2009.5 Citroen C5 light
[x] Cancel search: lightPage 160 of 314
IX
142
D R I V I N G
CRUISE CONTROL
S y s t e m w h i c h a u t o m a t i c a l l y m a i n -
tains the vehicle speed programmed
by the driver, without any action on
the accelerator pedal.
The cruise control is switched on
manually: the vehicle speed must be
at least 25 mph (40 km/h) and you
must be in at least:
- 4th gear for manual gearboxes,
- 2nd gear for automatic gearboxes. Displays on the instrument
panel
The programmed information is
grouped together in zone
A of the
instrument panel.
Programming
Press button 4 to select cruise
control mode "
CRUISE
" .
Steering mounted controls
The cruise control switches are lo-
cated on the left-hand side of the
steering wheel. T h e s e l e c t i o n i s c o n fi r m e d b y t h e
display of the function in zone
A of
the instrument panel.
When the function is selected, no
cruising speed has yet been
memorised. Once the desired speed has been
reached using the accelerator, press
button
1 or button 2 . The cruising
speed is then memorised and cruise
control is activated. The cruising
speed is displayed in zone A of the
instrument panel, and "ON" is dis-
played.
Adjustment of the memorised
speed while cruise control is
in operation
You can adjust the memorised
speed, displayed in zone A , by
pressing:
- Button 1 to increase the speed.
- Button 2 to reduce the speed.
S u c c e s s i v e p r e s s e s w i l l m o d i f y t h e
cruise speed in steps of 1 mph and a
continuous press in steps of 5 mph.
You can then release the accelera-
tor pedal. The vehicle will automati-
cally keep to the speed chosen.
The vehicle speed may vary slightly
from that memorised.
If during cruise control the system
cannot keep to the cruise speed
(e.g. on a steep descent), then the
s p e e d fl a s h e s . I f n e c e s s a r y , b r a k e t o
curb your speed.
Page 161 of 314
IX
!
143
D R I V I N G
Cruise control must only be
u s e d w h e r e t h e t r a f fi c c o n d i -
tions permit driving at a con-
stant speed.
Do not use it on congested roads
or when the weather or the road
conditions are poor.
The driver must remain attentive
and in complete control of the ve-
hicle.
You are recommended to keep your feet within range of the pedals.
Overriding the programmed
speed
While cruise control is in operation,
it is always possible to go above the
programmed speed simply by pres-
sing the accelerator pedal (for ex-
ample to overtake another vehicle).
The speed displayed in zone A
fl a s h e s .
You only have to release the ac-
celerator pedal to return to the pro-
grammed speed.
Suspension/Resumption
Either by pressing the brake
pedal or the clutch pedal.
Or by pressing button 3 .
O r b y t h e E S P o r A S R s y s t e m s
being active.
For vehicles with a manual gearbox,
cruise control is deactivated if the
gear lever is in neutral. Reactivation
-
By recalling the memorised
speed
After deactivation, press button 3 .
Your vehicle automatically returns
to the memorised cruising speed.
The memorised speed and "ON"
are displayed in zone A .
If the memorised cruising speed is higher than the current speed,
the vehicle will accelerate strong-ly to reach the current speed.
- By selecting the current speed
Press button 1 or 2 once the de-
sired speed has been reached.
The new speed and "ON" will
appear in zone A .
Return to normal driving
Either press on button 5 .
Or select the cruise control func-
tion.
Or stop the engine.
The speed that was chosen is no
longer memorised.
"PAUSE" will be displayed in zone A
of the instrument panel.
These actions do not cancel the
cruising speed which remains dis-
played on the instrument panel. Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 172 of 314
X
!
154
C H E C K S
RUNNING OUT OF FUEL (DIESEL)
HDi 110 engine
Unclip the protective cover to gain
access to the priming pump. HDi 140 and HDi 163 engines
Unclip the protective cover to gain
access to the priming pump.
Priming the fuel system
In the event of running out of fuel:
a f t e r fi l l i n g ( m i n i m u m 5 l i t r e s )
and removing the protective cov-
er, operate the manual priming
pump, until some resistance is
felt,
operate the starter motor while
depressing the accelerator pedal
slightly until the engine starts. HDi engines make use of ad-
vanced technology.
All maintenance and repairs require
s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a
CITROËN dealer can guarantee.
