push, tow or coast
start the car. This could
cause fuel to flow into the
catalyst damaging it irreversibly.
Remember that the en-
gine brake and power
steering are not opera-
tional until the engine is started,
therefore, much greater effort than
usual is needed on the brake ped-
al and steering wheel.
Signal the presence of the
stationary car according to
current regulations: hazard
warning lights, reflecting triangle
etc.. Any passengers should leave
the car and wait for the wheel to be
changed out of harm of the traffic.
If parked on a slope or rough sur-
face, chock the wheels with
wedges or other suitable devices
to prevent the car from rolling.
Never start the engine
with the car jacked.
When driving with a trail-
er, disconnect the trailer before
raising the car. The compact spare
wheel is specific to your car, do not
use it on other models, or use the
spare wheel of other models on
your car.
Should the type of wheels used
be changed (alloy rims instead of
steel), it is also necessary to
change the whole set of fastening
bolts with others of suitable size.
The compact spare wheel is nar-
rower than normal wheels, it
should be used only for the dis-
tance necessary to reach a service
point to have the punctured tyre
repaired and, during its use, the car
speed must not exceed 80 km/h.

IN AN EMERGENCY
182
The spare wheel has a
sticker that summarises
the main cautions for use
and limitations. The sticker should
never be removed or covered. The
sticker contains the following in
four languages:
CAUTION! FOR TEMPORARY USE
ONLY! MAX 80 km/h! REPLACE BY
NORMAL WHEEL AS SOON AS
POSSIBLE. DO NOT COVER THIS
LABEL IN USE.
Never fit a wheel cap on a com-
pact spare wheel.
The car will handle differently
with the spare wheel fitted: avoid
heavy braking and accelerating,
sharp corners and fast bends.The life of the spare
wheel is approx. 3000 km,
after this distance it should
be replaced with another of the
same type.
Never attempt to fit a conven-
tional tyre on a rim designed for
use as a compact spare wheel.
Have the punctured wheel repaired
and refitted as soon as possible.
Two or more compact spare
wheels should never be used to-
gether.
Do not grease the threads of bolts
before installing them; they might
slip out.
The jack only serves for chang-
ing wheels on the car with which it
is provided or on cars of the same
model. It must not be used for oth-
er purposes such as for instance
raising cars of other models. In no
case should it be used for repairs
under the car.
Incorrect positioning of the jack
may cause the jacked car to fall.
Do not use the jack for higher ca-
pacities than stated on its label.Snow chains cannot be
fitted on the compact spare
wheel, so, if a front wheel
is punctured and chains need to be
used, the front axle should be fit-
ted with normal wheels and the
compact spare wheel fitted to the
rear. This way, with two normal
wheels at the front, snow chains
can be fitted thereby solving the
emergency situation.
Never tamper with the inflation
valve.
Do not insert tools of any kind be-
tween the rim and the tyre.
Check, and if necessary, restore
the pressure of the tyres and of the
compact spare wheel to the values
given in the “Technical Specifica-
tions” chapter.

IN AN EMERGENCY
183
CHANGING A WHEEL
Please be informed that:
– the jack mass is 2.100 kg.
– the jack requires no adjustment.
– the jack cannot be repaired. In the event
of breakage, it must be replaced by anoth-
er original one.
– no tools other than its operating crank
can be fitted to the jack.
To change a wheel, proceed as follows:– Stop the car in such a position that it is
not dangerous for the traffic, where it is pos-
sible to change the wheel safely. Where pos-
sible, park on a level, compact surface.
– Switch off the engine and engage the
handbrake.
– Engage first gear or reverse.– Use handle(A-fig.2) to remove the
stiff covering (B).
– Loosen the clamping device (A-fig. 3).
– Take out the tool container (B) and take
it near the wheel to be changed.
– Take the spare wheel (C).
– Remove the wheel cap (A-fig. 4) (on-
ly versions with steel rims)
fig. 2
A0A0645b
fig. 3
A0A0151b
fig. 4
A0A0154b

IN AN EMERGENCY
184
– Using the wrench provided (A-fig. 5),
loosen the fastening bolts by about one turn.
– Set the jack under the car, near the
wheel to be changed taking care not to dam-
age the plastic streamlined guard.
– Work the jack crank (A-fig. 6), to ex-
tend it until the groove (B) on the upper
part of jack is correctly inserted on the low-
er profile of the body (C) approx. 40 cm
from the profile of the wheelhouse.
– Work the jack and raise the car until the
wheel is a few centimetres from the ground.
– Completely unscrew the fastening bolts
and remove the wheel.– Make sure that the contact surfaces of
the spare wheel with the hub are clean and
free of impurities which may later cause the
fastening bolts to slacken.
– Install the spare wheel matching the
hole (A-fig. 7) with the corresponding pin
(B).
– Using the wrench provided, fasten the
five bolts.
– Lower the car and remove the jack.
– Using the wrench provided, fully tighten
the bolts in the sequence shown in fig. 8.REFITTING
A NORMAL WHEEL
– Following the procedure described pre-
viously, raise the car and remove the spare
wheel.
For versions with steel rims:
– Fit the normal wheel matching the hole
(A-fig. 7) with the corresponding pin (B).
– Make sure that the contact surfaces of
the wheel with the hub are clean and free
of impurities which may later cause the fas-
tening bolts to slacken.
fig. 5
A0A0694b
fig. 6
A0A0695b