2009 Alfa Romeo GT reset

GETTING TO KNOW YOUR CAR
27
After adjustment, always
check that the slider is an-
chored in one of the posi-
tions provided. To do this, with the
button (A) released, exert a fur-
ther pressure to allow the anchor
device to catch if release did not
take place at one of the preset po-
sitions.
Never press button (C)
when travelling. To unfasten the seat belts:press
button (C-fig. 35). Guide the seat belt
with your hand while it is rewinding, to pre-
vent it from twisting. Through the reel, the
belt automatically adapts to the body of the
passenger wearing it, allowing freedom of
movement.
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the web-
bing coming out when it is jerked or if the
car brakes sharply, in a collision or when cor-
nering at high speed.
Always adjust the seat
belt height when the car is
stationary. FRONT SEAT BELT HEIGHT
ADJUSTMENT
Always adjust the height of the belts adapt-
ing it to the person who is wearing it. This
precaution improves their effectiveness sub-
stantially reducing the risk of injury in the
event of a crash.
Correct adjustment is obtained when the
belt passes half way between the end of the
shoulder and the neck.
The front seat belt ring can take 4 differ-
ent positions which make it possible to ad-
just the height of the belts.
To adjust, press button (A-fig. 36) and
lower or raise the grip (B).
fig. 36
A0A0685b

GETTING TO KNOW YOUR CAR
36
Below is a summary of the rules
of safety to be followed for car-
rying children:
– The recommended position for installing
a child’s seat is on the rear seat, as it is the
most protected in the event of a crash.
– If the passenger’s air bag is deactivated
alwayscheck warning light
Fon the
cluster to make sure that it has actually been
deactivated.
– Carefully follow the instructions provid-
ed with the child’s seat, which the supplier
is obliged to attach. Keep them in the car
together with the documents and this book-
let. Do not use used seats without the in-
structions for use.
– Always pull the tape to check that belts
are buckled.
Never place cradle child’s
seats facing backwards on
the front passenger seat of
cars fitted with passenger’s air bag
since the air bag activation could
cause serious injuries, even mortal.
You are advised to carry children
always on the rear seat, as this is
the most protected position in the
case of a crash.– All restraint systems are strictly for one
child only: never use for two children at the
same time.
– Always make sure that the belts do not
rest on the child’s neck.
– During the journey, do not allow the
child to stay in abnormal positions or release
the belts.
– Do not carry children in your arms, not
even small babies. No-one, however strong,
can keep hold od them in a crash.
– In the case of accidents, replace the
child’s seat with a new one.
PRESETTING FOR
MOUNTING
“ISOFIX TYPE” CHILD
RESTRAINT SYSTEM
The rear seat of your car is preset for
mounting the Isofix type child restraint sys-
tem, a new European standardised system
for carrying children safely. Isofix type child
restraint system is an additional option that
does not prevent from using traditional child
restraint systems. Isofix type child restraint
system covers three weight groups: 0, 0+
and 1.
Due to its different anchoring system, the
Isofix child’ seat shall be anchored just us-
ing the metal brackets (A-fig. 47) set be-
tween rear seat back and cushion.
fig. 47
A0A0671b

GETTING TO KNOW YOUR CAR
37
Mount the child restraint
system only with the car
stationary. The Isofix child
restraint system is properly an-
chored to the mounting brackets
when clicks are heard. In any case,
keep to the installation instructions
that must be provided by the child
restraint system Manufacturer.– push the child restraint system until hear-
ing the locking clicks;
– check proper locking by moving the
child’s seat with force: the built-in safety
mechanism actually inhibits proper coupling
with only one coupling locked.
It is actually possible to mount both the
traditional restraint system and the Isofix
one, e.g. the traditional one on the left and
the Isofix type seat on the right.
Since sizes are different, on the rear seats
it is possible to install just two traditional
child’s seats, or two Isofix type seats. On
the front passenger seat it is only possible
to mount traditional child’s seats.
Only Isofix type child restraint systems de-
signed and tested for this car must be used.
fig. 48
A0A0663b
MOUNTING THE ISOFIX TYPE
CHILD’S SEAT
Groups 0 and 0+
For children of the 0 and 0+ group (ba-
bies up to 13 Kg), the child’s seat is facing
backwards and the child is restrained by the
child’s seat belts(D-fig. 48).
As the child grows, passing to weight group
1, the child’s seat shall be fitted facing for-
wards.
For proper mounting proceed as follows:
– check whether the release lever (B) is
at rest position (inward);
– find the presetting brackets (A), then
position the child restraint system with the
fastening devices (C) aligned with the brack-
ets;

