Page 108 of 313
FITTINGS
BOOT FITTINGS
1. Load space screen
(see details on following page)
2. Storage box
3. 12 V
accessories socket
(see details on following page)
4. Hooks
(see details on following page)
5. Stowing rings
6. High load retaining net
(see details on following page)
7. Rear armrests with can holder
8. Luggage retaining strap
9. Location for torch or for Hi-Fi
a m p l i fi e r
(see details on following page)
Page 109 of 313
i
115
FITTINGS
Load space screen
To install the load space screen:
position one of the ends of the roller
in its support,
i n s e r t t h e s e c o n d e n d i n i t s s u p p o r t ;
the catch locks automatically,
unroll the load space screen to the
boot pillars,
insert the load space screen guides
in the rails on the boot pillars.
To store the load space screen, place it
a t t h e b o o t s i l l , r o l l e r u p p e r m o s t a n d fl a p
facing inwards.
To remove the load space screen:
remove the load space screen
guides from the rails on the boot
pillars,
roll up the load space screen in its
roller,
pull and support the catch at one of
the ends of the roller to release it,
remove the roller from its support
from the released end, then from the
second.
You can access the boot by open-
ing the rear screen and raising the
l o a d s p a c e s c r e e n fl a p .
Page 111 of 313
!i
117
FITTINGS
Torch
This is a removable light, incorporated
in the boot wall, which can be used to
light the boot or as a torch.
For the boot lighting function, refer to
t h e " V i s i b i l i t y - § B o o t l i g h t i n g " s e c t i o n .
Operation
This torch operates with NiMH type ac-
cumulators.
I t h a s a n o p e r a t i n g a u t o n o m y o f a p p r o x i -
mately 45 minutes and charges while
you are driving. Use
E x t r a c t t h e t o r c h f r o m i t s l o c a t i o n
pulling it upwards.
Press the switch, located on the
back, to switch the torch on or off.
U n f o l d t h e s u p p o r t , l o c a t e d o n t h e
back, to set down and raise the
t o r c h ; f o r e x a m p l e , w h e n c h a n g i n g
a wheel.
Storing
Put the torch back in place in its
location starting with the lower part.
If you have forgotten to switch off the torch, this switches it off
automatically. Side blinds
Fitted on the rear windows of the 2nd
row, these protect your young children
from the sun.
Pull the blind by the central tab.
Position the blind attachments on
the corresponding hooks.
O b s e r v e t h e p o l a r i t i e s w h e n fi t t i n g
the accumulators.
Never replace the accumulators
with batteries. It the torch is not engaged correctly,
it may not charge and may not come
on when the boot is opened.
Page 131 of 313
i
i
135
SAFETY
2nd row rear centre
seat belt
Installation Removal and storing
Press the red button on the buckle B ,
then on the buckle A .
Guide the strap as it reels in and
bring the tongue B , then A onto the
magnet of the attachment point on
the roof.
3rd row rear seat belts
Installation
Pull the strap and insert the tongue C in the buckle, on the boot side trim
side.
Insert the tongue D in the opposite
buckle.
Check the fastening of each buckle
by pulling the strap.
Pull the strap and insert the tongue A
in the left-hand buckle.
Insert the tongue B in the right-hand
buckle.
Check the fastening of each buckle
by pulling the strap.
The seat belts for the rear seats of the
3rd row are located at the corner of the
corresponding boot pillar and roof. If the two outer seats of the 2nd row
are moved inwards, always use the
outer rear seat belts.
Removal and storing
Press the red button on the buckle D ,
then on the buckle C .
Guide the strap as it reels in and
bring the tongue D , then C onto the
magnet of the attachment point on
the corresponding boot pillar.
The seat belt for the rear centre seat of
the 2nd row is located at the rear left of
the roof.
The 3rd row of seats (SW with
p a n o r a m i c s u n r o o f ) i s n o t fi t t e d
with seat belt unfastened warning
lamps.
Page 161 of 313
11
i
165
PRACTICAL INFORMATION
This repair kit is available from
PEUGEOT dealers.
It is designed to repair most punc-
tures which could affect the tyre, lo-
cated on the tyre tread or shoulder.
Avoid removing any foreign bodies
which have penetrated the tyre.
