2009.5. PEUGEOT 3008 lights
[x] Cancel search: lightsPage 10 of 290
32
Warning lightsis onCauseActions, observations
Engine autodiagnostics system
fi x e d . The emission control system is faulty.
This light should switch off when the engine is started.
If it does not switch off, contact a P E U G E O T d e a l e r .
fl a s h i n g .
The engine management system is faulty, there is a risk of destruction of the catalytic converter.
You must stop immediately where it is safe to do so.
Park, switch off the ignition and contact a P E U G E O T d e a l e r .
Low fuel level fi x e d w i t h t h e n e e d l e in the red zone. The fuel tank contains approximately 5 litres.
Depending on your style of driving and your engine, you have enough fuel left to drive approximately 30 miles (50 km).
Fill your fuel tank as soon as possible. Capacity approximately 60 litres.
Never continue to drive until you run out of fuel, this could damage the emission control and injection systems.
Coolant temperature fi x e d w i t h t h e n e e d l e in the red zone. The temperature of the cooling system is too high.
You must stop immediately where it is safe to do so.
Wait until the engine has cooled down before topping up the level, if necessary.
If the problem persists, park, switch off t h e i g n i t i o n a n d c a l l a P E U G E O T d e a l e r .
Engine oil pressure fi x e d . The engine lubrication circuit is faulty.
You must stop immediately where it is safe to do so.
Park, switch off the ignition and contact a P E U G E O T d e a l e r .
Battery charge fi x e d .
The battery charging circuit is faulty (dirty or loose terminals, slack or cut alternator belt, ...).
This light should switch off when the engine is started.
If it does not switch off, contact a P E U G E O T d e a l e r .
Page 11 of 290
33
Warning lightsis onCauseActions, observations
Door(s) open
fi x e d i f t h e s p e e d i s below 6 mph (10 km/h). A door, the boot, the lower tailgate or the bonnet (only with alarm) is still open. Close the access concerned. fi x e d i f t h e s p e e d i s above 6 mph (10 km/h), accompanied by an audible signal.
Seat belt not fastened/unfastened
fi x e d t h e n fl a s h i n g accompanied by an audible signal.
The driver and/or the front passenger has not fastened or has unfastened his seat belt.
One or more rear passengers have also unfastened their seat belt.
Pull the strap then insert the tongue in the buckle.
Air bags
temporarily.
This light comes on for a few seconds then switches off when you turn the ignition to "ON".
This light should switch off when the engine is started.
If it does not switch off, contact a P E U G E O T d e a l e r .
fi x e d . One of the air bag or seat belt pretensioner systems is faulty. C o n t a c t a P E U G E O T d e a l e r .
Water in diesel fi x e d .
T h e d i e s e l fi l t e r c o n t a i n s water.
There is a risk of damage to the injection system on Diesel engines.
C o n t a c t a P E U G E O T d e a l e r w i t h o u t delay.
Directional headlamps fl a s h i n g . The directional headlamps system is faulty. C o n t a c t a P E U G E O T d e a l e r .
D e fl a t e d wheel fi x e d . The pressure in one or more wheels is too low. Check the pressure of the tyres as soon as possible.
Page 16 of 290
38
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life.
Lighting rheostat
System for manual adjustment of the
brightness of the instrument panel in rela-
tion to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the igni-
tion is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.
With the ignition on, press the but-
ton until zeros appear. Activation
When the lights are on:
press the button to change the
brightness of the instrument panel,
when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or
when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,
when the lighting reaches the level
of brightness required, release the
button. When the lights are on, you
cannot switch the lighting off
but you can adjust it to mini-
mum.
Deactivation
When the lights are off, or in day mode
o n v e h i c l e s fi t t e d w i t h d a y t i m e l i g h t s ,
pressing the button does not have any
effect.
Page 18 of 290
40
V e h i c l e c o n fi g u r a t i o n Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active, not
active, faulty).
Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-Brasil,
Türkçe, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode. Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).
Once you have selected a setting,
press the "OK" button to change its
value.
Wait for approximately ten seconds
without any action to allow the changed
data to be recorded or press the "ESC" button to cancel.
The display then returns to the normal
display.
O n c e t h e " V e h i c l e c o n fi g u r a t i o n " m e n u
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- selective unlocking (refer to the "Accesses" section),
-
"follow-me-home" and welcome light-
ing (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- automatic or manual parking brake (refer to the "Driving" section),
- ... For safety reasons, it is impera-
t i v e t h a t c o n fi g u r a t i o n o f t h e
multifunction displays by the
driver takes place when sta-
tionary.
Page 20 of 290
42
For safety reasons, it is impera-
t i v e t h a t c o n fi g u r a t i o n o f t h e m u l -
tifunction displays by the driver
takes place when stationary.
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-Brasil,
Türkçe, Deutsch, English, Espanol).
Units
Once the "Units" menu has been selected,
you can change the units of the following
parameters:
- temperature (°C or °F),
- fuel consumption (l/100 km, mpg or
km/l).
Once you have selected a setting,
press the " " or " " buttons to
change its value.