GETTING TO KNOW YOUR CAR
38
Group 1
For proper mounting proceed as follows:
– check whether the release lever (B-
fig. 49) is at rest position (inward);
– find the presetting brackets (A), then
position the child restraint system with fas-
tening devices (C) aligned with the brack-
ets;
– push the child restraint system until hear-
ing the locking clicks;
– check proper locking by moving the
child’s seat with force: the built-in safety
mechanism actually inhibits improper cou-
pling with only one coupling locked.AIR BAG
The car is fitted with front air bags for the
driver and for the passenger (side bags - win-
dow bags).
FRONT AIR BAGS
The front air bag (driver’s and passenger’s)
has been designed to protect the occupants
in the event of head-on crashes of medium-
high severity by placing the cushion between
the occupant and the steering wheel or dash-
board.
Front air bags are designed to protect the
car occupants in front crashes and therefore
non-activation in other types of collisions
(side collisions, rear-end shunts, roll-overs,
etc...) is not a system malfunction.
In the case of a crash, an electronic con-
trol unit, when necessary, triggers inflation
of the cushion.
The cushion inflates instantaneously, set-
ting itself between the body of the front oc-
cupants and the structures that could cause
injury. The cushion then deflates immedi-
ately afterwards. With this configuration, the child is secured
also by the car seat belts and by the upper
belts. To apply car seat belts to child’s seat
refer to the child’s seat handbook.
fig. 49
A0A0664b

GETTING TO KNOW YOUR CAR
50
TO MEMORISE
THE SPEED
Move the ring (A) to ONand take the car
to the required speed normally. Turn the ring
(B) to (+) for at least three seconds, then
release it. The car speed is memorised and
it is therefore possible to release the accel-
erator pedal.
The car will continue to travel at the mem-
orised constant speed until one of the fol-
lowing conditions takes place:
– pressing the brake pedal;
– pressing the clutch pedal;
– if the ASR, MSR or ESP system cuts in;
– with Selespeed transmission if a gear is
changed;
– inadvertent movement of the Selespeed
gear control lever to position N.
IMPORTANTIn the case of need (when
overtaking for instance) acceleration is pos-
sible simply pressing the accelerator pedal;
later, releasing the accelerator pedal, the car
will return to the speed memorised previ-
ously.
TO RESET THE
MEMORISED SPEED
If the device has been disengaged for ex-
ample pressing the brake or clutch pedal,
the memorised speed can be reset as fol-
lows:
– accelerate gradually until reaching a
speed approaching the one memorised;
– engage the gear selected at the time
of speed memorising (4th, 5th or 6th
speed);
– press the RESbutton (C).
TO INCREASE THE
MEMORISED SPEED
The speed memorised can be increased
in two ways:
1) pressing the accelerator and then mem-
orising the new speed reached (turning the
ring to (B) for more than three seconds);
or
2) momentaneously turning the ring (B)
to (+): each pulse of the ring will correspond
to a slight increase in speed (about 1.5
km/h) while pressing continuously will cor-
respond to a continuous speed increase. Re-
leasing the ring (B) the new speed will be
memorised automatically. –ONis the normal operating position of
the device. When the ring (A) is in this
position, the warning light
Üon the in-
strument cluster turns on.
Ring (B) serves for memorising and main-
taining the car sped or for increasing or low-
ering the speed memorised.
Turn the ring (B) to (+) to memorise the
speed reached or increase the speed mem-
orised.
Turn the ring (B) to (–) to lower the speed
memorised.
Each time the ring is actuated (B) the speed
increases or lowers by about 1.5 km/h.
Keeping the ring turned the speed changes
continuously. The new speed reached will
be maintained automatically.
TheRESbutton (C) resets the memorised
speed.
IMPORTANTTurning the ignition key to
STOPor the ring (A) to OFF, the speed
memorised is cleared and the system is
switched off.

