2009.5 Citroen C5 fuel
[x] Cancel search: fuelPage 52 of 314
III
53
C O M F O R T
When starting with the engine
c o l d , a i r fl o w w i l l r e a c h i t s o p t i -
mum level gradually to prevent an
excessive distribution of cold air.
When entering the vehicle after it
has been parked for a fairly long
period, if the interior temperature
is very different from your comfort
setting there is no need to change
the temperature displayed in or-
der to quickly reach the level of
comfort required. The system
automatically uses its maximum
performance to correct the differ-
ence in temperature as quickly as
possible.
The water resulting from the air
conditioning condensation is dis-
charged via an opening provided
for this purpose; therefore, a pud-
dle of water may form underneath
the vehicle when stationary.
In all seasons, if the weather is
cool, the air conditioning is use-
ful as it removes the humidity
from the air and the condensa-
tion. Avoid driving for prolonged
periods with the air conditioning
switched off.
9. Front demisting - defrosting
In certain cases, the
"AUTO" mode may not
b e s u f fi c i e n t t o d e m i s t o r
defrost the windows (hu-
midity, several passen-
gers, ice).
Press control 9 to clear the win-
dows quickly. The indicator lamp
comes on.
This system controls the temperature,
a i r fl o w a n d i n t a k e a n d d i s t r i b u t e s t h e
ventilation to the windscreen and front
side windows.
Resuming manual control exits from
the "Demisting" mode. It must be
cancelled as soon as possible to
permit renewal of the air in the pas-
senger compartment and demisting.
Pressing one of the controls 1a and
1b returns the system to the "AUTO"
mode.
8. Rear demisting - defrosting
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current con-
sumption reduces fuel consumption.
The heated rear screen
operates independently
of the air conditioning
system.
Press control 8 , with the en-
gine running, to demist the rear
screen and the mirrors. The indi-
cator lamp comes on.
Demisting is switched off automati-
cally to avoid excessive consump-
tion of current and depending on the
exterior temperature.
It may be stopped by pressing con-
trol 8 again or when the engine is
switched off.
In this latter case, the demisting re-
sumes if the engine is switched on
again within one minute.
Page 56 of 314
III
!
57
C O M F O R T
Changing the battery
The remote control is supplied by a
6 V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below. Always switch off the program-
m a b l e h e a t i n g w h i l e fi l l i n g w i t h
f u e l t o a v o i d a n y r i s k o f fi r e o r e x -
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with an
exhaust gas extraction system.
Do not park the vehicle on an
i n fl a m m a b l e s u r f a c e ( d r y g r a s s ,
dead leaves, paper…), there is a
r i s k o f fi r e .
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
q u a n t i t y o f f u e l r e m a i n i n g i s s u f fi -
cient. If the fuel tank is at the re-
serve, we strongly advise that you
do not programme the heating.
Do not discard the used bat-
teries, take them to an ap-
proved collection point.
Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK" is displayed on the re-
mote control screen.
If a problem occurs, the message
"FAIL" appears. Repeat the operation.
In addition, your programmable
heating can be used to pre-heat
your vehicle’s passenger com-
partment. The interior volumetric protection
alarm movement sensor may be
d i s t u r b e d b y t h e fl o w o f a i r f r o m
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.
Page 85 of 314
IV
82
O P E N I N G S
FUEL TANK
Capacity of the tank: approximately
71 litres.
Low fuel level
When the minimum level
in the tank is reached, this
warning lamp comes on
in the instrument panel,
accompanied by an audible warning
and a message on the multifunction
s c r e e n . W h e n i t fi r s t c o m e s o n , t h e r e
remains around 5 litres of fuel in the
tank.
You must refuel to avoid running out
of fuel.
Press at the top left corner, then
pull open from the left.
turn the key a quarter turn to lock
a n d u n l o c k t h e fi l l e r c a p ,
when refuelling, place the cap on
hook A ,
fi l l t h e t a n k , b u t do not persist
after the third cut-off ; this could
cause your vehicle to malfunc-
tion.
While you are refuelling, the engine
must be stopped and the ignition
switched off.
For a petrol engine with a catalytic
converter, unleaded fuel is compul-
sory.
Opening the fuel flap Additions of fuel must be of at least
5 litres to be taken into account by
the fuel gauge.
T h e fi l l e r n e c k i s n a r r o w e r t o e n -
sure that only unleaded petrol
nozzles can be put in.
O p e n i n g t h e fi l l e r c a p m a y c r e a t e
a noise of an inrush of air. This
vacuum, which is entirely normal,
is caused by the sealing of the fuel
system.
