2009.5 Citroen C3 PICASSO boot

80
FITTINGS Opening

 Lower the storage shelf.

 Press the fl ap opening control.

 Lower the fl ap.

 Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
When unfolded, this provides a storage
area split into 2 sections, completing
the storage spaces available at the rear
of the vehicle.
Storage tray

80
FITTINGS Opening

 Lower the storage shelf.

 Press the fl ap opening control.

 Lower the fl ap.

 Load the objects from inside the
boot.
Ski flap
Device for storing and transporting long
objects.
When unfolded, this provides a storage
area split into 2 sections, completing
the storage spaces available at the rear
of the vehicle.
Storage tray

81
FITTINGS
Boot fittings

1. Storage net on right-hand boot trim.

2. Open storage compartments.

3. Torch.

4. Removable boot fl oor.

5. Carrier bag hook .

6. Securing rings.

7. Storage area under boot carpet .

8. Rear parcel shelf.

i
82
FITTINGS
2-position adjustable boot
The movable boot fl oor with two posi-
tions allows you to:
- maximise the volume of the boot,
- partition the boot (storing of the rear shelf...),
- obtain a fl at fl oor from the boot opening to the front seats, when the
rear bench seat is in the retracted
position. Placing the movable boot fl oor in
the low position

 Press to release the handle located
at the boot opening.

 Unlock the movable boot fl oor by lift-
ing the handle.

 Manoeuvre the movable boot fl oor
rearwards, then downwards, using
the handle, following the slides on
the sides.

 Lock it by folding down the handle. Placing the movable boot fl oor in
the high position

 Press to release the handle.

 Unlock the movable boot fl oor by lifting
the handle.

 Use the handle to manoeuvre the
movable boot fl oor rearwards, then
upwards to its high position.

 Lock it by folding down the handle.
In the high position, the movable boot
fl oor permits storing of the rear shelf
and fragile objects.
The movable boot fl oor is fi tted with four
stowing rings to secure your loads using
the net available as an accessory.
Ensure that your boot is empty
before handling the movable boot
fl oor.

83
FITTINGS
Hooks
The hooks can be used to hold shop-
ping bags. Rear parcel shelf
This consists of three sections.
The front section is fl exible, and the
central and rear sections are rigid.
The rear section is secured to the tail-
gate by two cords.
To remove it from the boot:

 unhook the two cords,

 gently lift up the cover to remove it
from its fi xings,

 remove the cover.
It can be stored under the movable boot
fl oor, if this is in its high position.

i
120
PRACTICAL INFORMATION
CHANGING A WHEEL
The tools are installed under the boot
fl oor.
For access to them:

 open the boot,

 remove the boot fl oor,

 lift up the boot carpet,

 remove the box containing the
tools,

 remove the polystyrene storage box. All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.

1. Wheelbrace.
For removal of the wheel trim and removal of the wheel fi xing bolts.

2. Jack with integral handle.
For raising the vehicle.

3. "Bolt cover" tool.
For removal of the bolt protectors (covers) on alloy wheels.
List of tools
Other accessories

6. Removable towing eye.
Refer to the paragraph "Towing the
vehicle".
Access to the tools
Wheel with trim

When removing the wheel , fi rst
detach the trim using the wheel-
brace 1 pulling at the valve pas-
sage hole.

When refi tting the wheel , refi t the
trim starting by placing its notch fac-
ing the valve and press around its
edge with the palm of your hand.

4. Centring guide.
For refi tting an alloy wheel to the hub.

5. Socket for the security bolts
(located in the glove box).
For adaptating the wheelbrace to the special "security" bolts.
Procedure for changing a faulty wheel
for the spare wheel using the tools
provided with the vehicle.

i
121
PRACTICAL INFORMATION
Fitting the steel or "space-
saver" type spare wheel
If your vehicle is fi tted with alloy
wheels, it is normal to notice, when
tightening the bolts on fi tting, that
the washers do not come into con-
tact with the steel or "space-saver"
type spare wheel. The wheel is
secured by the conical contact of
each bolt.
Access to the spare wheel
The spare wheel is installed in the boot
under the fl oor.
According to country, the spare wheel
may be steel or of the "space-saver"
type.
For access to it, refer to the paragraph
"Access to tools" on the previous page.
Taking out the wheel

 Unscrew the yellow central bolt, and
remove it.

 Raise the spare wheel towards you
from the rear.

 Take the wheel out of the boot.
Putting the wheel back in place

 Put the wheel back in its housing.

 Refi t the yellow central bolt in the
centre of the wheel.

 Tighten fully until the central bolt
clicks to retain the wheel correctly.

 Put the polystyrene storage box
back in place.

 Put the box back in place and clip it.

PRACTICAL INFORMATION
Changing foglamp/reversing lamp
bulbs

 open the boot,


press on the tabs using 2 screwdrivers,

 disconnect the lamp connector,

 turn the bulb holder by a quarter turn,

 remove the bulb and replace it.
To refi t, carry out these operations in
reverse order. Changing the third stop lamp bulbs
(4 x W5W bulbs)

 open the boot,

 remove the two plugs located on the
boot inner panel,

 press on the body of the lamp with
2 screwdrivers to remove it from its
housing,

 turn the corresponding bulb-holder
a quarter turn,

 pull the bulb and replace it.
To refi t, carry out these operations in
reverse order. Changing the number plate lamp
bulbs (W5W)

 insert a thin screwdriver into one of
the lens’ exterior holes,

 push it outwards to unclip.

 remove the lens.

 pull the bulb and replace it.
To refi t, carry out these operations in
reverse order.