TEMPORARY PUNCTURE REPAIR KIT
The kit is stowed in the boot below the
fl o o r . I t i s fi t t e d i n t h e t o o l b o x , l o c a t e d
below the storage compartment. Using the kit
This procedure, comprising several
steps, must be carried out in full.
Switch off the ignition.
Turn the selector A to the "SEALANT"
position.
Check that the switch B is in
position "0" .
Connect the white pipe C to the
valve of the tyre to be repaired.
Connect the compressor's electric
plug to the vehicle's 12 V socket.
A f fi x t h e s p e e d l i m i t a t i o n s t i c k e r
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.
Start the vehicle and leave the
engine running.
Access to the kit
Complete system consisting of a com-
pressor and an incorporated sealant
cartridge which permits
temporary re-
pair of the tyre so that you can drive to
the nearest garage.
Page 164 of 313
11
i
168
PRACTICAL INFORMATION
This repair kit is available from
PEUGEOT dealers.
It is designed to repair holes of a
m a x i m u m d i a m e t e r o f 6 m m , l o c a t -
e d e x c l u s i v e l y o n t h e t y r e t r e a d o r
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
TEMPORARY TYRE REPAIR KIT
Complete system consisting of a compres-
sor and a bottle of sealant which permits
temporary repair of the tyre so that you
can drive to the nearest garage.
The kit is installed in the boot storage
tray. Using the kit
Switch off the ignition.
Tick the wheel to be repaired on the
speed limitation sticker enclosed
t h e n a f fi x t h e s t i c k e r t o t h e v e h i c l e ' s
steering wheel to remind you that a
wheel is in temporary use.
Clip the bottle 1 on the compressor 2 .
Check that the switch A is tilted to
position "0" .
Connect the pipe of the bottle 1 to
the valve of the tyre to be repaired.
Unwind the pipe of the compressor
2
fully, then connect it to the bottle.
Connect the compressor's electric
plug to the vehicle's 12 V socket.
Start the vehicle and leave the
engine running.
Page 167 of 313
11
i
171
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed in the boot under
t h e fl o o r .
T o g a i n a c c e s s t o t h e m :
open the boot,
r a i s e t h e fl o o r ,
secure it by hooking its cord on the
hook on the rear shelf support,
u n c l i p a n d r e m o v e t h e b o x c o n t a i n i n g
the tools. A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
vehicle. Do not use them for other
purposes.
1. Wheelbrace.
For removal of the wheel trim and r e m o v a l o f t h e w h e e l fi x i n g b o l t s .
2. Jack with integral handle.
For raising the vehicle.
3. Socket for the security bolts
( l o c a t e d i n t h e g l o v e b o x ) .
For adaptation of the wheelbrace to the special security bolts.
List of tools
Access to the tools
Wheel with trim
When removing the wheel , d e t a c h t h e t r i m fi r s t u s i n g t h e w h e e l b r a c e 1 pulling
at the valve passage hole.
W h e n r e fi t t i n g t h e w h e e l , r e fi t t h e t r i m s t a r t i n g b y p l a c i n g i t s n o t c h f a c i n g t h e
valve and press around its edge with the palm of your hand.
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
Page 168 of 313
11
i
i
172
PRACTICAL INFORMATION
Fixing the steel spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y
wheels, it is normal to notice, when
t i g h t e n i n g t h e b o l t s o n fi t t i n g , t h a t
the washers do not come into con-
tact with the steel spare wheel. The
wheel is secured by the conical
contact of each bolt.
Access to the spare wheel
The spare wheel is installed in the boot
u n d e r t h e fl o o r .
According to country, the spare wheel
may be steel or alloy.
To gain access to it, refer to the paragraph
"Access to the tools" on the previous
page.
Taking out the wheel
Unscrew the yellow central bolt.
Raise the spare wheel towards you
from the rear.
Take the wheel out of the boot.
Putting the wheel back in place
Put the wheel back in its housing.
Unscrew the yellow central bolt by a
few turns then put it in place in the
centre of the wheel.
Tighten fully until the central bolt
clicks to retain the wheel correctly.
P u t t h e b o x b a c k i n p l a c e i n t h e
centre of the wheel and clip it.
T y r e u n d e r - i n fl a t i o n d e t e c t i o n
T h e s p a r e w h e e l i s n o t fi t t e d w i t h
a sensor. The punctured wheel
must be repaired by a PEUGEOT
dealer.