GETTING TO KNOW YOUR CAR
51
TO REDUCE THE
MEMORISED SPEED
The speed memorised can be reduced in
two ways:
1) disengaging the device (for instance
pressing the brake pedal) and then memo-
rising the new speed (turning the ring (B)
to (+) for at least three seconds);
2) keeping the ring pressed (B) at (–)
until reaching the new speed which will be
memorised automatically.The device may only be engaged in in 4th,
5th or 6th gear, depending on the speed
of the car. Travelling downhill with the de-
vice engaged the car speed may increase
more than the memorised one, due to the
change in the engine load.
The ring (A) may be left constantly at ON
without damaging the device. You are, how-
ever, advised to switch the device off when
not in use, turning the ring to OFF, to avoid
memorising speeds by accident. It is advisable to engage the cruise control
only when the conditions of the traffic or
roads so permit under completely safe con-
ditions, i.e.: straight and dry roads, dual car-
riage ways or motorways, flowing traffic and
smooth road surface. Do not engage the de-
vice in town or in heavy traffic conditions.When travelling with the
cruise control on, do not
move the gearshift lever to
neutral and do not move the Sele-
speed selector to N.
Cruise control may only
be engaged at speeds be-
tween 30 and 190 km/h.
If the device is faulty or
not working, turn the ring
(A) to OFF and contact Al-
fa Romeo Authorised Services af-
ter checking that the protection
fuse is intact.
TO RESET THE MEMORISED
SPEED
The memorised speed is automatically re-
set turning off the engine or moving the ring
(A) to OFF.

GETTING TO KNOW YOUR CAR
56
SPEEDOMETER
(SPEED INDICATOR)
The gauge (A-fig. 72) indicates the car
speed.
ODOMETER
Odometer display (B-fig. 72) with dou-
ble meter (total and trip) and headlamp po-
sition display.
The display shows:
– the mileage on the first line (6 figures)
– the trip meter on the second line (4 fig-
ures)
– aside the position of the headlight aim-
ing device.To reset the trip meter, keep button (A-
fig. 73) on the plate at the side of the
steering column pressed for a few seconds.
IMPORTANTIf the battery is discon-
nected the trip meter reading is not stored.REV COUNTER (fig. 74)
The danger zone (red, or white on certain
versions) indicates excessive high engine
speed. Do not drive for long periods with the
pointer in this area.IMPORTANTThe electronic injection con-
trol system gradually shuts off the flow of fu-
el when the engine is “over-revving” resulting
in a gradual loss of engine power.
When the engine is idling, the rev counter
may indicate a gradual or sudden highering of
the speed, this is normal as it takes place dur-
ing normal operation, for example when en-
gaging the climate control system or the fan.
In particular a slow change in the speed pre-
serves the battery charge.
fig. 73
A0A1104b
fig. 74
A0A0757b
fig. 72
A0A0756b

GETTING TO KNOW YOUR CAR
63
Engine oil level check
(JTD versions)
Turning the ignition key to MARthe dis-
play shows the engine oil level for a few sec-
onds. During this phase, to clear the display
and move to next screen, press briefly but-
tonMODE.
IMPORTANTTo make sure that the en-
gine oil level displayed is correct, carry out
the check with the car on level ground.
Fig. 85refers to the correct engine oil
level display. As the oil level gradually falls,
the full bars go off leaving room for the emp-
ty ones.
fig. 85
A0A9101g
fig. 86
A0A9102g
fig. 87
A0A9103g
Fig. 86refers to the display with an oil
level below the preset minimum. In this con-
dition the bars are all empty.
IMPORTANTIn this case the correct en-
gine oil level should be restored as soon as
possible, see “Checking levels” in section
“Car maintenance”. Fig. 87refers to the display with an oil
level above the preset maximum. In this con-
dition the bars are all full.
IMPORTANTIn this case, contact Alfa
Romeo Authorised Services who will restore
the correct engine oil level.