2009.5 Citroen C5 DAG warning light
[x] Cancel search: warning lightPage 112 of 306
VIII
112
S A F E T Y
TYRE UNDER-INFLATION DETECTION
S y s t e m w h i c h a u t o m a t i c a l l y c h e c k s t h e
p r e s s u r e s o f t h e t y r e s w h i l e d r i v i n g . Tyres OK display
Choice of detection
T h i s f u n c t i o n p r o v i d e s w a r n i n g o f t y r e s
t h a t a r e u n d e r - i n fl a t e d o r p u n c t u r e d .
Automatic detection
S e n s o r s m o n i t o r t h e t y r e p r e s s u r e s .
I n t h e e v e n t o f a n a n o m a l y , a m e s -
s a g e w i l l a p p e a r o n t h e i n s t r u m e n t
panel screen.
Driver request detection
Y o u c a n c h e c k t h e t y r e p r e s s u r e s a t
a n y t i m e .
P r e s s o n b u t t o n A (CHECK); the
i n f o r m a t i o n w i l l b e d i s p l a y e d o n
t h e i n s t r u m e n t p a n e l s c r e e n .
P r e s s o n b u t t o n A (CHECK).
T h e s y s t e m i n d i c a t e s t o y o u t h a t t h e
t y r e s a r e c o r r e c t l y i n fl a t e d .
T h i s i n f o r m a t i o n i s o n l y a v a i l a b l e o n
t h e r e q u e s t b y t h e d r i v e r . Under-inflated tyre
automatic detection
detection on request
Automatic detection:
A m e s s a g e i n d i c a t e s w h i c h t y r e i s
u n d e r - i n fl a t e d .
Driver request detection:
T h e v e h i c l e o u t l i n e i n d i c a t e s t h e u n -
d e r - i n fl a t e d t y r e ( s ) .
T h e m e s s a g e i s a c c o m p a n i e d b y
lighting of the SERVICE warning
l a m p a n d a n a u d i b l e b e e p .
C h e c k t h e t y r e p r e s s u r e s a s
soon as possible.
Page 124 of 306
IX
!
123
D R I V I N G
MANUAL PARKING BRAKE
Mechanical device for immobilising
the vehicle when stationary. This warning lamp comes
on if the parking brake is en-
gaged or not fully released.
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning lamp
i n d i c a t e s t h a t t h e b r a k e fl u i d l e v e l
is low or a malfunction of the brake
force distributor.
It is essential to stop the vehicle.
Consult a CITROËN dealer.
Application
Pull the parking brake lever up to
immobilise your vehicle.
To facilitate the action on the lever,
you are recommended to press the
brake pedal at the same time.
In all circumstances, as a pre-
cautionary measure, engage
fi r s t g e a r .
On steep gradients, turn the steer-
ing wheel towards the pavement. Release
Press on the end of the lever
whilst pulling it then lower it fully.
Page 125 of 306
IX!!
124
D R I V I N G
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake
is automatically applied
when the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y :
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobil-
ise the vehicle you need to manually
apply the parking brake by pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message "hand-
brake on" on the instrument pan-
el screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m
to you the application/release of
your electric parking brake. - the lighting of warning
lamp P on control A and
on the instrument panel,
- the display of a message "hand- brake on" on the instrument pan-
el screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Page 126 of 306
IX!
!
125
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox ( fi r s t
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the acce-le-
rator pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "hand- brake off" on the instrument pan-
el screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of
the automatic functions *
Automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
s c r e e n c o n fi g u r a t i o n m e n u . S e l e c t
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
Deactivation of the automatic
functions is recommended
in very cold weather (freezing)
and when towing (recovery, cara-
van...). Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply
the parking brake whether the engine
is running or off,
pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "hand- brake on" on the instrument pan-
el screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and a
message displayed if the parking
brake has not been applied.
* Depending on country.
Page 127 of 306
IX!
!
125
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox ( fi r s t
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the acce-le-
rator pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
- the display of a message "hand- brake off" on the instrument pan-
el screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of
the automatic functions *
Automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
s c r e e n c o n fi g u r a t i o n m e n u . S e l e c t
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
Deactivation of the automatic
functions is recommended
in very cold weather (freezing)
and when towing (recovery, cara-
van...). Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply
the parking brake whether the engine
is running or off,
pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
- the display of a message "hand- brake on" on the instrument pan-
el screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and a
message displayed if the parking
brake has not been applied.
* Depending on country.
Page 129 of 306
IX
!
127
D R I V I N G
Dynamic emergency braking
In the event of a failure of the vehi-
cle’s main braking system or in an
exceptional situation (e.g. driver tak-
en ill, under instruction, etc) pull and
hold control A to stop the vehicle.
The electronic stability programme
( E S P ) p r o v i d e s s t a b i l i t y d u r i n g d y -
namic emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel display:
- "Parking brake faulty".
- "Parking brake control faulty". I f a f a i l u r e o f t h e E S P s y s -
tem is signalled by the light-
ing of this warning lamp,
then braking stability is not
guaranteed. In this event, stability
must be assured by the driver by
repeating alternate "pull release" ac-
tions on control A .
The dynamic emergency
braking must only be used in
exceptional circumstances. Emergency parking brake
release
In the event of the electric parking
brake failing to release, an emer-
gency device can be used to release
the parking brake manually, provid-
ed that it is possible to immobilise
the vehicle while the procedure is
carried out.
If you can start the vehicle: with
the engine running, immobilise
the vehicle by applying the foot
brake while the operation is be-
ing carried out.
If you are unable to start the ve-
h i c l e ( fl a t b a t t e r y f o r e x a m p l e ) : d o
not use this device and contact
a CITROËN dealer. However, if
y o u a r e o b l i g e d t o p r o c e e d , fi r s t
immobilise your vehicle securely
and then follow the instructions
below.
Page 132 of 306
IX
130
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the follow-
ing warning lamps:
a n d / o r fl a s h i n g - The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
Pull the control lever for at least 5 seconds or until maximum
application.
S w i t c h o n t h e i g n i t i o n a n d c h e c k t h a t t h e e l e c t r i c p a r k i n g b r a k e
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
S w i t c h o n t h e i g n i t i o n .
Push the control lever and hold it for approximately 3 seconds.
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
a n d / o r fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
Wait approximately 3 minutes.
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault
- Lighting of the battery warning lamp makes it essential
to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switch ing off the engine.
Page 143 of 306
IX
141
D R I V I N G
In the event of a steep descent or
under excessive acceleration, the
speed limiter (which does not act
on the brakes) may not be able to
prevent the vehicle from exceeding
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
of-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed dis-
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
to return below the maximum speed,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
cle from exceeding the programmed
speed (e.g. on a steep descent or
under excessive acceleration).
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed. Return to normal driving
Either press on button 5 .
Or select the speed limiter func-
tion.
Or stop the engine.
Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.