V6 HDi 240 engine with electric
pump
In the event of running out of fuel:
after adding fuel, turn the ignition
key to position M , wait for a few
seconds,
operate the starter motor until
the engine starts.
If the engine fails to start after several
attempts, contact a CITROËN dealer.
I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t
a t t e m p t , w a i t fi f t e e n s e c o n d s b e f o r e
trying again.
If the engine fails to start after a few
attempts, operate the priming pump
again and then try to start the engine.
When the engine is idling, accelerate
slightly to complete the bleeding of
the circuit.
Page 178 of 314
X
!
160
C H E C K S
Screenwash and headlamp
wash fluid
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e
topped up or replaced with water.
Reservoir capacities:
-
screenwash: approximately 3.5 litres,
- screenwash and headlamp wash: approximately 6.15 litres. Diesel additive level
(Diesel engine with particle
emission filter)
A low additive level is indicated by
lighting of the service warning lamp,
accompanied by an audible warning
and a message on the multifunction
screen.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
u s e d o i l o r fl u i d s w i t h t h e s k i n .
M o s t o f t h e s e fl u i d s a r e h a r m f u l t o
health or indeed very corrosive.
Do not discard used oil or
fl u i d s i n t o s e w e r s o r o n t o t h e
ground.
Take used oil to a CITROËN dealer
(France) or an authorised waste
disposal site.
I n t h e c a s e o f v e h i c l e s fi t t e d
with headlamp washers, the
m i n i m u m l e v e l o f t h i s fl u i d i s
indicated by an audible sig-
nal and a message on the multifunc-
tion screen.
Top up the level when you stop the
vehicle.
Coolant level
Coolant change
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the
manufacturer's recommendations. The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
a p a r t i c l e e m i s s i o n fi l t e r , t h e f a n
may operate after the vehicle has
been switched off, even if the en-
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.
Page 179 of 314
X
161
C H E C K S
CHECKS
Unless otherwise indicated, check
these components in accordance
with the Maintenance and Warranty
Guide and according to your engine.
Otherwise, have them checked by a
CITROËN dealer.
Battery The battery does not re-
quire any maintenance.
However, check that the
terminals are clean and
correctly tightened, particu-
larly in summer and winter.
When carrying out work on the bat-
tery, refer to the "Practical infor-
mation" section for details of the
precautions to be taken before dis-
connecting the battery and following
its reconnection.
Air filter and passenger compartment filter
Refer to the Maintenance
and Warranty Guide for
details of the replacement
intervals for these compo-
nents.
Depending on the environment (e.g.
dusty atmosphere) and the use of
the vehicle (e.g. city driving), replace
them twice as often if necessary
(refer to the “Engines” section).
A clogged passenger compartment
fi l t e r m a y h a v e a n a d v e r s e e f f e c t o n
the performance of the air condition-
ing system and generate undesirable
odours.
Oil filter
R e p l a c e t h e o i l fi l t e r e a c h
time the engine oil is
changed. Particle filter system (Diesel)
Complementary to the catalytic
c o n v e r t e r , t h i s fi l t e r m a k e s a n a c -
tive contribution to the preservation
of air quality by the retaining of the
unburnt pollutant particles. Black
exhaust fumes are thus no longer
emitted.
After prolonged idling or driving at very
low speeds, you may occasionally no-
tice water vapour being emitted from
the exhaust when accelerating. This is
of no consequence to the running of
the vehicle or to the environment.
If there is risk of clogging, a mes-
sage appears on the instrument
panel display, accompanied by an
audible signal and lighting of the
service warning lamp.
This alert tells you that the particle
fi l t e r i s s t a r t i n g t o fi l l u p ( i n c o n d i -
tions of urban driving of excep-
tionally long duration: low speeds,
t r a f fi c j a m s e t c . ) .
T o r e g e n e r a t e t h e fi l t e r , i t i s a d v i s e d to drive as soon as possible, when
t r a f fi c c o n d i t i o n s p e r m i t , a t a s p e e d
of 40 mph (around 60 km/h) or
m o r e f o r a t l e a s t fi v e m i n u t e s ( u n t i l
the alert message disappears).
If this alert persists, consult a
CITROËN dealer.
Refer to the Maintenance and
Warranty Guide for details of
the replacement interval for this
component.
Page 189 of 314
XI
!