Refuelling
Page 86 of 314
IV
83
O P E N I N G S
Quality of the fuel used for
petrol engines
The petrol engines are perfectly
compatible with E10 type petrol
biofuels (containing 10 % ethanol),
conforming to European standards
EN 228 and EN 15376.
E85 type fuels (containing up to 85 % ethanol) are reserved exclusively for
vehicles marketed for the use of this
type of fuel (BioFlex vehicles). The
quality of the ethanol must comply
with European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing
up to 100 % ethanol (E100 type). Quality of the fuel used for
Diesel engines
The Diesel engines are perfectly
compatible with biofuels which con-
form to current and future European
standards (Diesel fuel which com-
plies with standard EN 590 mixed
with a biofuel which complies with
standard EN 14214) available at the
pumps (containing up to 7 % Fatty
Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this
use is subject to strict application
of the special servicing conditions.
Consult a CITROËN dealer.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or di-
luted, domestic fuel...) is strictly pro-
hibited (risk of damage to the engine
and fuel system).
Page 171 of 314
X
153
C H E C K S
BLEEDING THE DIESEL FUEL FILTER
Protective cover
Removal of the cover Bleeding water from the fuel
filter
Bleed regularly (at each oil change).
To bleed the water, slacken the bleed
screw or the water in diesel fuel sen-
s o r , l o c a t e d a t t h e b a s e o f t h e fi l t e r .
Continue until all the water has
fl o w e d o u t .
Then retighten the bleed screw or
the water detection sensor.
HDi 110, HDi 163 and V6 HDi 240
engines
Pull the protective cover upwards
to remove it.
HDi 140 engine
Remove the protective cover by fi r s t u n c l i p p i n g a t 3 , then 1 and 4.
Unclip at 2 by pulling towards you,
then lift up.
R e fi t t i n g
Firstly clip in at 2 .
Lower and centre the cover.
Clip in at 3 and 4 , pushing verti-
cally and gently from the rear.
Clip in at 1 pushing vertically.
Page 172 of 314
X
!
154
C H E C K S
RUNNING OUT OF FUEL (DIESEL)
HDi 110 engine
Unclip the protective cover to gain
access to the priming pump. HDi 140 and HDi 163 engines
Unclip the protective cover to gain
access to the priming pump.
Priming the fuel system
In the event of running out of fuel:
a f t e r fi l l i n g ( m i n i m u m 5 l i t r e s )
and removing the protective cov-
er, operate the manual priming
pump, until some resistance is
felt,
operate the starter motor while
depressing the accelerator pedal
slightly until the engine starts. HDi engines make use of ad-
vanced technology.
All maintenance and repairs require
s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a
CITROËN dealer can guarantee.
V6 HDi 240 engine with electric
pump
In the event of running out of fuel:
after adding fuel, turn the ignition
key to position M , wait for a few
seconds,
operate the starter motor until
the engine starts.
If the engine fails to start after several
attempts, contact a CITROËN dealer.
I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t
a t t e m p t , w a i t fi f t e e n s e c o n d s b e f o r e
trying again.
If the engine fails to start after a few
attempts, operate the priming pump
again and then try to start the engine.
When the engine is idling, accelerate
slightly to complete the bleeding of
the circuit.
Page 175 of 314
X
!
157
C H E C K S
DIESEL ENGINES
The various caps and covers allow
a c c e s s f o r c h e c k i n g fl u i d l e v e l s , f o r
replacing certain components and
for priming the fuel system.
1. Screenwash and headlamp wash
reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r , d e p e n d i n g o n
equipment.
3. Engine coolant reservoir.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. B r a k e fl u i d r e s e r v o i r .
8. Battery.
As the Diesel fuel system op-
erates under high pressure,
any work on the fuel system
is prohibited.
V e h i c l e s fi t t e d w i t h t h e HDi 140 en-
g i n e m a y b e fi t t e d w i t h m e t a l s p r i n g s . In this case, a different power steer-
i n g fl u i d r e s e r v o i r i s fi t t e d .
HDi 110
HDi 140
Page 176 of 314
X!
158
C H E C K S
HDi 163 - V6 HDi 240 engines
(with particle filter)
1. Screen wash and headlamp
wash reservoir.
2. Power steering and suspension
fl u i d r e s e r v o i r .
3. Engine coolant reservoir.
4. Engine oil dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. A i r fi l t e r .
7. B r a k e fl u i d r e s e r v o i r .
8. Battery.
9. "+" and "-" terminals for starting
with a slave battery.
As the Diesel fuel system op-
erates under high pressure:
- Any work on the fuel system is prohibited.
- HDi engines make use of ad- vanced technology.
All maintenance and repairs re-
q u i r e s p e c i a l q u a l i fi c a t i o n s w h i c h
only a CITROËN dealer can guar-
antee.
HDi 163
V6 HDi 240