2009.5 Citroen C3 display

FAMILIARISATION
MONITORING
Instrument panel

A. With the ignition on, the fuel gauge
bars for the fuel remaining should
light up.

B. With the engine running, the associ-
ated low level warning lamp should
switch off.

C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the
level which is low.


 18 Warning lamps

1. With the ignition on, the orange and
red warning lamps come on.

2. With the engine running, these
warning lamps should switch off.
If a warning lamp remains on, refer to
the page concerned.


 20 Switch panel
Lighting of the indicator lamp indicates
the status of the corresponding func-
tion.

A. Activation of the electric child lock


 89
or
Deactivation of the interior volumetric alarm.
 59

B. Deactivation of the ESP/ASR system.
 92

FAMILIARISATION
Speed limiter "LIMIT"

1. Selecting/Switching off speed limiter
mode.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Speed limiter on/off.


 104
DRIVING SAFELY
Cruise control "CRUISE"

1. Selecting/Switching off cruise con-
trol mode.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Cruise control Off/Resume.


 106
The values must be set with the engine
running. Display in the instrument panel
The cruise control or speed limiter mode
appears on the instrument panel when
it is selected.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on a manual gearbox
(second gear on an automatic gear-
box). Cruise control
Speed limiter

1
INSTRUMENTS and CONTROLS
Panel grouping together the vehicle operation indication dials and warning lamps.
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS

5. Display management button
Servicing information.
Adjust the time and choose units.
Reset the service indicator.

6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For further information, refer
to the paragraph relating to the
button or function and its associ-
ated display.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Vehicle speed.
Indicates the current speed of the moving vehicle (mph or km/h).

3. Fuel level.
Indicates the quantity of fuel remain- ing in the tank.

4. Screen.
A. Ambient temperature.
(°Celsius or °Fahrenheit)

B. Gear change indicator.

C. Time.

D. Engine oil level indicator.
Appears a few seconds after switch- ing on the ignition, then disappears.

E. Trip computer.

F. Service indicator
(miles or km) then,
Total mileage.
These two functions are displayed successively when switching on the
ignition.
Screen

1
INSTRUMENTS and CONTROLS
PETROL - DIESEL MANUAL OR AUTOMATIC GEARBOX
INSTRUMENT PANELS
Panel grouping together the vehicle operation indication dials and warning lamps.
Depending on the version, the instrument panel may have permanent back-lighting.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Vehicle speed.
Indicates the current speed of the moving vehicle (km/h or mph).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Screen.
5. Display management button
Alternates display between range and trip mileage recorder.
Servicing information.
Resets the selected function to zero (trip distance recorder or service
indicator).

6. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
For further information, refer
to the paragraph relating to the
button or function and its associ-
ated display.
A. Speed limiter
(mph or km/h) or
Cruise control.

B. Gear change indicator.

C. Automatic gearbox information.

D. Range
(miles or km) or
Trip mileage recorder.

E. Service
indicator
(miles or km), then
Total mileage recorder
These two functions are displayed successively when switching on the
ignition

F. Engine oil level indicator
Appears a few seconds after switch- ing on the ignition, then disappears.
Screen

1
INSTRUMENTS and CONTROLS
Service indicator
System which informs the driver when the
next service is due, in accordance with
the manufacturer's servicing schedule.
The point at which the service is due is
calculated from the last indicator zero re-
set. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service. More than 600 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.

Example: 4 800 km remain before the
next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Less than 600 miles (1 000 km)
remain before the next service is due

Example: 400 miles (900 km) remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances. 5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation.
The spanner re-
mains on to indicate that a service
must be carried out soon.

1
INSTRUMENTS and CONTROLS
Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains lit .
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval. Service indicator zero reset
After each service, the maintenance in-
dicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance re-
corder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner dis-
appears. Retrieving the service information
You can access the service information
at any time.

 Press the trip distance recorder zero
reset button.
The service information is displayed for
a few seconds, then disappears. Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi ve minutes for the zero reset to
be taken into account.

1
INSTRUMENTS and CONTROLS
Service overdue
For 5 seconds after the ignition is
switched on, the spanner fl ashes to
indicate that the service must be carried
out as soon as possible.

Example: the service is overdue by
300 km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is switched
on, the distance recorder resumes its
normal operation. The spanner re-
mains lit .
The distance remaining may be
weighted by the time factor, de-
pending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval. Service indicator zero reset
After each service, the maintenance in-
dicator must be reset to zero.
The procedure for resetting to zero is as
follows:

 switch off the ignition,

 press and hold the trip distance re-
corder zero reset button,

 switch on the ignition; the distance
recorder display begins a count-
down,

 when the display indicates "=0" ,
release the button; the spanner dis-
appears. Retrieving the service information
You can access the service information
at any time.

 Press the trip distance recorder zero
reset button.
The service information is displayed for
a few seconds, then disappears. Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi ve minutes for the zero reset to
be taken into account.

1
INSTRUMENTS and CONTROLS
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life.
The total and trip distances are dis-
played for thirty seconds when the igni-
tion is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.

 With the ignition on, press the button
until zeros appear.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver. Clock
Adjusting the time - Choice of units

 press the button for more than
two seconds: °C or °F is displayed,

 press the button to select °C or °F,

 press the button for more than
two seconds to complete the adjust-
ments.
After approximately 30 seconds without
any action, the screen returns to the
normal display.
To adjust the time of the clock and
choose the units used by the screen,
use the right-hand button on the instru-
ment panel, carrying out the operations
in the following order:

 press the button for more than
two seconds: the minutes fl ash,

 press the button to increase the
minutes,

 press the button for more than
two seconds: the hours fl ash,

 press the button to increase the
hours,

 press the button for more than
two seconds: 24 H or 12 H is dis-
played,

 press the button to select 24 H or
12 H,