1 7 0
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB Headlamps
Model with Xenon headlamps (D1S)
1. Sidelamps: W 5 W
2. Dual-function Xenon
headlamps (dipped/main): D1S
3. Cornering
lighting: HP19
4. Daytime running lamps: H P 2 4
F o r t h e m a i n t e n a n c e o f t h e f r o n t
h e a d l a m p u n i t a n d t h e c h a n g i n g o f
H P 1 9 , D 1 S a n d H P 2 4 b u l b s , c o n t a c t a C I T R O Ë N d e a l e r .
Risk of electrocution
X e n o n b u l b s m u s t b e r e p l a c e d b y a
C I T R O Ë N d e a l e r .
You are advised to change both
D 1 S b u l b s a t t h e s a m e t i m e , i f o n e
o f t h e m h a s f a i l e d .
T h e h e a d l a m p s a r e fi t t e d w i t h
p o l y c a r b o n a t e g l a s s w i t h a
p r o t e c t i v e c o a t i n g :
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,
u s e a s p o n g e a n d s o a p y w a t e r ,
w h e n u s i n g a h i g h p r e s s u r e
w a s h e r o n p e r s i s t e n t m a r k s , d o
n o t d i r e c t a t t h e l a m p s o r t h e i r
o u t l i n e s f o r t o o l o n g , s o a s n o t t o
d a m a g e t h e i r p r o t e c t i v e c o a t i n g
a n d s e a l s .
D o n o t t o u c h t h e b u l b d i r e c t l y
w i t h y o u r fi n g e r s , u s e l i n t - f r e e
c l o t h s .
Changing a halogen bulb should
o n l y b e d o n e a f t e r t h e h e a d l a m p
has been switched off for a few
m i n u t e s ( r i s k o f s e r i o u s b u r n s ) .
I t i s i m p e r a t i v e t o u s e o n l y a n t i - u l t r a -
v i o l e t ( U V ) t y p e b u l b s i n o r d e r n o t t o
d a m a g e t h e h e a d l a m p .
Page 190 of 314
XI
171
P R A C T I C A L I N F O R M A T I O N
Main beams
R e m o v e t h e p r o t e c t i v e c a p A .
D i s e n g a g e t h e r e t a i n i n g s p r i n g .
R e m o v e t h e b u l b a n d r e p l a c e i t ,
p a y i n g a t t e n t i o n t o t h e d i r e c t i o n
o f fi t t i n g .
R e fi t t h e r e t a i n i n g s p r i n g .
R e fi t t h e p r o t e c t i v e c a p A .
Model with halogen headlamps
1. Main beams: H1
2. Sidelamps: W 5 W
3. Dipped beams: H7
4. Directional lighting: H7
5. Daytime running lamps: H P 2 4
F o r t h e m a i n t e n a n c e o f t h e f r o n t
h e a d l a m p u n i t a n d c h a n g i n g H P 2 4
b u l b s , c o n t a c t a C I T R O Ë N d e a l e r .
Sidelamps
R e m o v e t h e p r o t e c t i v e c a p A .
P u l l t h e b u l b h o l d e r t o r e m o v e i t .
R e p l a c e t h e b u l b a n d r e fi t t h e
b u l b h o l d e r .
R e fi t t h e p r o t e c t i v e c a p A .
Page 199 of 314
XI
179
P R A C T I C A L I N F O R M A T I O N
Interior lamps
Roof lamps
U n c l i p t h e t r a n s p a r e n t c o v e r o f
t h e r o o f l a m p t o r e a c h t h e b u l b .
Bulb: W 5 W
Rear reading lamps (Tourer)
Detach the cover of the reading
l a m p t o a c c e s s t h e b u l b .
Bulb: W 5 W
Map reading lamp
D e t a c h t h e c o v e r .
I f n e c e s s a r y , d e t a c h t h e p a r t i t i o n
o f t h e a f f e c t e d m a p r e a d i n g l a m p . Boot lamp
Detach the cover and use a
W 5 W b u l b .
Pavement lighting
D e t a c h t h e c o v e r a n d u s e a W 5 W
b u l b . Floor lighting
D e t a c h t h e c o v e r a n d u s e a W 5 W
b u l b .
Glovebox
D e t a c h t h e c o v e r a n d u s e a W 5 W
b u l b .