2009.5 Citroen C3 PICASSO DAG display
[x] Cancel search: displayPage 104 of 200
!
!
102
If at least one of the two airbag
warning lamps come on continu-
ously, do not install a child seat on
the front passenger seat.
Have the system checked by a
CITROËN dealer.
Operating fault
If this warning lamp comes on on the instrument panel, accompa-
nied by an audible warning and
a message on the multifunction
screen, contact a CITROËN dealer to
have the system checked. The airbags
may no longer be triggered in the event
of a serious impact.
Reactivation
When you remove the child seat, turn
switch
1 to the "ON" position to reacti-
vate the airbag and so assure the safety
of your front passenger in the event of
an impact.
With the ignition on, this warn-
ing lamp comes on on the instru-
ment panel or on the seat belt
and passenger's front airbag
warning lamp display for approximately
one minute, if the passenger's front air-
bag is activated. To assure the safety of your child,
it is imperative that the passenger's
front airbag is deactivated when
you install a "rearwards-facing"
child seat on the front passenger
seat.
Otherwise, the child would risk be-
ing seriously injured or killed if the
airbag were triggered.
According to version, this warn-
ing lamp comes on either on
the instrument panel or on the
seat belt and passenger's front
airbag warning lamp display when the
ignition is on and until the airbag is re-
activated. I f t h i s w a r n i n g l a m p fl a s h e s ,
contact a CITROËN dealer.
The passenger's front airbag
may no longer be triggered in
the event of a serious impact.
Deactivation
Only the passenger's front airbag can
be deactivated:
with the ignition off , insert the key
in the passenger air bag disarming
switch 1 ,
turn it to the "OFF" position,
then, remove the key keeping the
switch in this position.
Page 109 of 200
i
106
DRIVING
SPEED LIMITER
System which prevents the vehicle from
exceeding the speed programmed by
the driver.
When the programmed speed limit is
reached, pressing the accelerator pedal in
the normal manner no longer has any effect.
The controls of this system are grouped
together on stalk A .
1. Speed limiter mode selection thumb
wheel
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button The programmed information is
grouped together on the instrument
panel screen.
5. Speed limiter on/off indication
6. Speed limiter mode selection indica-
tion
7. Programmed speed value
Steering mounted controls Displays on the instrumen
t panel
The speed limiter cannot, in any
circumstances, replace the need
to respect speed limits, nor can it
replace the need for vigilance and
responsibility on the part of the
driver.
The speed limiter is
switched on manu-
ally: it requires a programmed speed of
at least 20 mph (30 km/h).
The speed limiter is switched off by
manual operation of the control.
The programmed speed can be exceed-
ed temporarily by pressing the accelera-
t o r fi r m l y .
To return to the programmed speed,
simply slow down to a speed below the
programmed speed.
The programmed speed remains in the
memory when the ignition is switched
off.
Page 110 of 200
!
107
DRIVING
On a steep descent or in the event
of sharp acceleration, the speed
limiter will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi- tioned correctly,
- d o n o t fi t o n e m a t o n t o p o f a n - other.
Programming
Turn thumb wheel 1 to the "LIMIT"
position: the speed limiter mode
is selected but is not switched on
(PAUSE).
You do not have to switch the speed
limiter on in order to set the speed.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed
speed will not have any effect unless you press the pedal
fi r m l y past the point of resistance .
The speed limiter is deactivated temporarily and the pro-
g r a m m e d s p e e d , w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed, by means of intentional
or unintentional deceleration of the vehicle, automaticall y
c a n c e l s t h e fl a s h i n g o f t h e p r o g r a m m e d s p e e d .
Leaving limiter mode
Turn thumb wheel 1 to the "0" position: the speed limiter
mode is deselected. The display returns to the distance
recorder. Operating fault
In the event of a speed limiter malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have the system checked by a
CITROËN dealer.
Set the speed value by pressing button 2 or 3
(e.g.: 55 mph (90 km/h)).
You can then change the programmed speed using but tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Switch the speed limiter on by pressing button 4 .
Switch the speed limiter off by pressing button 4 : the dis-
p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( P A U S E ) .
Switch the speed limiter back on by pressing button 4
again.
Page 111 of 200
i
108
DRIVING
CRUISE CONTROL
System which automatically maintains
the speed of the vehicle at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is switched on
manually: it requires a minimum vehicle
speed of 25 mph (40 km/h) and the en-
gaging of at least 4th gear.
The controls of this system are grouped
together on control stalk A .
