2009.5 Citroen C3 PICASSO DAG seats
[x] Cancel search: seatsPage 36 of 200
49
COMFORT
FRONT SEATS
Seat consisting of a seat cushion, a seat
back and a head restraint which can all
be adjusted to adapt your position for
ease of driving and comfort. D r i v e r ' s s e a t h e i g h t a d j u s t m e n t S e a t b a c k a n g l e a d j u s t m e n t
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Raise the control bar and slide the
seat forwards or backwards.
Pull the control lever upwards to raise
or push it downwards to lower, as
many times as necessary, to obtain
the position required.
Push the control rearwards.
Page 37 of 200
!
50
COMFORT
Press the control located under the
front end of the armrest to release it.
Move it to the low position.
Raise it notch by notch to reach the
desired position.
To place the armrest in the vertical posi-
tion, raise it and push it backwards be-
yond the point of resistance.
H e a d r e s t r a i n t h e i g h t a d j u s t m e n t
To raise the head restraint, pull it up-
wards.
To remove the head restraint, press
the lug A and pull the head restraint
upwards.
To put the head restraint back in
place, engage the head restraint
stems in the openings keeping them
in line with the seat back.
To lower the head restraint, press
the lug A and the head restraint at
the same time. T h e h e a d r e s t r a i n t i s fi t t e d w i t h a
frame with notches which prevents
it from lowering; this is a safety de-
vice in case of impact.
T h e a d j u s t m e n t i s c o r r e c t w h e n
t h e u p p e r e d g e o f t h e h e a d r e -
s t r a i n t i s l e v e l w i t h t h e t o p o f t h e
h e a d .
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
A d j u s t i n g t h e a r m r e s t
A d d i t i o n a l a d j u s t m e n t s
H e a t e d s e a t s c o n t r o l
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
With the engine running, the front seats
can be heated separately.
Page 38 of 200
!
COMFORT
T a b l e p o s i t i o n o f t h e f r o n t
p a s s e n g e r s e a t
D o n o t f o r g e t t o f o l d t h e " a i r c r a f t "
t y p e t a b l e fi x e d o n t h e b a c k o f t h e
s e a t fi r s t .
For safety reasons, a passenger
sat in the rear of the vehicle must
not place his feet on the front seat
in the table position.
Placing this seat in the table position,
with the rear benchseat also in the table
position, allows you to transport long
objects.
Push the control upwards and guide
the seat back forwards to fold it onto
the seat cushion.
To put it back in place, lift up the seat
back and guide it rearwards until it
locks in.
REAR SEATS
F o r w a r d s a n d b a c k w a r d s
a d j u s t m e n t A d j u s t i n g t h e s e a t b a c k a n g l e
Raise the control and slide the seat
forwards or backwards.
Each section (1/3 - 2/3) can be adjusted
individually.
The seat can be adjusted to 2 different
positions:
- a standard position,
- an angled (inclined) position.
To adjust the seat back:
Pull the control lever forwards.
Page 39 of 200
!
COMFORT
T a b l e p o s i t i o n o f t h e f r o n t
p a s s e n g e r s e a t
D o n o t f o r g e t t o f o l d t h e " a i r c r a f t "
t y p e t a b l e fi x e d o n t h e b a c k o f t h e
s e a t fi r s t .
For safety reasons, a passenger
sat in the rear of the vehicle must
not place his feet on the front seat
in the table position.
Placing this seat in the table position,
with the rear benchseat also in the table
position, allows you to transport long
objects.
Push the control upwards and guide
the seat back forwards to fold it onto
the seat cushion.
To put it back in place, lift up the seat
back and guide it rearwards until it
locks in.
REAR SEATS
F o r w a r d s a n d b a c k w a r d s
a d j u s t m e n t A d j u s t i n g t h e s e a t b a c k a n g l e
Raise the control and slide the seat
forwards or backwards.
Each section (1/3 - 2/3) can be adjusted
individually.
The seat can be adjusted to 2 different
positions:
- a standard position,
- an angled (inclined) position.
To adjust the seat back:
Pull the control lever forwards.
Page 40 of 200
i
i
i
52
COMFORT F u l l y - f o l d e d p o s i t i o n F l a p s b e h i n d t h e r e a r s e a t s
Move the corresponding front seat
forward if necessary.
Place the head restraints in the low
position.
Pull control A , to release the seat
back which folds easily onto the
seat cushion.
This manoeuvre automatically re- tracts the seat cushion.
T h e s e a t fi t s i n t o t h e fl o o r , p r o v i d i n g a
c o n t i n u o u s l e v e l fl o o r .
