2009.5 Citroen C3 PICASSO ECU

i
i
i
50
COMFORT Fully-folded position Flaps behind the rear seats

 Move the corresponding front seat
forward if necessary.

 Place the head restraints in the low
position.

 Pull control A , to release the seat
back which folds easily onto the
seat cushion.
This manoeuvre automatically retracts the seat cushion.
The seat fi ts into the fl oor, providing a
continuous level fl oor.
To put the seat back in position:

 Pull the seat back backwards until it
locks in place.

 Return the seat cushion to the de-
sired position. Flaps
B fi tted to the back of the rear
seat close the boot fl oor when the rear
seats are in the forward position.
Pull on the upper section of the fl aps to
release them.
They then provide a continuous level
fl oor.
Adjusting the head restraints
The 1/3 - 2/3 rear seat is fi tted with head
restraints.
They have a high position (for comfort
and safety) and a low position (for rear
visibility).
They may be removed, as follows:

 pull the head restraint upwards as
far as possible,

 then, press on the lug A .
When you are carrying rear pas-
sengers, never drive with the head
restraints removed. They must be
secured in place in the high position. When putting back in position,
take care not to jam the seat
belts. Ensure that they are correctly fi xed
to the seat back before any ma-
noeuvre.
Each fl ap is fi xed to the rear of
the seat by two removable plastic
clips.
To detach the fl aps from the rear
of the seat back, press fi rmly down
on the upper part of the two plastic
clips to release them.
To avoid risk of breakage, they dis-
engage if subjected to excessive
force.

!
77
FITTINGS
To avoid any risk of jamming of the
pedals:
- only use mats which are suited to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of another.
MATS
Removable carpet protection. Refitting
To refi t the mat on the driver's side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured cor-
rectly.
Fitting
When fi tting the mat for the fi rst time,
on the driver's side use only the fi xings
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:

 move the seat as far back as pos-
sible,

 unclip the fi xings,

 remove the mat.
TICKET HOLDER
It is located at the top of the dashboard
central panel.
It can be used to hold toll or parking
tickets.

!
77
FITTINGS
To avoid any risk of jamming of the
pedals:
- only use mats which are suited to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of another.
MATS
Removable carpet protection. Refitting
To refi t the mat on the driver's side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured cor-
rectly.
Fitting
When fi tting the mat for the fi rst time,
on the driver's side use only the fi xings
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:

 move the seat as far back as pos-
sible,

 unclip the fi xings,

 remove the mat.
TICKET HOLDER
It is located at the top of the dashboard
central panel.
It can be used to hold toll or parking
tickets.

81
FITTINGS
Boot fittings

1. Storage net on right-hand boot trim.

2. Open storage compartments.

3. Torch.

4. Removable boot fl oor.

5. Carrier bag hook .

6. Securing rings.

7. Storage area under boot carpet .

8. Rear parcel shelf.

i
82
FITTINGS
2-position adjustable boot
The movable boot fl oor with two posi-
tions allows you to:
- maximise the volume of the boot,
- partition the boot (storing of the rear shelf...),
- obtain a fl at fl oor from the boot opening to the front seats, when the
rear bench seat is in the retracted
position. Placing the movable boot fl oor in
the low position

 Press to release the handle located
at the boot opening.

 Unlock the movable boot fl oor by lift-
ing the handle.

 Manoeuvre the movable boot fl oor
rearwards, then downwards, using
the handle, following the slides on
the sides.

 Lock it by folding down the handle. Placing the movable boot fl oor in
the high position

 Press to release the handle.

 Unlock the movable boot fl oor by lifting
the handle.

 Use the handle to manoeuvre the
movable boot fl oor rearwards, then
upwards to its high position.

 Lock it by folding down the handle.
In the high position, the movable boot
fl oor permits storing of the rear shelf
and fragile objects.
The movable boot fl oor is fi tted with four
stowing rings to secure your loads using
the net available as an accessory.
Ensure that your boot is empty
before handling the movable boot
fl oor.

83
FITTINGS
Hooks
The hooks can be used to hold shop-
ping bags. Rear parcel shelf
This consists of three sections.
The front section is fl exible, and the
central and rear sections are rigid.
The rear section is secured to the tail-
gate by two cords.
To remove it from the boot:

 unhook the two cords,

 gently lift up the cover to remove it
from its fi xings,

 remove the cover.
It can be stored under the movable boot
fl oor, if this is in its high position.

86
INSTALLING CHILD SEATS ATTACHED USING THE SEAT BELT
In accordance with European regulations, this table indicates the options for installing child seats secured using a seat b elt
and universally approved (a) in accordance with the weight of the child and the seat in the vehicle.

a: Universal child seat: child seat that can be installed in all vehicles using a seat belt.

b: Group 0: from birth to 10 kg. Shells seats and baby carriers canno t be installed in the front passenger seat.

c: Consult the legislation in force in your country before inst alling your child on this seat.

U: Seat suitable for the installation of a child seat secure d using a seat belt and universally approved, "rearwards-facing"
and/or "forwards-facing".

X: Sear position not suitable for installation of a child se at for the weight class indicated.
CITROËN recommends that children travel in the rear seats, with the rear seats in the fully back position.

Weight of the child and indicative age

Seat
Under 13 kg
(groups 0 ( b )
and 0+)
Up to approx 1 year
From 9 to 18 kg
(group 1)
1 to 3 years approx
From 15 to 25 kg
(group 2)
3 to 6 years approx
From 22 to 36 kg
(group 3)
6 to 10 years approx
Front passenger
seat ( c )
U U U U
Rear outer seats
U U U U
Rear centre seat
X X X X

i
89
This ISOFIX mounting system guaran-
tees reliable, safe and fast fi tting of the
child seat in your vehicle.
The ISOFIX child seats are fi tted with
two locks which are secured easily on
these rings A .
Some also have a top
tether
belt which
can be attached to ring B .
To attach this belt, raise the head re-
straint of the seat, then pass the buckle
between the rods. Then fi x the buckle
on ring B , then tension the top tether
belt.
If a child is not installed in a vehicle cor-
rectly, the child's protection in the event
of a collision will be compromised.
To know which ISOFIX child seats can
be installed in your vehicle, see the ta-
ble of seating positions for ISOFIX child
seats.
The rear seats must be in the fully back
position to install ISOFIX seats.
This child seat can also be used on seats which are not fi tt ed with ISOFIX
mountings. In this case, it must be attached to the vehicle se at using the
three point seat belt.

Follow the instructions for fi tting the child seat given in the seat manu-
facturer's installation guide. ISOFIX CHILD SEAT RECOMMENDED BY CITROËN AND APPROVED FOR YOUR VEHICLE

RÖMER Duo Plus ISOFIX (size category B1 )

Group 1: from 9 to 18 kg
Installed in the forwards-facing position.
Fitted with an upper strap to be secured on the upper ring B , referred to as the TOP TETHER.
Three seat body angles: sitting, reclining, lying.