Press the " " or " " buttons to
switch respectively to the previous
or next setting.
Press the "OK" button to record
the change and return to the normal
display or press the "ESC" button to
cancel.
V e h i c l e c o n fi g u r a t i o n
O n c e t h e " V e h i c l e C o n fi g u r a t i o n " m e n u
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- selective unlocking (refer to the "Accesses" section),
-
"follow-me-home" and welcome light-
ing (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- automatic or manual parking brake (refer to the "Driving" section),
- ...
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active, not
active, faulty).
Page 22 of 290
44
"Vehicle diagnostics" menu
Press the "MENU" button to gain
access to the general menu.
Press the arrows, then the "OK"
button to select the " Vehicle diag-
nostics
" menu.
On the " Vehicle diagnostics
" menu, select the following application:
Warnings log
This summarises the active warning
messages, displaying them in succes-
sion on the multifunction display.
Once this menu has been selected, you
can consult information concerning the
status of the vehicle, such as the warnings
log.
D e fi n e t h e v e h i c l e p a r a m e t e r s
Once this menu has been selected, you
can activate or deactivate the following
equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- selective unlocking (refer to the "Accesses" section),
- "follow-me-home" and welcome light- ing (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- automatic or manual parking brake (refer to the "Driving" section),
- ...
"Personalisation-Configuration" menu
Once this menu has been selected, you
can gain access to the following func-
tions:
- d e fi n e t h e v e h i c l e p a r a m e t e r s ,
- d i s p l a y c o n fi g u r a t i o n ,
- selection of the language.
Page 25 of 290
47
"SETUP" menu
Press the "SETUP" button to gain
access to the "SETUP" menu. This
allows you to select from the follow-
ing functions:
- "Languages",
- "Date and time",
- "Display",
- "Vehicle parameters",
- "Units",
- "System parameters".
Languages
This menu allows you to select the lan-
guage used by the display: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Polski, Portugues, Türkçe * .
Date and time
This menu allows you to set the date
and time, the format of the date and the
format of the time (refer to the "Audio
a n d T e l e m a t i c s " s e c t i o n o r t o t h e s p e c i fi c
user guide given to you with the other
owner's documents). * According to country.
Display
This menu allows you to set the bright-
ness of the screen, the screen colour
scheme and the colour of the map (day/
night or auto mode).
Vehicle parameters
This menu allows you to activate or
deactivate certain driving and comfort
equipment:
- wiper linked with reverse gear (refer
to the "Visibility" section),
- selective unlocking (refer to the "Accesses" section),
- follow-me-home and welcome light- ing (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section),
- automatic or manual parking brake (refer to the "Driving" section),
- ...
Units
This menu allows you to select the
units: temperature (°C or °F) and con-
sumption (km/l, l/100 or mpg). For safety reasons, it is im-
p e r a t i v e t h a t c o n fi g u r a t i o n o f
the multifunction displays by
the driver is carried out when
stationary.
System parameters
This menu allows you to restore the fac-
t o r y c o n fi g u r a t i o n , d i s p l a y t h e s o f t w a r e
version and activate the scrolling text.
Page 41 of 290
61
S w i t c h i n g t h e s y s t e m o f f
T u r n t h e a i r fl o w c o n t r o l t o t h e l e f t
until all of the indicator lights switch
off.
This action switches off all of the func-
tions of the system.
Temperature related comfort is no long-
e r g u a r a n t e e d b u t a s l i g h t fl o w o f a i r ,
due to the movement of the vehicle, can
still be felt.
T u r n t h e a i r fl o w d i a l t o t h e r i g h t o r
press the "AUTO" button to reacti-
vate the system with the values set
before it was switched off.
Avoid driving for prolonged
periods with the system off.
9. Mono zone/Dual zone
Press this button to equa-
lise the comfort value on
the passenger side with that
o n t h e d r i v e r ' s s i d e ( m o n o
z o n e ) . T h e i n d i c a t o r l i g h t o n
the button comes on.
8. Air recirculation
This button activates the recir-
culation of air in the passenger
compartment and can permit
automatic operation.
Avoid prolonged recirculation
o f i n t e r i o r a i r ( r i s k o f c o n d e n -
sation and deterioration of the
a i r q u a l i t y ) .
S h u t t i n g o f f / I n t a k e o f a i r ( a u t o m a t i c
m o d e )
S h u t t i n g o f f t h e i n t a k e o f a i r ( m a n u a l
m o d e )
I n t a k e o f a i r ( m a n u a l m o d e )
Press this button to recir-
culate the interior air, the
indicator light comes on.
Air recirculation enables the passenger
compartment to be isolated from exte-
rior odours and smoke.
Press this button, the indi-
cator light comes on.
The automatic mode has an
exterior air quality sensor. It
analyses the air and isolates
the passenger compartment from the
outside when it detects the presence
o f p o l l u t a n t s ( e . g . i n a t u n n e l ) . I n t h i s
case, it activates the air recirculation
automatically.
Press this button to permit
the intake of outside air and
prevent condensation, the
indicator light switches off.
The air quality sensor is not active.