2008 YAMAHA XT660Z wheel bolts

1
2
3
4
5
6
7
8
9
10
PRE-OPERATION CHECKS
4-3
ITEM
Clutch
Throttle grip
Control cables
Drive chain
Wheels and tires
Brake pedal
Brake and
clutch levers
Sidestand
Chassis fasteners CHECKS
• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing.
• Make sure that operation is smooth.
• Lubricate if necessary.
• Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.
• Make sure that operation is smooth.
• Lubricate pedal pivoting point if necessary.
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
• Make sure that operation is smooth.
• Lubricate pivot if necessary.
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary. PAGE
3-10, 6-20, 6-26
6-16, 6-266-25
6-23, 6-24, 6-25
6-16, 6-196-27
6-26
6-27–

XT660Z 04-06 ING 11-03-2008 8:30 Pagina 3

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (x 1,000 km)
110203040
ANNUALCHECK
√√√√ √
√√√√
√√√√ √
√√√√
√√√√
√√√√√ √√√√ √
√√√√ √
√√√√√ √8✻
9✻
10✻
11✻
12✻
13
14
✻
15✻
16
17
✻
• Check for cracks or damage.
• Replace.
• Check runout, spoke tightness and for damage.
• Tighten spokes if necessary.
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
• Check bearing for looseness
or damage.
• Check operation and for excessive play.
• Lubricate with lithium-soap-based grease.
• Check chain slack, alignment and condition.
• Adjust and lubricate chain with a special O-ring
chain lubricant thoroughly.
• Check bearing play and steering for roughness.
• Lubricate with lithium-soap-based grease.
• Make sure that all nuts, bolts and screws are
properly tightened.
• Check operation.
• Lubricate.
• Check operation.
Every 4 years
Brake hoses
Wheels
Tires
Wheel bearings
Swingarm
Drive chain
Steering bearings
Chassis fasteners
Sidestand
Sidestand switch
Every 50000 km
Every 500 km and after washing
the motorcycle or riding in the rain
Every 20000 km

XT660Z 04-06 ING 11-03-2008 8:30 Pagina 6-3

PERIODIC MAINTENANCE AND MINOR REPAIR
6-36
1
2
3
4
5
6
7
8
9
10
To service the rear wheel
Raise the rear wheel off the ground by
using a motorcycle stand or, if a mo-
torcycle stand is not available, by plac-
ing a jack either under each side of the
frame in front of the rear wheel or un-
der each side of the swingarm.EAU24360
Front wheelEAUB1440To remove the front wheel
EWA10820
WARNING0
●It is advisable to have a Yama-
ha dealer service the wheel.
●Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Wheel axle
2. Brake caliper bolts
A. Front wheel axle pinch bolt
B. Front wheel axle pinch bolt

A
2
B
1

EAU24350
Supporting the motorcycle
Since this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motorcy-
cle is in a stable and level position be-
fore starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel 1. Stabilize the rear of the motorcy- cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing a
jack under the frame in front of the
rear wheel.
2. Raise the front wheel off the ground by using a motorcycle
stand.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-36

1
2
3
4
5
6
7
8
9
10
PERIODIC MAINTENANCE AND MINOR REPAIR
6-37
1. Loosen the front wheel axle pinchbolts, the wheel axle and the
brake caliper bolts.
2. Lift the front wheel off the ground according to the procedure on
page 6-36.
3. Remove the brake caliper on each side by removing the bolts.
ECA11050CAUTION:
Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.
4. Pull the wheel axle out, and then remove the wheel.
EAUB1470
To install the front wheel1. Lift the wheel up between the fork legs.
2. Insert the wheel axle.
3. Install the brake calipers by in- stalling the bolts.
NOTE:
Make sure that there is enough space
between the brake pads before in-
stalling the brake calipers onto the
brake discs.
4. Lower the front wheel so that it is on the ground.
5. Tighten the wheel axle and the brake caliper bolts to the specified
torques.
ECAB0060CAUTION:
Be sure the right brake disc is posi-
tioned exactly in the middle of the
caliper pads to prevent any brake
drag. Tap the side of the right fork
leg to position the disc correctly.
Tightening torques: Wheel axle:60 Nm (6.0 m·kgf, 44 ft·lbf)
Front wheel axle pinch bolt: 18 Nm (1.8 m·kgf, 13 ft·lbf)
Brake caliper bolt: 40 Nm (4.0 m·kgf, 29 ft·lbf)
6. Tighten wheel axle pinch bolt A, and then pinch bolt B to the spec-
ified torque.
7. Retighten pinch bolt A to the specified torque.
8. Apply the front brake several times, and then while holding the
brake lever in, push down hard on
the handlebar several times to
check for proper fork operation.

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-37

PERIODIC MAINTENANCE AND MINOR REPAIR
6-38
1
2
3
4
5
6
7
8
9
10
NOTE:
●If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.
●The drive chain cannot be disas-
sembled.
7. While supporting the brake caliper bracket, pull the wheel
axle out, and then remove the
wheel.
ECA11070CAUTION:
Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.
EAU25080
Rear wheelEAU25311
To remove the rear wheelEWA10820
WARNING0
●It is advisable to have a Yama-
ha dealer service the wheel.
●Securely support the motorcy-
cle so that there is no danger of
it falling over.
1. Wheel axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chain

3
4
1

1. Wheel axle
2. Drive chain slack adjusting bolt
3. Locknut
4. Brake caliper

1. Loosen the axle nut.
2. Lift the rear wheel off the ground according to the procedure on
page 6-36.
3. Remove the axle nut.
4. Loosen the locknut on each side of the swingarm.
5. Turn the drive chain slack adjust- ing bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the rear sprocket.

4
3
1
2
a

XT660Z 04-06 ING 11-03-2008 8:31 Pagina 6-38