2009 Alfa Romeo GT buttons

GETTING TO KNOW YOUR CAR
150
Selecting CD/CD Changer
functions
Pressing briefly and repeatedly button CD
it is possible to select the following audio
sources in sequence:
– CD (only if the Compact Disc is insert-
ed);
– CHANGER (only if the CD Changer is con-
nected).
Audio source memory function
If while listening to a CD another function
is selected (e.g.: the radio), playing is
stopped and when the CD mode is resumed,
it starts again from the point in which it was
stopped.
If while listening to the radio another func-
tion is selected, when the Radio mode is
resumed, it is tuned to the last station se-
lected.Volume adjustment
Adjust volume through VOL + and VOL -
buttons.
If the volume level is changed during the
broadcast of a traffic bulletin, the new set-
ting is maintained only until the end of the
bulletin.
SVC function
(excluding versions with
Bose HI-FI system)
The SVC function makes it possible to au-
tomatically adapt the volume level to the
speed of the car, increasing it as the speed
increases to maintain the ratio with the noise
level inside the passenger compartment.
See section MENU for activating/deacti-
vating this function. FUNCTIONS AND
ADJUSTMENTS
Turning the sound system on The set is
switched on pressing button ON.
When turning the sound system on, the
volume level will be brought to 20 if it was
set to over.
If the radio is turned on when the key is
not fitted into the ignition device, it will turn
off automatically after about 20 minutes.
After automatic switching off, it is however
possible to turn the radio on again for oth-
er 20 minutes by pressing button ON (see
paragraph “IGN TIME function”).
Turning the sound system off
Keep button ON pressed.
Selecting radio functions
Pressing briefly and repeatedly button
FM
ASit is possible to select the following
functions in sequence:
– TUNER (“FM1”, “FM2”, “FMT”);
Pressing briefly and repeatedly button AM
it is possible to select the following functions
in sequence:
– TUNER (“MW”, “LW”).

GETTING TO KNOW YOUR CAR
151
Audio adjustments
The options proposed by the audio menu
differ according to the audio source select-
ed: AM/FM/CD/CDC.
To change Audio functions, press briefly
button AUD. The display will show “BASS”.
To scroll the Menu options, use buttons
▲
or▼. To change the setting of the option
selected, press buttons
÷or˜.
The display will show the current status
of the function selected.
The functions controlled by the menu are
the following:
– BASS (bass adjustment);
– TREBLE (treble adjustment);
– BALANCE (right/left balance);
– FADER (excluding versions with Bose HI-
FI system) (front/rear balance);
– LD (excluding versions with Bose HI-FI
system) (Loudness on/off);
– PRESET (excluding versions with Bose
HI-FI system) (standard equalization acti-
vation and selection);
– XX USER (personal equalization set-
ting).Tone adjustment
(bass/treble)
Proceed as follows:
– Use button
▲or▼to select “BASS” or
“TREBLE” in the AUDIO menu;
– press button
÷or˜to in-
crease/decrease the basses or trebles.
Pressing the buttons briefly the change is
gradual by steps. Pressing longer, chang-
ing is faster.
Balance adjustment
Proceed as follows:
– Use button
▲or▼to select “BAL-
ANCE” in the AUDIO menu;
– press button
÷to increase the sound
from the right speakers or button
˜to
increase the sound from the left speakers.
Pressing the buttons briefly the change is
gradual by steps. Pressing longer, chang-
ing is faster.
Select “
÷0˜” to set the same val-
ue for both right and left speakers. Mute /pause function
(turning off the volume
completely)
To switch on the Mute function, briefly
press the button MUTE. Volume will gradu-
ally lower and the display will show the word
“MUTE” (when in radio mode) or “PAUSE”
(when in CD or CD-Changer mode).
To switch off the Mute function, press the
button MUTE again. Volume will gradually
become louder returning to the value set be-
fore switching on the Mute function.
Changing volume will deactivate the Mute
function and the volume will be set to the
new level selected.
With the Mute function on:
– if an emergency alarm or a traffic bul-
letin arrives with the TA function on, the mes-
sage ignores the Mute function. The Mute
function will be resumed at the end of the
traffic announcement.

GETTING TO KNOW YOUR CAR
152
PRESET/XX EQ SET*/CLASSIC/
ROCK/JAZZ functions
(equalizer on/off)
The integrated equalizer can be turned on
or off. With the equalizer off, it is possible
to change the sound settings only adjust-
ing the bass (“BASS”) and treble tones
(“TREBLE”), while activating the function
makes it possible to adjust the sound curves.
To turn the equalizer off, select “PRESET”
by means of button
÷or˜.
To turn the equalizer on, use button
÷
or˜to select one of the following op-
tions:
– “USER” (adjustment of the 7 equaliz-
er bands that can be changed by the user);
– “CLASSIC” (predefined equalizer ad-
justment for best playing of classic music);
– “ROCK” (predefined equalizer adjust-
ment for best playing of rock and pop mu-
sic);
– “JAZZ” (predefined equalizer adjust-
ment for best playing of jazz music).
When one of the equalizer settings is on,
the display shows “EQ”. *XX EQ SET function (only if the
USER equalizer setting has been
selected) (excluding versions
with Bose HI-FI system)
To set a personal equalizer adjustment, use
button
▲or▼to select USER and then
press button
▼for long.
The display will show for about 2 seconds
“XX EQ SET” and then a graph with 7 bars,
where each bar represents a frequency.
Choose the bar to be adjusted using button
÷or˜; the bar chosen starts to flash
and it is possible to adjust it using button
▲
or▼.
To store the new settings, press button
AUD again or wait for about 10 seconds.
The display will show the word “MEN” to-
gether with the graph with 7 bars.
Antitheft protection
Refer to “CD Player” paragraph. Fader adjustment
Proceed as follows:
– Use button
▲or▼to select “FADER”
in the AUDIO menu;
– press button
÷to increase the sound
from the rear speakers or button
˜to in-
crease the sound from the front speakers.
Pressing the buttons briefly the change is
gradual by steps. Pressing longer, chang-
ing is faster.
Select “
÷0˜” to set the same val-
ue for both front and rear speakers.
LD function
The Loudness function improves the sound
volume when listening at low level, in-
creasing the basses and trebles.
To switch the function on/off, use button
▲or▼to select “LD” in the AUDIO menu.
The function condition (on or off) is shown
on the display for few seconds by “LD ON”
or “LD OFF”.