1. Cruise control mode selection dial
2. Speed programming/value decrease
button
3. Speed programming/value increase
button
4. Cruise control off/resume button The programmed information is
grouped together on the instrument
panel screen.
5. Cruise control off/resume indication
6. Cruise control mode selection indi-
cation
7. Programmed speed value
Steering mounted controls Displays on the instrumen
t panel
The cruise control cannot, in any
circumstances, replace the need to
respect speed limits, nor can it re-
place the need for vigilance and re-
sponsibility on the part of the driver.
The cruise control is switched off manu-
ally or by pressing the brake or clutch
pedal or on triggering of the ESP sys-
tem for safety reasons.
It is possible to exceed the programmed
speed temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
Page 112 of 200
!
109
DRIVING
When the cruise control is switched
on, be careful if you maintain the
pressure on one of the programmed
speed changing buttons: this may
result in a very rapid change in the
speed of your vehicle.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f fi c .
On a steep descent, the cruise
control will not be able to prevent
the vehicle from exceeding the pro-
grammed speed.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is posi- tioned correctly,
- n e v e r fi t o n e m a t o n t o p o f a n - other.
Programming
Turn dial 1 to the "CRUISE" posi-
tion: the cruise control mode is
selected but is not switched on
(PAUSE).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed
s p e e d r e s u l t s i n fl a s h i n g o f t h i s s p e e d o n t h e d i s p l a y .
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically ca n-
c e l s t h e fl a s h i n g o f t h e s p e e d .
Return to normal driving
Turn dial 1 to the "0" position: the cruise control mode is
deselected. The display returns to the distance rec order. Operating fault
In the event of a cruise control malfunc-
tion, the speed is cleared resulting in
fl a s h i n g o f t h e d a s h e s .
Have it checked by a CITROËN dealer.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
(e.g.: 70 mph (110 km/h)).
Switch off the cruise control by pressing button 4 : the
d i s p l a y c o n fi r m s t h a t i t h a s b e e n s w i t c h e d o f f ( P A U S E ) .
Switch the cruise control back on by pressing button 4
again.
You can then change the programmed speed using but
tons 2
and 3 :
- by + or - 1 mph (km/h) = short press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.
Page 156 of 200
152
0 1
1
5
1 0
2
3 4 6
1 3
1 1
9
1 4 1 5
7 8 1 2 1 6
1 . E n g i n e n o t r u n n i n g - Short press: on/off. - L o n g p r e s s : C D p a u s e , m u t e f o r t h e r a d i o . E n g i n e r u n n i n g - S h o r t p r e s s : C D p a u s e , m u t e f o r t h e r a d i o . - L o n g p r e s s : r e i n i t i a l i s a t i o n o f t h e s y s t e m .
2 . V o l u m e a d j u s t m e n t ( e a c h s o u r c e i s i n d e p e n d e n t , i n c l u d i n g a l s o n a v i g a t i o n m e s s a g e s a n d a l e r t s )
3 . A c c e s s t o t h e " R a d i o " M e n u . D i s p l a y t h e l i s t o f s t a t i o n s .
4 . A c c e s s t o t h e " M u s i c " M e n u . D i s p l a y t h e t r a c k s .
6 . A c c e s s t o t h e " P h o n e " M e n u . D i s p l a y t h e c a l l l i s t .
7 . A c c e s s t o t h e " M O D E " M e n u . Selection of the successive display of: R a d i o , M a p , N A V ( i f n a v i g a t i o n i s i n p r o g r e s s ) , T e l e p h o n e ( i f a c o n v e r s a t i o n i s i n p r o g r e s s ) , T r i p c o m p u t e r . L o n g p r e s s : d i s p l a y o f a b l a c k s c r e e n ( D A R K ) .
8 . A c c e s s t o t h e " N a v i g a t i o n " M e n u . D i s p l a y t h e l a s t d e s t i n a t i o n s .
9 . A c c e s s t o t h e " T r a f fi c " M e n u . D i s p l a y t h e c u r r e n t t r a f fi c a l e r t s .
1 0 . E S C : a b a n d o n t h e o p e r a t i o n i n p r o g r e s s .
1 1 . C D e j e c t .
1 2 . Selection of the previous/next radio station from the list. Selection of the previous/next MP3 directory. S e l e c t i o n o f t h e p r e v i o u s / n e x t p a g e o f a l i s t .
1 3 . Selection of the previous/next radio station. S e l e c t i o n o f t h e p r e v i o u s / n e x t C D o r M P 3 t r a c k . Selection of the previous/next line of a list.