To put the seat back in position:
Pull the seat back backwards until it
locks in place.
Return the seat cushion to the de-
sired position. Flaps
B fi t t e d t o t h e b a c k o f t h e r e a r
s e a t c l o s e t h e b o o t fl o o r w h e n t h e r e a r
seats are in the forward position.
P u l l o n t h e u p p e r s e c t i o n o f t h e fl a p s t o
release them.
They then provide a continuous level
fl o o r .
A d j u s t i n g t h e h e a d r e s t r a i n t s
T h e 1 / 3 - 2 / 3 r e a r s e a t i s fi t t e d w i t h h e a d
restraints.
They have a high position (for comfort
and safety) and a low position (for rear
visibility).
They may be removed, as follows:
pull the head restraint upwards as
far as possible,
then, press on the lug A .
When you are carrying rear pas-
sengers, never drive with the head
restraints removed. They must be
secured in place in the high position. When putting back in position,
take care not to jam the seat
belts. E n s u r e t h a t t h e y a r e c o r r e c t l y fi x e d
to the seat back before any ma-
noeuvre.
E a c h fl a p i s fi x e d t o t h e r e a r o f
the seat by two removable plastic
clips.
T o d e t a c h t h e fl a p s f r o m t h e r e a r
o f t h e s e a t b a c k , p r e s s fi r m l y d o w n
on the upper part of the two plastic
clips to release them.
To avoid risk of breakage, they dis-
engage if subjected to excessive
force.
Page 65 of 200
!
i
70
VISIBILITY In fog or snow, the brightness
s e n s o r m a y d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lamps will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.
Linked with the "Guide-me-home"
lighting
Association with the automatic illumina-
tion of headlamps provides the "guide-
me-home" lighting with the following
additional options:
- automatic activation of "guide-me-
home" lighting when automatic illu-
mination of headlamps is switched
on (in the vehicle parameters of the
m u l t i f u n c t i o n s c r e e n c o n fi g u r a t i o n
m e n u ) ,
- selection of the duration of main- taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters of the multifunction screen
c o n fi g u r a t i o n m e n u ( e x c e p t f o r
monochrome
screen
A where this
i s p r e s e t ) .
Operating fault In the event of a malfunction
of the brightness sensor, the
lamps come on, this warn-
ing lamp is displayed on
the instrument panel and/or a message
appears on the multifunction screen,
accompanied by an audible signal.
Consult a CITROËN dealer.
HEADLAMP ADJUSTMENT
The initial setting is position "0" .
To avoid causing a nuisance to other
road users, the height of the halogen
headlamps should be adjusted accord-
ing the load in the vehicle.
0. 1 or 2 people in the front seats.
-. Less than 5 people.
1. 5 people.
-. 5 people + maximum authorised
load.
2 - 3. Driver + maximum authorised
load.
Page 66 of 200
!
i
70
VISIBILITY In fog or snow, the brightness
s e n s o r m a y d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lamps will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.
Linked with the "Guide-me-home"
lighting
Association with the automatic illumina-
tion of headlamps provides the "guide-
me-home" lighting with the following
additional options:
- automatic activation of "guide-me-
home" lighting when automatic illu-
mination of headlamps is switched
on (in the vehicle parameters of the
m u l t i f u n c t i o n s c r e e n c o n fi g u r a t i o n
m e n u ) ,
- selection of the duration of main- taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters of the multifunction screen
c o n fi g u r a t i o n m e n u ( e x c e p t f o r
monochrome
screen
A where this
i s p r e s e t ) .
Operating fault In the event of a malfunction
of the brightness sensor, the
lamps come on, this warn-
ing lamp is displayed on
the instrument panel and/or a message
appears on the multifunction screen,
accompanied by an audible signal.
Consult a CITROËN dealer.
HEADLAMP ADJUSTMENT
The initial setting is position "0" .
To avoid causing a nuisance to other
road users, the height of the halogen
headlamps should be adjusted accord-
ing the load in the vehicle.
0. 1 or 2 people in the front seats.
-. Less than 5 people.
1. 5 people.
-. 5 people + maximum authorised
load.
2 - 3. Driver + maximum authorised
load.
Page 78 of 200
FITTINGS
REAR INTERIOR FITTINGS
They are located on the back of the
front seats.
Two boxes are available, located under
the rear passenger footwells.
To open them, lift the lid using the cut-
out. There is a cup holder located at the rear
of the centre console.
Storage boxes Seat pockets Cup holder