GETTING TO KNOW YOUR CAR
153
Each band is shown by the respective
wording on the display.
The last station selected in the respective
frequency band will be tuned.
The FM band is divided into sections: FM1,
FM2 and FMT. The FMT reception band is
reserved to the stations stored automatically
with the Autostore function.
Presetting buttons
The buttons with symbols from 1 to 6
make it possible to set the following pre-
settings:
– 18 in the FM band (6 in FM1, 6 in
FM2, 6 in FMT);
– 6 in the MW band;
– 6 in the LW band;
To call a preset station, choose the required
frequency band and then press briefly the
corresponding preset button (from 1 to 6).
Pressing the respective preset button for
longer than 2 seconds will store the tuned
station. Storing is confirmed by a beep. Storing the last station heard
The radio automatically keeps in storage
the last station heard for each reception
band, which is then tuned when the radio is
turned on or the reception band is changed.
Automatic tuning
Briefly press button
÷or˜to start
automatically searching the tuning for the
next station that it is possible to receive in
the direction chosen.
If button
÷or˜is pressed for
longer, quick searching takes place. When
the button is released, the tuner stops on
the next receivable station.
If the TA function is on (traffic information),
the tuner only searches stations which broad-
cast traffic bulletins.
RADIO (TUNER)
Introduction
When the set is turned on the last function
selected before turning off is played (Radio,
CD or CD Changer).
To select the Tuner source while listening
to another audio source, press briefly but-
tons FM
ASor AM, according to the required
frequency band.
When Tuner is on, the display will show
the selected station name (RDS stations on-
ly) (or frequency), the frequency band (e.g.:
FM1) and the preselection button number
(e.g.: P1).
Selecting the frequency band
If in the Tuner mode, briefly and repeat-
edly press button FM
ASor AM to select the
required frequency band.
Every time the button is pressed the fol-
lowing bands are selected in sequence:
– Pressing button FM
AS: “FM1”, “FM2”,
“FMT”;
– Pressing button AM: “MW” and “LW”.

GETTING TO KNOW YOUR CAR
154
A-STORE function
(automatic station storage)
To switch on the A-STORE function, keep
button FM
ASpressed until receiving the con-
firmation beep. With this function the ra-
dio automatically stores the six stations with
the strongest signal in decreasing order of
intensity of the FMT frequency band.
IMPORTANTActivating the A-STORE
function cancels the stations stored previ-
ously in the FMT band.
If the TA function is on (traffic information),
only the stations that send traffic informa-
tion will be stored.
During automatic storage the display
shows “A-STORE”.
To interrupt A-STORE press button FM
AS
again: the radio will automatically tune to
the station heard before activation of the Au-
toSTore function. At the end of the A-STORE function the ra-
dio automatically tunes on the first preset
station in the FMT band stored on preset but-
ton 1.
On buttons numbered from 1 to 6, the sta-
tions are automatically stored that give a
strong signal in that moment in the present
band.
Activating the A-STORE function in MW or
LW bands will automatically select the FMT
band where the function is then run.
IMPORTANTSometimes the A-STORE
function is unable to find 6 stations with a
strong signal. In this case the previous sta-
tions will be stored on the free preset but-
tons. Manual tuning
This allows manual station searching in the
chosen band.
Select the required frequency band and
then press briefly and repeatedly button
▲
or▼to start searching in the chosen band.
Pressing one of the buttons
▲or▼longer
obtains fast forward searching, which is
stopped when the button is released.

GETTING TO KNOW YOUR CAR
157
The display will show the current status
of the function:
– “REG ON”: function on.
– “REG OFF”: function off.
If the function is off and a regional pro-
gramme is tuned that works in a determi-
nate area and the car enters a different area,
the regional station of the new area is re-
ceived.
IMPORTANTIf AF and REG are both ac-
tive, when passing from one region to an-
other the radio could not tune properly to
a valid alternative frequency. MP3 DISP function
(MP3 CD data display)
With this function it is possible to choose
the information shown on the display, when
listening to a MP3 CD.
This function can be selected only if a MP3
CD is loaded: in this event the display shows
“MP3 DISP”.
To change the function use buttons
÷
or˜.
The display shows the setting among the
six possible:
– TITLE (track title, if ID3-tag available)
– AUTHOR (track author, if ID3-tag avail-
able)
– ALBUM (album title, if ID3-tag available)
– DIR (directory name);
– FILENAME (MP3 file name);
– TIME (time elapsed from start of track). REG function
(regional broadcast reception)
Certain national broadcasters, at determi-
nate times of the day, transmit regional pro-
grammes which differ from region to region.
This function makes it possible to tune in on-
ly on local stations (regional) (see para-
graph “EON function”).
Activate this function if you want to tune
automatically to regional stations broad-
casting in the selected band.
To turn the function on/off use button
÷or˜.