1 4 . Buttons 1 to 6: Selection of the stored radio station. L o n g p r e s s : s t o r e t h e c u r r e n t r a d i o s t a t i o n .
1 5 . S D c a r d r e a d e r ( n a v i g a t i o n S D c a r d o n l y ) .
1 6 . D i a l f o r s e l e c t i o n o f t h e s c r e e n d i s p l a y a n d a c c o r d i n g t o t h e context of the menu S h o r t p r e s s : c o n t e x t u a l m e n u o r c o n fi r m a t i o n . L o n g p r e s s p r e s s : c o n t e x t u a l m e n u s p e c i fi c t o t h e l i s t displayed.
F I R S T S T E P S
M y W a y C O N T R O L P A N E L
3 - 4 . L o n g p r e s s : a c c e s s t o t h e a u d i o s e t t i n g s : f r o n t / r e a r a n d l e f t / r i g h t b a l a n c e , b a s s / t r e b l e , e q u a l i z e r , l o u d n e s s , a u t o m a t i c v o l u m e a d j u s t m e n t , i n i t i a l i s e t h e s e t t i n g s .
5 . Access to the "SETUP" Menu. L o n g p r e s s : a c c e s s t o t h e G P S c o v e r a g e a n d t h e demonstration mode.
Page 165 of 200
161
0 3
5
6
3
2
1
4
N A V I G A T I O N S E T T I N G S
Select "Set parameters for risk areas" t o g a i n a c c e s s t o t h e " D i s p l a y o n map", "Visual alert" and "Sound alert" functions.
S e l e c t t h e " P O I c a t e g o r i e s o n M a p " function to select the POIs to be displayed on the map by default.
Press the NAV button.
P r e s s t h e N A V b u t t o n a g a i n o r s e l e c t t h e N a v i g a t i o n M e n u f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
S e l e c t t h e " S e t t i n g s " f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
P O I C A T E G O R I E S O N M A P
S E T T I N G S
S E T P A R A M E T E R S F O R R I S K A R E A S
" N A V I G A T I O N " M E N U
N A V I G A T I O N - G U I D A N C E
Select the "Navi volume" function and turn the dial to set the volume of each v o i c e s y n t h e s i s e r ( t r a f fi c i n f o r m a t i o n , a l e r t m e s s a g e s … ) .
NAVI VOLUME
The adjustment of the volume for the Risk Areas P
OIs is used only d u r i n g t h e t r a n s m i s s i o n o f a n a l e r t .
U P D A T I N G T H E R I S K A R E A S P O I s
Contact a CITROËN dealer for the procedure to foll ow to obtain the R I S K A R E A P O I s . T h i s r e q u i r e s a n S D H C ( H i g h C a p a c i t y ) c o m p a t i b l e r e a d e r .
Page 167 of 200
163
0 4
2
1
3
2
1
P R I N C I P A L T M C S Y M B O L S
R e d a n d y e l l o w t r i a n g l e : t r a f fi c i n f o r m a t i o n , p a r
e x a m p l e :
B l a c k a n d b l u e t r i a n g l e : g e n e r a l i n f o r m a t i o n , f o r e x a m p l e :
With the current audio source displayed on the screen, press the dial.
T h e s h o r t c u t m e n u f o r t h e s o u r c e a p p e a r s a n d g i v e s a c c e s s t o : T h e s h o r t c u t m e n u f o r t h e s o u r c e a p p e a r s a n d g i v e s a c c e s s t o :
S e l e c t T r a f fi c A n n o u n c e m e n t s ( T A ) a n d p r e s s t h e d i a l t o c o n fi r m a n d g o t o t h e a s s o c i a t e d s e t t i n g s .
T h e T A ( T r a f fi c A n n o u n c e m e n t ) f u n c t i o n g i v e s p r i o r i t y t o T A a l e r t m e s s a g e s . T o o p e r a t e , t h i s f u n c t i o n n e e d s g o o d r e c e p t i o n o f a r a d i o s t a t i o n t r a n s m i t t i n g t h i s t y p e o f m e s s a g e . W h e n a t r a f fi c r e p o r t i s t r a n s m i t t e d , t h e c u r r e n t a u d i o s o u r c e ( R a d i o , C D , J u k e b o x , . . . ) i s i n t e r r u p t e d a u t o m a t i c a l l y t o p l a y t h e T A m e s s a g e . N o r m a l p l a y b a c k of the audio source resumes at the end of the transmission of the m e s s a g e .
R E C E I V I N G T A M E S S A G E S
TA