2008 YAMAHA YFM80R brake

9-1
1
2
3
4
5
6
7
89
10
11

EBU25860
CLEANING AND STORAGE
EBU25880
Cleaning
Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.
CAUTION:

ECB00710
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical de-
vices. Many expensive repair bills have result-
ed from improper high-pressure detergentapplications such as those available in coin-
operated car washers.
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.WARNING
EWB02310
Wet brakes may have reduced stopping ability,
increasing the chance of an accident. Test the
brakes after washing. Apply the brakes several
times at slow speeds to let friction dry out the

10-3
1
2
3
4
5
6
7
8
910
11
Front tire:

Type:
Tubeless
Size:
AT18 x 7-7
Manufacturer/model:
DUNLOP/KT586
Rear tire:
Type:
Tubeless
Size:
AT18 x 8-7
Manufacturer/model:
DUNLOP/KT587
Loading:
Maximum loading limit:
95.0 kg (209 lb)
(Total weight of rider, cargo, accessories, and tongue)
Tire air pressure (measured on cold tires):
Recommended:
Front:
20 kPa (2.9 psi) (0.20 kgf/cm
2

)
Rear:
20 kPa (2.9 psi) (0.20 kgf/cm
2

)
Minimum:
Front:
17 kPa (2.5 psi) (0.17 kgf/cm
2

)
Rear:
17 kPa (2.5 psi) (0.17 kgf/cm
2

)Maximum:
Front:
23 kPa (3.3 psi) (0.23 kgf/cm
2

)
Rear:
23 kPa (3.3 psi) (0.23 kgf/cm
2

)
Front wheel:
Wheel type:
Panel wheel
Rim size:
7 x 5.5AT
Rear wheel:
Wheel type:
Panel wheel
Rim size:
7 x 6.5AT
Front brake:
Type:
Drum brake
Operation:
Right hand operation
Rear brake:
Type:
Drum brake
Operation:
Left hand and right foot operation
Front suspension:
Type:
Leading arm
Spring/shock absorber type:
Coil spring/oil damper

INDEX
A
Accessories and loading ................................................ 6-7
Air filter element, cleaning ............................................ 8-13
Air intake restrictor plate, removing.............................. 8-17
B
Battery .................................................................. 5-6
,
8-29
Brake and shift pedals, checking and lubricating ......... 8-28
Brake lever and brake pedal free play (rear),
adjusting..................................................................... 8-23
Brake lever free play, adjusting the front...................... 8-21
Brake lever, front ............................................................ 4-4
Brake levers, checking and lubricating......................... 8-27
Brake pedal and rear brake lever ................................... 4-5
Brakes, front and rear .................................................... 5-3
Brake shoes, checking the front and rear .................... 8-20
C
Cables, checking and lubricating ................................. 8-26
Carburetor, adjusting.................................................... 8-18
Chassis fasteners........................................................... 5-6
Choke ........................................................................... 4-10
Cleaning ......................................................................... 9-1
Clutch free play, adjusting ............................................ 8-26
E
Engine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-18Engine oil ............................................................... 5-3
,
8-9
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-2
F
Final gear oil......................................................... 5-3
,
8-12
Front knuckle pivots, lubricating ................................... 8-28
Fuel ........................................................................ 4-7
,
5-3
Fuel cock ........................................................................ 4-8
Fuel tank cap.................................................................. 4-7
Fuse, replacing............................................................. 8-31
H
Handlebar switches ........................................................ 4-2
I
Identification numbers .................................................. 11-1
Indicator light .................................................................. 4-1
Instruments, lights and switches .................................... 5-6
K
Key identification number ............................................. 11-1
L
Label locations ............................................................... 2-1
M
Main switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-2

N
Neutral indicator light ..................................................... 4-1
O
Owner’s manual and tool kit ........................................... 8-1
P
Parking ........................................................................... 6-5
Parking brake ................................................................. 4-6
Parking on a slope ......................................................... 6-6
Part locations ................................................................. 3-1
Pre-operation check list.................................................. 5-1
R
Riding your ATV ............................................................. 7-1
S
Safety information .......................................................... 1-1
Seat .............................................................................. 4-10
Shifting ........................................................................... 6-3
Shift pedal ...................................................................... 4-6
Spark arrester, cleaning ............................................... 8-17
Spark plug, checking ...................................................... 8-8
Specifications ............................................................... 10-1
Speed limiter and air intake restrictor plate .................... 4-3
Start switch..................................................................... 4-2
Steering shaft, lubricating............................................. 8-28
Storage........................................................................... 9-2
T
Throttle cable free play, checking ................................ 8-19
Throttle lever .......................................................... 4-2
,
5-4
Timing chain ................................................................. 8-20
Tire pressure, measuring ............................................... 5-5
Tires ............................................................................... 5-4
Tire wear limit ................................................................. 5-6Troubleshooting ........................................................... 8-33
Troubleshooting chart .................................................. 8-35
V
Valve clearance............................................................ 8-20
Vehicle identification number ....................................... 11-1
W
Wheel hub bearings, checking ..................................... 8-28
Wheel, installing ........................................................... 8-33
Wheel, removing .......................................................... 8-32